ACME Beluga User manual

CONTENTS

1. Safety Instructions ............................................................................................................................ 2

2. Technical Specifications .................................................................................................................... 5

3. Control Panel .................................................................................................................................... 6

4. How to set the Unit .......................................................................................................................... 7

4.1 Menu .............................................................................................................................................. 7

5. Control by DMX 512 controller ...................................................................................................... 15

5.1 DMX Connection .......................................................................................................................... 15

5.2 DMX Address Setting .................................................................................................................... 16

5.3 DMX Configuration ....................................................................................................................... 17

7. Troubleshooting ............................................................................................................................. 20

8. Fixture Cleaning ............................................................................................................................. 20

6. Error Message ................................................................................................................................ 18

1. Safety Instructions

WARNING

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that

they also receive this instruction manual.

Important:

Damages caused by the disregard of this user manual are not subject to warranty. The dealer will

not accept liability for any resulting defects or problems.

Unpack and check carefully that there is no transportation damage before using the unit.

This product is suitable for indoor use and wet locations. Do not immerse in water.

DO install and operate by qualified operator.

DO NOT allow children to operate the fixture.

Use safety chain when fixing the unit. Handle the unit by carrying its base instead of head only.

The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces.

Be sure that no ventilation slots are blocked, otherwise the unit will be overheated.

Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

Minimum ambient temperature TA: 0℃. Maximum ambient temperature TA: 40℃.

DO NOT connect the device to any dimmer pack.

Make sure there are no flammable materials close to the unit while operating to avoid fire

hazard.

Examine the power wires carefully; replace them immediately if there is any damage.

Unit’s surface temperature may reach up to 60℃. DO NOT touch the housing bare-handed

during its operation.

Avoid any inflammable liquids, water or metal objects entering the unit. Once it happens, cut

Please read the instruction carefully which includes important information about

the installation, usage and maintenance.

off the mains power immediately.

DO NOT operate in dirty or dusty environment, do clean fixtures regularly.

DO NOT touch any wire during operation as there might be a hazard of electric shock.

Avoid power wires together twist other cables.

The minimum distance between light output and the illuminated surface must be more than

0.5 meters.

Replace fuse/lamp only with the same type.

In the event of serious operating problem, stop using the unit immediately.

Never turn on and off the unit time after time.

The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.

DO NOT open the unit as there are no user serviceable parts inside.

Never try to repair the unit by yourself. Repairs carried out by unskilled people can lead to

damage or malfunction. Please contact the nearest authorized technical assistance center if

needed.

Disconnect the mains power if the fixture is has not been used for a long time.

DO use the original packing materials before transporting it again.

DO NOT look directly at the light while the bulb is on.

DO NOT start on the unit without bulb enclosure or when housing is damaged.

Installation:

The fixture should be mounted via its Omega Quick Release Clamp bracket. Always ensure that the

unit is firmly fixed to avoid vibration and slipping while operating and make sure that the structure

to which you are attaching the unit is secure and is able to support a weight of 10 times of the

fixtures weight. Always use a safety cable that can hold 12 times of the weight of the fixture when

installing.

The equipment must be installed by professionals. It must be installed in a place where is out of the

reach of people and no one can pass by or under it.

1. Bolt each clamp to the Omega holder with screw and lock nut through the hole in the holder.

2. Faster the omega holders on the bottom of the base by inserting quick-lock fasteners into the

holes of the base and tighten fully clockwise.

3. Hang the fixture to the support through clamp and faster the screws, Faster the safety cable

through the bottom of the base and over the support.

