Abus TVCC75100 User manual
TVCC75100
TVCC75200
User manual
Version 6/2011
Original English user manual. Keep for future use.
45
ĭ
Introduction
Dear Customer,
Thank you for purchasing this product.
This product meets the requirements of the applicable European and national guidelines.
The corresponding declarations and documents can be obtained from the manufacturer
(www.abus-sc.com).
To maintain this condition and to ensure risk-free operation, you as the user must observe these
operation instructions!
Before initial start-up, read through the complete operating instructions observing operating and
safety instructions.
All company and product names mentioned in this document are registered trademarks.
All rights reserved.
If you have any questions, please contact your installer or your local dealer!
Disclaimer
This user manual was prepared with greatest care. If you should notice omissions or inaccuracies,
please inform us about these on the back of this manual given address.
The ABUS Security-Center GmbH & Co. KG assumes no liability for technical and typographical
faults and reserves the right to make at any time modifications to the product or user manual
without a previous announcement.
The company is not liable or responsible for direct and indirect subsequent damages which are
caused in connection with the equipment, the performance and the use of this product.
No guarantee for the content of this document is taken.
46
Important safety instructions
The warranty will expire for damage due to non-compliance with these operating
instructions. We shall not be liable for any consequential loss!
We do not accept liability for damage to property or personal injury caused by incorrect
handling or non-compliance with the safety-instructions. In such cases the warranty will
expire.
Dear customer,
The following safety instructions are intended not only for the protection of your health, but also for
the protection of the device. Please read through the following points carefully:
xThere are no parts on the inside of the product which need to be serviced. Apart from this, the license
(CE) and the guarantee/warranty will lapse if you open/take the product apart.
xThe product will be damaged even it falls from a low height.
xThis device can be used in inside as well as outside.
xDuring the installation of the camera please take care that direct sunlight cannot fall onto the image
sensor of the device. Please follow the installation instructions in the corresponding chapter of this
user manual.
Avoid using the device under the following unfavorable ambient conditions:
xwetness or excessive air humidity
xextreme cold or heat
xdirect sunlight
xdust or combustible gases, vapors or solvents
xstrong vibration
xstrong magnetic fields, such as those found in the vicinity of machinery or loudspeakers
xThe camera should not positioned with opened iris towards the sun – this can lead to the
destruction of the sensor.
xthe camera may not be installed on unstable surfaces
General safety instructions:
xDo not leave packaging material lying around carelessly. Plastic/ foil/bags and polystyrene parts etc.
could become dangerous toys for children.
xFor safety reasons don’t give the camera into child hands due to them being able to swallow small
parts.
xPlease do not insert objects through the openings into the device.
xUse only accessories which are specified by the manufacturer.
Please do not connect incompatible parts to the device.
xPlease pay attention to the safety instructions and user manuals of the other connected devices.
xCheck the device for damages before installation. If this should be the case please do not use it.
xPlease adhere to the operational voltage limitations listed in the technical data. High voltage could
destroy the device and pose a health hazard (electric shock).
During the installation into an existing video surveillance system make sure that all
devices are disconnected from the low and supply voltage circuit.
If in doubt allow a professional electrician to mount, install and wire-up your device.
Improper or make-do electrical connection to the mains does only represent at threat to
you but also to other persons.
Wire-up the entire system making sure that the mains and low voltage circuit remain
separated and cannot come into contact with each other in normal use or due to any
malfunctioning.
47
Table of contents
1. SCOPE OF DELIVERY.............................................................................................................................48
2. FEATURES...............................................................................................................................................48
3. COMPONENTS NAMING.........................................................................................................................49
4. INSTALLATIONS INSTRUCTIONS..........................................................................................................50
4.1 CONNECTION METHOD ................................................................................................................................50
4.2 CEILING MOUNT TYPE..................................................................................................................................52
4.3 EMBEDDED MOUNT TYPE.............................................................................................................................54
4.4 INDOOR ADAPTOR.......................................................................................................................................55
4.5 DROPPED CEILING MOUNT BRACKET OR GOOSE NECK MOUNT BRACKET .........................................................56
4.5 ADDITIONAL ACCESSORIES..........................................................................................................................58
5. QUICK GUIDE CONTROL DEVICES.......................................................................................................60
5.1 CONTROL USING OPERATOR PANEL TV7605...................................................................................................60
5.2 CONTROL USING TV3000-TV3031 RECORDERS..............................................................................................60
6. QUICK OPERATING KEYS......................................................................................................................61
7. DIAGNOSTIC............................................................................................................................................63
8. OSD MENU SETTING ..............................................................................................................................64
8.1 OSD MENU TABLE........................................................................................................................................64
8.2 DOME SETUP..............................................................................................................................................65
8.3 CAMERA SET ..............................................................................................................................................70
8.4 PRESET SETTINGS ......................................................................................................................................72
8.5 AUTO SCAN SET..........................................................................................................................................73
8.6 TOUR SET...................................................................................................................................................74
8.7 PRIVACY SET..............................................................................................................................................75
8.8 PATTERN SET .............................................................................................................................................76
8.9 ALARM SET.................................................................................................................................................77
8.10 SECTOR ...................................................................................................................................................78
8.11 EXIT.........................................................................................................................................................78
9. DIP SWITCH SETTING.............................................................................................................................79
9.1 ID SETTING.................................................................................................................................................79
9.2 RS-485 TERMINATION...................................................................................................................................81
9.3 PROTOCOL.................................................................................................................................................81
9.4 BAUD RATE SETTING ...................................................................................................................................81
10. SPECIFICATIONS ....................................................................................................................................82
11. DIMENSIONS............................................................................................................................................82
48
1. Scope of Delivery
No. Item Qty.
