Adamson M15 User manual
M15 - MASS Rigging Manual p. 1
The M15 optional accessories include the MASS™ (Multi Angle
Suspension System) which features several different methods of
flying the cabinet.
The M15 is designed to receive a multi-purpose rigging plate, which
is the base for the following rigging methods covered in the manual.
MASS™ is designed for a single or a pair of M15’s.
MASS™ is perfect for installation applications and is available upon
request.
MASS™ can only be used with the M15 of the M Series monitors.
M15 - MASS Rigging Manual p. 2
When mounting the M15 with MASS™, ensure the boxes are securely fastened and mounted properly. Suspended
speakers should always be reinforced with steel safety cable and inspected by an experienced crew member.
When pole mounted, verify the stand is placed on a level surface, the tripod legs are fully extended and do not
present a trip hazard. in adverse outdoor conditions it may be necessary to support the base of the stand with
additional weight.
It is good practice to regularly inspect any cabinets housings for signs of wear, and load bearing bolts in mounting
devices. MASS™ is intended for use with the M15 only.
M15 - MASS Rigging Manual p. 3
For placing the Multi-Purpose plate in place for all MASS™ rigging
methods
1. Take the multi-purpose plate
2. Allign with the top of the box and
fit the locking hub into place
3. Pull the retaining pin up and slide
it in.
2.
3.
1.
M15 - MASS Rigging Manual p. 4
Option1:
Pole Mount - Rigging
Parts needed:
(1) Multi-Purpose plate
(1) Polemounting attachment
(Part not included. Can be ordered from
Koenig & Meyer part number - 195/8 Mounting Adapter)
M15 - MASS Rigging Manual p. 5
1. Screw the polemounting piece horinzontally to the multipurpose
plate. (1/4’ 20 machine screw, 1/2” long.
2. Fasten the plate to the M15 as on page 3.
3. In the event that you have the “flytrack” installed onto the
multipurpose plate and do not want to uninstall it, you can
screw the pole mounting piece verticallly. This will cover a part
of the protractor, and therefore we suggest using a horizontal
pole mount placement whenever possible.
Note- In this position the cabinet is not gravity centered, therefore
ensure the tripod legs are fully extended and reinforced as
required.
Option1:
Pole Mount - Rigging
M15 - MASS Rigging Manual p. 6
Parts needed:
(1) Multi-purpose plate
(1) C-clamp
Option2:
C-clamp - Rigging
M15 - MASS Rigging Manual p. 7
1. Screw the C-Clamp into the Multi-purpose rigging plate.
2. Fasten securely with a nut
3. Slide the Multi-Purpose plate to place as on page 3.
4. Be sure the bolt head’s height is not greater than the 1/4”
countersink allows, to avoid cosmetic damage to the box.
Option2:
C-clamp - Rigging
M15 - MASS Rigging Manual p. 8
Parts Needed:
(1) Multi-pupose plate
(2) Flytrack rigging pieces
(2) Suspension Hardware (not included)
Option 3:
Fly-Track Rigging
M15 - MASS Rigging Manual p. 9
1. Secure the MASS™ flytracks into position with provided machine
screws.(3/8 16th)
2. Attach the rigging plate as on page 3.
3. Attach suspension hardware if a more pronounced angle is
required. Flytrack option is adjustable to 5 different placements for varied
degreed angles: -9, -5.5, 0, +5.5, +9 degrees
Option 3:
Fly-Track Rigging
M15 - MASS Rigging Manual p. 10
A.
B.
D.
C.
B.
E.
F.
Option 4:
Single Axis Rigging
Parts needed:
(2) Multi Purpose
Plates x 2 (A.)
(2) Protractor
Discs (B.)
(1) U-bar (C.)
(1) C-Clamp (D)
Option 5:
Dual Axis Rigging
For Dual Axis Rigging (with a single box, you will also need:
(2) Protractor Discs (B.)
(1) Swing Assembly (E.)
(1) L-bar (F)
Table of contents
Other Adamson Speakers manuals
Adamson
Adamson IS Series User manual
Adamson
Adamson S-SERIES User manual
Adamson
Adamson S10n User manual
Adamson
Adamson S10p User manual
Adamson
Adamson IS7p User manual
Adamson
Adamson Point Series User manual
Adamson
Adamson IS7 User manual
Adamson
Adamson CS Series User manual
Adamson
Adamson S7 User manual
Adamson
Adamson CS Series User manual