2. Technical Specifications

DMX Channels: 6/7 channels mode

LCD display for easy navigation

Perfect for stage, theatre, TV studio, rental and discotheques

Voltage:AC 100~240V, 50/60Hz

Power consumption: 310W

LED: 280W WW COB

Power Cord Daisy Chain: 10 Fixtures(240V/50Hz)

IP Grade IP66

Beam Angle: 7-23 Degree

Dimensions/Weight:

437.5x295x221mm, 10.5kgs

17.2"x9.7"x7.2"in,23.2bs

3.Control Panel

1. Monitor:

2. Button:

To enter into move backward or leave the menu

To go backward to move up in the menu

DOWN To go to move down in the menu

ENTER

To perform the desired functions

3 DMX output: DMX 512 operation, use 5 XLR cable to link the next units.

4. DMX input: DMX 512 link, use 5 XLR cable to link the unit and DMX controller.

5. Power In: To connect to the mains supply

6. Power Out: To connect to the next fixture

4. How to set the Unit

4.1 Menu

To select any of the given functions, press the MENU button up to when the required one is

showing on the display. Select the function by the ENTER button and the display will blink. Use the

DOWN and UP button to change the mode. Once the required mode has been selected, press the

ENTER button to setup, to go back to the functions without any change press the MENU button

again. Hold and press the MENU button about one second or wait for one minute to exit the menu

mode.

The main functions are showing below:

LED Use Hour

Total LED Hour

LED On Hour

LED Hours Reset

Passsword=050

Error Logs

Fixture Errors

Reset Error Log

Passsword=050

1-507(6ch)

1-506(7ch)

7CH

6CH

DMX Settings

Enter MENU mode, select DMX Functions, press the ENTER button to confirm, use the UP/DOWN

button to select DMX Address, DMX Channel Mode, View DMX Value or WDMX Setting.

DMX Address

To select DMX Address, press the ENTER button to show the DMX ADDRESS on the display.

Use the UP/DOWN button to adjust the address from 001 to 507, press the ENTER button to

setup. Press the MENU button back to the last menu or let the unit idle one minute to exit menu

mode.

DMX Channel Mode

To select DMX Channel Mode, press the ENTER button to show the DMX CHANNEL MODE on

the display. Use the UP/DOWN button to select Mode1 (6), Mode2 (7) , and press the ENTER

button to setup. Press the MENU button back to the last menu or let the unit idle one minute to

exit menu mode.

NO DMX Status

To select NO DMX Status, press the ENTER button to show two selections on the display.

Press the ENTER button to confirm, use the UP/DOWN button to select Black out or Hold

BlackOut: When the fixture out of DMX singnal ,it will stop working.

Hold: When the fixture out of DMX singnal ,it will stay in its final state and continues to run.

View DMX Value

To select View DMX Value, press the ENTER button to show the VIEW DMX VALUE on the

display. Use the UP/DOWN button to view the DMX channel values. Press the MENU button back

to the last menu or let the unit idle one minute to exit menu mode.

Fixture Setting

Enter MENU mode, select Fixture Setting, press the ENTER button to confirm, use the UP/DOWN

button to select Pan Inverse, Tile Inverse, BL.O. P/T Moving, Dimmer Curve or Dimmer Speed.

Dimmer Curve

To select Dimmer Curve, press the ENTER button to show the DIMMER CURVE on the display,

This manual suits for next models

Table of contents

Popular Lighting Equipment manuals by other brands

Brizo

Brizo 8SP-MU-4 manual

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 installation instructions

IKEA

IKEA BJÖRKSPIREA manual

Laserworld

Laserworld Evolution Series ES-400RGB manual

Alien

Alien RG STAR user manual

EuroLite

EuroLite LED B-40 user manual

Qazqa

Qazqa Suplux SL 3 Black 103062 instruction manual

Commercial Electric

Commercial Electric 54568141 Use and care guide

CREE LIGHTING

CREE LIGHTING 304 Series installation instructions

Goobay

Goobay 49867 user manual

ECOMAN ITALIA

ECOMAN ITALIA LED T8 instruction manual

Alkalite

Alkalite Krypton KT-81 user manual

Clas Ohlson

Clas Ohlson GU10 manual

DTS

DTS DELTA 10 F user manual

ring

ring Solar Steplight manual

One Stop Gardens

One Stop Gardens 57696 Owner's manual & safety instructions

Chauvet DJ

Chauvet DJ COREpar UV120 ILS user manual

SIREM

SIREM Swimeo A2 instructions