ACME LED-GBF User manual
User Manual
LED-GBF
1. Safety Instruction
Please keep this User Manual for future consultation. If you sell the unit
to another user, be sure that they also receive this instruction booklet.
Unpack and check carefully there is no transportation damage before
using the unit.
Before operating, ensure that the voltage and frequency of power supply
match the power requirements of the unit.
It’s important to ground the yellow/green conductor to earth in order to
avoid electric shock.
The unit must be installed in a location with adequate ventilation, at least
50cm from adjacent surfaces. Be sure that no ventilation slots are
blocked.
Disconnect mains power before replacement or servicing.
Replace only with the same type.
Make sure there are not flammable materials close to the unit while
operating, as it is fire hazard.
Use safety cable when fixes this unit.
In the event of serious operating problem, stop using the unit
immediately. Never try to repair the unit by yourself. Repair carried out by
unskilled people can lead to damage or malfunction. Please contact the
nearest authorized technical assistance center and always use the same
type spare parts.
Do not touch any wire during operation as high voltage might be causing
electric shock.
2. Installation
You can install the unit on the truss or ceiling. Use clamps to fix the unit to
truss. Always ensure that the unit is firmly fixed to avoid vibration and
slipping while operating. Always ensure that the structure to which you are
attaching the unit is secure. Also always use a safety cable that can hold 10
times of the weight of the unit when installing the fixture.
3. Technical Specification
Gobo Wheel: 15 gobos + white
Power supply: AC 100V/120V/230~250V, 50/60Hz
Power consumption：31W
LED:1 x 10 W Cool White
Dimension：246 x 192 x162 mm
Weight：2.8 kg
For power supply, do not connect in series much more than 19 units,
use another mains supply for next 19 units.
4. Function Instruction
○
1 Safety Ring: Keep the installation safe.
○
2 Gobo wheel switch: Use to set the state of gobo wheel. Set it to
mode, gobo wheel will rotate automatically; set it to mode, gobo wheel
will stop rotating; set it to mode, gobo wheel will rotate to music.
○
3 Reflector Dish: Use to set the state of reflector dish. Set it to mode,
reflector dish will rotate automatically; set it to mode, reflector dish will
stop rotating; set it to mode, reflector dish will rotate to music.
○
4 Mains output: Connect to supply mains power for the next unit.
○
5 Mains input: Connect to supply mains power.
○
6 Microphone: Receive music for the sound active.
This manual suits for next models
1
Table of contents
Other ACME Floodlight manuals
ACME
ACME BARRAGE LED-247 User manual
ACME
ACME Dynamic 25 Spin LED?GF25 User manual
ACME
ACME TV PANEL100 User manual
ACME
ACME CP?64 BD15 User manual
ACME
ACME IM-5S-ELC User manual
ACME
ACME LED-ST50 User manual
ACME
ACME LED-LP400 User manual
ACME
ACME Dragonfly User manual
ACME
ACME LED-4TC User manual
ACME
ACME CB-348TC User manual
ACME
ACME REFracted RLS 100 User manual
ACME
ACME TS-300M CW User manual
ACME
ACME BARRAGE LED-248 User manual
ACME
ACME SUPER NOVA RGB User manual
ACME
ACME LED-192RGB User manual
ACME
ACME LITE PANEL 900 LP-900 WW BD30 User manual
ACME
ACME MEGA STROBE 5000 User manual
ACME
ACME DMX 512 User manual
ACME
ACME LED-737 User manual
ACME
ACME BW-545 User manual