1 Pan / Tilt dome camera 1
2 Ceiling Mount Bracket 1
3 24 V AC Power Supply 1
4 Wrench 1
5 Screws (Ø 3x6 screw) 2
6 Screws (Ø 4x16 screw) 5
7 Safety Wire 1
8 Manual 1
9 Ceiling cover 1
10 Cable ties 5
11 Terminal Block 2 PIN 2
12 Terminal Block 3 PIN 1
13 Terminal Block 5 PIN 1
14 Terminal Block 6 PIN 1
2. Features
The Pan/Tilt dome camera has among other the following functions:
xSpeedy response with 27 respectively 36 times continuous auto-focus zoom lens and
12 times Digital Zoom
xUp to 560 TVL resolution
xPassword protection
xLow-Noise-Technology for extremely quiet movement with 0,024° accuracy
xSlip ring for long life time (20 million rotate ring tested)
xAdvanced DSP camera, including Auto White Balance, Backlight Compensation and
Auto Iris Control
x165 Preset Points Setup
x8 programmable group tours, each one with up to 60 preset steps
xContinuous Auto Focus
x350°/sec pan and 250°/sec tilt speed on preset
xBuilt in 4 Alarm Inputs and 2 Relay outputs (NO/NC)
xRemote control via RS-485 (up to 127 Speed Dome Cameras controllable)
xPower misconnection protection on terminal
xChangeable IR-filter for true day/night
xSupports PECLCO (D and P) and Maxpro protocol
49
3. Components Naming
1. Bubble 8. Video Output
2. Lock Screw 9. Loop RX
3. DIP Switch 1 10. Loop TX
4. DIP Switch 2 11. Power LED
5. Camera 12. Aux terminal
6. Lock Holder 13. Alarm terminal
7. Power input 14. Mount Holder
FIG.1
50
4. Installations Instructions
4.1 Connection Method
1. To separate camera body loosen Lock Screw (2 mm), turning the wrench counterclockwise.
(Don’t pull the screw out) (FIG. 2)
Separate the upper body from the lower body by turning counterclockwise. (FIG. 3, 4)
2. After separating set DIP switches (Refer to the page 78)
3. To assemble camera body rotate the upper body clockwise to assemble both bodies.
(FIG. 5, 6). Screw up turning the wrench clockwise. (FIG. 7)
Don’t screw to tight, it can cause defects.
FIG.
2
FIG.4FIG.3
UNLOCK
2 mm
FIG.6FIG.5 FIG.7
LOCK
Screw up to flat with
the body surface
51
1. Alarm:4 Alarm inputs
2. AUX: DC 12 V with up to 1 A can be used at the AUX terminal.
Possible applications using AUX are e.g. turning on a light or remote control.
3. TX: TX transmits data signal received from RX to other equipment.
TX is convenient terminal for daisy chain connection.
4. RX: RX receives control signal from controller or DVR.
5. Video out: BNC connector (1Vp-p)
6. Power: AC 24 V 1.0 A adaptor
* Do not connect power supply to the middle screw of the power terminal.
Middle screw is for grounding only.
7. Power ON LED
52
4.2 Ceiling mount type
The Ceiling mount type is for suspended ceilings with at least 4 cm distance between structural slab
and ceiling. The complete camera body will be visible.
1. Select a ceiling board which is strong enough to hold a weight of approximately 2 kg.
2. Prepare a Ø 145 mm hole in the ceiling board. (FIG. 9)
Fix the safety wire to a suspension to prevent camera from falling.
Fix the other side of safety wire to the safety wire hole. (FIG. 10)
3. Fix the Ceiling Mount to the Ceiling with 4 screws (Ø 4.0 mm tapping screw). (FIG. 11)
4. Tie the wire using the cable ties. (FIG. 12)
5. Mount the wires through the square hole.
Place the Camera Mount Holder in the Bracket Mount Hole. (FIG. 12)
To insert them easily, keep 10° interval of Lock Holder1 and Lock Holder2. (FIG. 13)
53
6. To assemble, rotate the Camera clockwise 10°. (FIG. 13)
7. Screw up Lock Holders with screws (M3).
8. Assemble the Cover.
Fix three Cover Locks to three Cover Holes rotating clockwise. (FIG. 15)
10°
FIG.13 FIG.14
SCREW (M 3.0)
LOCK HOLDER .1
LOCK HOLDER .2
This manual suits for next models
1
Table of contents
Other Abus Security Camera manuals
Abus
Abus TVIP81000 User manual
Abus
Abus PPIC32020 User manual
Abus
Abus IPCB42501 User manual
Abus
Abus HDCC32500 User manual
Abus
Abus IPCB62500 User manual
Abus
Abus TVCC74000 User manual
Abus
Abus TVIP62500 User manual
Abus
Abus IPCB34511A User manual
Abus
Abus Eycasa CASA31000 Instruction manual
Abus
Abus IPCB62520 User manual
Abus
Abus Ecoline TV7100 User manual
Abus
Abus HDCC63550 User manual
Abus
Abus IPCS64531 User manual
Abus
Abus TVAC19000C User manual
Abus
Abus IPCB71500 User manual
Abus
Abus IPCS28581A User manual
Abus
Abus HDCC33500 User manual
Abus
Abus Eyseo TV7220 User manual
Abus
Abus TV7602 User manual
Abus
Abus IPCS82500 User manual
