ADTRAN NetVanta Series User manual

Technical Support 1-888-4ADTRAN (1-888-423-8726)

NetVanta Series

(with Serial Network Interface Module)

Quick Configuration Guide 64200866L1-42A February 2004

• V.35 or X.21 cable for connecting the system to the existing network.

• VT100 terminal or PC with VT100 emulation software.

• DB-9 (male) to DB-9 (female) straight-through cable for configuring the unit.

Equipment Required

Cable length for the Serial interface should not exceed 25 feet.

This quick start guide provides step-by-step instructions for configuring your application. The

configuration scripts are available on the ADTRAN OS System Documentation CD.

Network Diagrams

Frame-Relay Diagram

PPP over Point-to-Point T1 Diagram

Branch Office Corporate HQ

NetVanta

LAN IP: 10.10.10.1/24

WAN IP: 192.168.72.2/30

eth 0/1

LAN IP: 10.10.20.7/24

PWR STAT TD

VPN

RD TD RD TD RD

WAN LAN

PWR STAT TD

VPN

RD TD RD

NetVanta3200

WAN LAN

DLCI 16

Annex D Signaling

192.168.72.1/30

FR 1

SHIFT

QUICK

TSUIQ

ENTER

CANCEL

NEXT PREV ADD

DELETE

TSU

SHIFT

QUICK

TSUIQ

ENTER

CANCEL

NEXT PREV ADD

DELETE

TSU

V.35 or X.21 V.35 or X.21

Branch Office Corporate HQ

NetVanta

LAN IP:

10.10.10.1/24

eth 0/1

LAN IP:

serial 1/1

10.10.20.7/24

WAN IP: 192.168.72.2/30

PWR STAT TD

VPN

RD TD RD TD RD

WAN LAN

PWR STAT TD

VPN

RD TD RD

NetVanta3200

WAN LAN

Point-to-Point T1

PPP Signaling

192.168.72.1/30

PPP 1

SHIFT

QUICK

TSUIQ

ENTER

CANCEL

NEXT PREV ADD

DELETE SHIFT

QUICK

TSUIQ

ENTER

CANCEL

NEXT PREV ADD

DELETE

TSU TSU

V.35 or X.21V.35 or X.21

2 Technical Support 1-888-4ADTRAN (1-888-423-8726) 64200866L1-42A

1Configuring the Unit

The NetVanta may be initially accessed and managed either via a console session or

through a Telnet session. See step 1a for console session instructions. Initiating a Tel-

net session requires using a hub and two Ethernet cables (one for the PC and one for

the unit). The default Ethernet IP address is 10.10.10.1. Refer to step 9 to change Tel-

net session settings.

1a Initiating a Console Session

1. Connect a VT100 terminal (or PC with VT100 emulation software) to the NetVanta

CONSOLE port using a DB-9 (male) to DB-9 (female) straight-through serial cable.

2. Configure the COM port with the following parameters:

Data Rate: 9600

Data Bits: 8

Parity Bits: None

Stop Bits: 1

Flow Control: None

3. Open a VT100 terminal session. (Please refer to the appropriate VT100 terminal

software documentation for detailed instructions.)

4. Press the <Enter> key.

5. Enter enable at the >prompt.

6. Enter the password when prompted. The default password is password. You are

now at the #prompt. At the # prompt, enter config terminal to enter the global

configuration mode.

The configuration parameters used in the example outlined in this document are for

instructional purposes only. Please replace all underlined entries (example) with your

specific parameters to configure your application

64200866L1-42A Technical Support 1-888-4ADTRAN (1-888-423-8726) 3

2Configuring the Ethernet Port Parameters

1. At the (config)# prompt, enter interface eth 0/1 to access the configuration

parameters for the Ethernet port located on the rear panel of the unit.

2. Enter ip address 10.10.20.7 255.255.255.0 to assign an IP address to the Ethernet

port using a 24-bit subnet mask.

If you are accessing the NetVanta via Telnet, once you change this IP address, you will

lose connection to the NetVanta. You must change the IP address of your PC before you

can proceed.

ADTRAN recommends that you set the Ethernet speed and duplex to match the switch or

hub it is plugged in to.

