aci TUCH User manual
Installation and Operation Instructions
ACI/TUCH Room Unit
GENERAL INFORMATION WIRING INSTRUCTIONS
The ACI/TUCH Room Unit is factory-configured to
support your specific requirements.
The number of wires needed to connect the ACI/TUCH
Room Unit to a controller depends on the application.
Most applications require five wires to support the
temperature output, the set point output, the RH output,
power, and ground (common); although some
applications will require additional wires. All signals
are common ground referenced. ACI recommends 16-
22 AWG twisted pair wires or shielded cable for all
sensor installations. Be sure to connect the cable
shield to the ground at the controller ONLY.
CAUTION
• CHECK THAT THE ACI/TUCH ROOM UNIT IS
CORRECTLY CONFIGURED FOR THE
APPLICATION; CONTACT ACI IF YOU ARE
UNSURE.
• THE ACI/TUCH ROOM UNIT IS A PRECISION
INSTRUMENT; PLEASE HANDLE IT WITH
CARE!
WIRING DIAGRAM
RH/FAN
RH signal to controller.
OFB
Occupied feedback signal from controller.
COM (-)
Ground or signal common, 20-28Vac (-).
POWER (+)
+15 to +30VDC, or 20-28Vac (+). See notes.
SEN
Temperature sensor signal to controller.
SET
Set point temperature signal to controller.
OR
Override signal to controller. See notes.
AUX
Auxiliary signal to/from controller. See notes.
MOUNTING INSTRUCTIONS
Separate the cover from the base. Attach the base
directly to drywall, or to a standard 2” x 4” junction box
using the mounting hardware provided. Refer to the
wiring instructions to make the necessary connections.
After wiring, attach the cover to the base and turn the
(2) hex-screws at the bottom of the base until the cover
cannot be removed.
WARNING
• REMOVE POWER BEFORE WIRING! NEVER
CONNECT OR DISCONNECT WIRING WITH
POWER APPLIED. DO NOT ALLOW LIVE
WIRES TO TOUCH THE CIRCUIT BOARD!
CAUTION
• WIRING MUST COMPLY WITH APPLICABLE
LOCAL AND NATIONAL ELECTRICAL
REGULATIONS.
NOTES:
1. The OR signal can be factory configured to short the SEN or SET terminals
to COM(-) to eliminate the need for a wire jumper between terminals OR and
SEN or SET outputs.
• DO NOT RUN THE ACI/TUCH ROOM UNIT
WIRING IN ANY CONDUIT WITH MAINS
POWER SYSTEM WIRING.
2. If the ACI/TUCH Room Unit has any output configured as 0-10V or 2-10V,
the voltage at the POWER(+) terminal must be at least +18VDC.
3. The AUX output/input is normally not used. For special applications, the
AUX output/input can be factory configured to support various functions.
• ACI RECOMMENDS USING A SEPARATE UL-
LISTED CLASS 2 TRANSFORMER WHEN
POWERING THE ACI/TUCH ROOM UNIT
WITH 24VAC! FAILURE TO WIRE DEVICES
WITH THE CORRECT POLARITY WHEN
USING A SHARED TRANSFORMER MAY
RESULT IN DAMAGE TO ANY DEVICE
POWERED BY THE SHARED TRANSFORMER.
2305 Pleasant View Rd. ●Middleton Industrial Park ●Middleton, WI 53562
PHONE (608) 831-2585 ●FAX (608) 831-7407
I0000493 REV 1 06/09/2008 Page 1 of 2
2305 Pleasant View Rd. ●Middleton Industrial Park ●Middleton, WI 53562
PHONE (608) 831-2585 ●FAX (608) 831-7407
I0000493 REV 1 06/09/2008 Page 2 of 2
Installation and Operation Instructions
ACI/TUCH Room Unit
KEY PAD
The ACI/TUCH Room Unit can be configured with
various keypad options containing from 1 to 4 keys that
operate the different functions, or an optional blank
insert may be provided if no control is desired.
O/R
MODE
O/R KEY (OPTIONAL):
Override key.
MODE KEY (OPTIONAL):
Mode adjust key used to change the
display mode from temperature to RH.
DOWN KEY (OPTIONAL):
Set point adjust key used to reduce
the set point value.
UP KEY (OPTIONAL):
Set point adjust key used to increase
the set point value.
OPERATIONAL MODES
The following diagrams show the operational modes of
the ACI/TUC Room Unit. The ACI/TUCH Room Unit
normally displays the room temperature, or the room
temperature alternating with the room RH.
°F
.5
Temperature display
Normally, the
ACI/TUCH Room
Unit shows the room
temperature. The
ACI/TUCH Room
Unit returns to this
screen 5 seconds
after the last
key-press activity.
%RH
RH display
%RH icon.
In alternate temperature
and RH display mode,
or when the optional
MODE key is pressed,
the ACI/TUCH Room
Unit shows the current
%RH value.
Setpoint
°F
Setpoint display
Setpoint icon.
When the UP or
DOWN keys are
pressed, the
ACI/TUCH Room
Unit shows the
current set point
temperature.
SET POINT OPERATION
When the UP or DOWN key is pressed, the word
“Setpoint” appears and the current set point temperature
is displayed. Additional UP or DOWN key presses
increment or decrement the set point temperature, while
continuously depressing the UP or DOWN key auto-
increments or auto-decrements the set point
temperature. The display continues to show the current
set point temperature for 5 seconds after the last UP or
DOWN key press and then returns to the temperature
display or the RH display.
RH MODE OPERATION
When the MODE key is pressed, the current %RH value
is displayed. The display continues to show the current
%RH value for 5 seconds after the last MODE key press
and then returns to the temperature display.
Other aci Air Conditioner manuals
Popular Air Conditioner manuals by other brands
Fujitsu
Fujitsu Inverter ASBA30JFC operating manual
Toshiba
Toshiba RAS-M10SMUV-E installation manual
Daikin
Daikin FXLQ20MAVE Operation manual
Hitachi
Hitachi RAS-E24CAK instruction manual
CIAT
CIAT Magister 2 Series Installation, Operation, Commissioning, Maintenance
Bestron
Bestron AAC6000 instruction manual