For example: (config-eth 0/1)#speed 10

(config-eth 0/1)#half-duplex

3. Enter no shutdown to activate the interface to pass data.

4. Enter exit to exit the Ethernet interface commands and return to the global

configuration mode.

The NetVanta Network Interface Modules (NIMs) use a slot/port notation for interface

identification. All non-modular interfaces built into the base unit (e.g., the Ethernet port) are

identified using 0 as the slot number.

3Configuring the Serial Interface

The following steps demonstrate configuring a serial network interface.

1. At the (config)# prompt, enter interface serial 1/1 to activate the interface

configuration mode for the serial network interface.

2. Enter serial-mode v35 to configure the serial interface for use with the V.35 adapter

cable (P/N 1200873L1).

3. Enter no shutdown to activate the interface to pass data.

4 Technical Support 1-888-4ADTRAN (1-888-423-8726) 64200866L1-42A

Skip to step 6 for PPP configuration.

4Configuring the Frame-Relay Virtual Interface

The following steps outline configuring a frame-relay virtual interface (labeled 1) using

a single DLCI back to the corporate router (defined as DLCI 16).

1. At the (config)# prompt, enter interface fr 1 to create a frame-relay virtual interface

labeled 1.

2. If the default setting of ansi was changed, enter frame-relay lmi-type ansi to

configure frame-relay virtual interface 1 to use ANSI (Annex D) signaling.

3. Enter no shutdown to activate the virtual interface to pass data.

4. Enter exit to return to the global configuration mode.

5. The unit has a factory default PPP 1 interface. Enter the command no ppp 1 to

remove this interface.

5Creating the PVC and Assigning an IP Address

1. At the (config)# prompt, enter interface fr 1.16 to create a PVC assigned to frame-

relay virtual interface 1. This activates the configuration parameters for the PVC.

Your prompt should now display (config-fr 1.16)#.

2. Enter frame-relay interface-dlci 16 to assign DLCI 16 to this PVC.

3. Enter ip address 192.168.72.1 255.255.255.252 to assign an IP address of

192.168.72.1 for this PVC using a 30-bit subnet mask.

4. Enter exit to return to the global configuration mode.

5. If you are configuring the NetVanta for use in a frame-relay application and have

completed this step, skip to step 7.

The default encapsulation is RFC 1490 or IETF. Make certain the remote unit uses the same

encapsulation for frame-relay.

6Configuring the Virtual PPP Interface

The following steps show how to configure a PPP virtual interface (labeled 1) to the

corporate router. Skip to step 7 if you are using frame-relay.

1. At the (config)# prompt, enter interface ppp 1 to create a PPP virtual interface

labeled 1.

2. Enter ip address 192.168.72.1 255.255.255.252 to assign an IP address to the

PPP endpoint using a 30-bit mask.

3. Enter no shutdown to activate the virtual interface to pass data.

4. Enter exit to return to the global configuration mode.

64200866L1-42A Technical Support 1-888-4ADTRAN (1-888-423-8726) 5

7Creating the Cross-Connect

1. For frame-relay applications, at the (config)# prompt, enter cross-connect 1 serial

1/1 frame-relay 1 to connect the serial NIM to the virtual frame-relay interface

(fr 1.16).

2. For PPP applications, enter cross-connect 1 serial 1/1 ppp 1 to connect the serial

NIM to the virtual PPP interface labeled 1.

8Configuring the Routes

Depending on your network setup, configure your unit in one of the following ways

beginning at the (config)# prompt:

Scenario 1: Static Route to the Far Side/Internet Access at Local Site

1. Set up the static route: ip route 10.10.10.0 255.255.255.0 ppp 1

(or frame-relay 1.16).

2. Set up the default route: ip route 0.0.0.0 0.0.0.0 10.10.20.x (i.e., address of

internet router).

Scenario 2: No Internet Access at Local Site

1. Set up the default route: ip route 0.0.0.0 0.0.0.0 ppp 1 (or frame-relay 1.16).

2. The internet router at the far side will need a route statement to send traffic back to

this network through the NetVanta 3205. The information (based on the diagram

shown at the beginning of this document) is as follows:

• Destination address: 10.10.20.0 (remote LAN)

• Subnet mask: 255.255.255.0

• Gateway: 10.10.10.1 (NetVanta 3205’s Ethernet)

6 Technical Support 1-888-4ADTRAN (1-888-423-8726) 64200866L1-42A

9Configuring Telnet

The following steps show how to access the Telnet configuration parameters and

change the password. The default password for initializing a Telnet session is

password (all lower-case). For security purposes, change the password to something

unique. For this example, replace the underlined word with a password of your

choosing. The NetVanta supports five Telnet sessions (0-4).

1. Verify that the prompt of your unit displays (config)#.

2. Enter line telnet 0 4 to change the configuration parameters for the Telnet session.

3. Enter password word to change the login password for the Telnet session.

4. Enter exit to return to the global configuration mode.

An enable security mode password must be defined before configured Telnet sessions are

activated. See the following step (Step 10) for information on password configuration.

10 Setting the Enable Security Mode Password

1. Verify that the prompt of your unit displays (config)#.

2. Enter enable password word to set the enable security mode password.

3. Enter enable password md5 word to encrypt the enable password using MD5

encryption.

The enable command security level passwords are case sensitive.

11 Saving the Configuration

1. Verify that the prompt of your unit displays (config)#.

2. Enter exit to leave configuration mode.

3. Enter copy running-config startup-config to save the current configuration to

memory. This command may be abbreviated as copy run start.

4. Enter exit to close the configuration session.

12 Completing the Installation

The NetVanta is now configured and operational. Complete the installation by connect-

ing the appropriate cables to the serial and Ethernet networks. Please refer to the

NetVanta Hardware Installation Guide for more details on pinouts and cabling.

Table of contents

Other ADTRAN Network Hardware manuals

ADTRAN

ADTRAN Stub Routing User manual

ADTRAN

ADTRAN Total Access 850 Instruction Manual

ADTRAN

ADTRAN ESU 120e User manual

ADTRAN

ADTRAN QFO-C Instruction Manual

ADTRAN

ADTRAN DSU 5600 User manual

ADTRAN

ADTRAN NetVanta Series User manual

ADTRAN

ADTRAN QDFR Unit Instruction Manual

ADTRAN

ADTRAN NetVantaE1/FE1 User manual

ADTRAN

ADTRAN Total Access 480 User manual

ADTRAN

ADTRAN BR10 User manual

ADTRAN

ADTRAN ATLAS 550 User manual

ADTRAN

ADTRAN CenturyLink C424G User manual

ADTRAN

ADTRAN 1442470F1 User manual

ADTRAN

ADTRAN Total Access 3000 Manual

ADTRAN

ADTRAN jobAid 1442351G1 User manual

ADTRAN

ADTRAN ISU 2X64 User manual

ADTRAN

ADTRAN NETVANTA 6355 User manual

ADTRAN

ADTRAN T200 IDSL OCU-R Instruction Manual

ADTRAN

ADTRAN AOC QSFP28 100G AOC QSFP28 100G 3M User manual

ADTRAN

ADTRAN SLC-5 U-BR1TE III Instruction Manual

ADTRAN

ADTRAN jobAid NETVANTA User manual

ADTRAN

ADTRAN 1442980G1C User manual

ADTRAN

ADTRAN U-BR1TE Maintenance and service guide

ADTRAN

ADTRAN NetVanta 6355 PoE User manual

Popular Network Hardware manuals by other brands

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL product manual

B&B Electronics

B&B Electronics ZXT9-IO-222R2 product manual

Yudor

Yudor YDS-16 user manual

D-Link

D-Link ShareCenter DNS-320L datasheet

Samsung

Samsung ES1642dc Hardware user manual

Honeywell Home

Honeywell Home LTEM-PV Installation and setup guide

evertz

evertz 7700 Series manual

D-Link

D-Link ShareCenter DNS-343 Quick installation guide

Asante

Asante AsanteBridge 1012 user guide

FireBrick

FireBrick FB2700 user manual

Audiovox Electronics

Audiovox Electronics ARWH2T user manual

ADC

ADC DSX-1 Operational Procedures Guide

NetComm

NetComm NF2 user guide

Alcatel-Lucent

Alcatel-Lucent 5620 user guide

Dell EMC

Dell EMC XC6420 Series Solution guide

Lanner

Lanner NCA-1020A user manual

Allied Telesis

Allied Telesis AT-TN121-A Specifications

Arista

Arista CCA-ETM-Q12 quick start guide