ABB Relion 611 Series User manual

















—

Quick Start Guide

Relion® 611 series

Display Use navigation buttons for entering to submenus

Self-supervision and

protection indicator LEDs

Ready-LED steady: OK, Ready-LED flashing: Internal Relay Fault (IRF),

Start-LED steady: protection started, Start-LED flashing: protection function blocked,

Trip-LED: protection operated

Programmable LEDs Can be programmed for alarming and indication with latching and/or flashing features

Control Circuit Breaker (CB) Press open/close and confirm by pressing enter. Note: control has to be in Local mode.

Escape / Cancel Used for canceling actions and leaving setting mode without saving the values.

Returns back to menu.

Navigation Left = go back, Right = go further, Up = scroll up, Down = scroll down.

Are also used for changing setting values.

Enter / Select Entering to parameter setting mode and confirming new values

Local / Remote Changes the control between Local/Remote

Help View help menu

 Front communication port RJ-45 port can be used for connecting the IED to a PC

QUICK START GUIDE RELION® 611 SERIES

—

Using the local HMI

Accessing main menu and changing parameters

Press to navigate to the main menu from the measurements

view.

From the main menu, go to Settings and press .

Then press or to select the setting value you want

to change. Press to change it with or buttons.

If there is a “#” mark on the same line as the parameter value,

you have to first select which setting group parameter you

want to change. If there is no “#” mark then you can change

the value directly by pressing and then with or or

or buttons.

You can change all parameters in the same way. The most

common function block names are described at the end of

this document.

Storing settings

Parameters have to be stored before taken into use.

Store the settings by going back to the main menu by pressing

the button. The IED will ask for confirmation to commit

changes, answer “Yes“. Some changes require the IED to reboot

before the changes are taken into use. Reboot the IED by going

to main menu 

or by switching the auxiliary power off and back on.

Changing the overcurrent start value

From the main menu, go to 

setting group, default 1 and press 

.

Changing function block naming from IEC 61850 names

to IEC 60617

From the main menu, go to 

FB Naming convention.

Checking binary input value

From the main menu, go to 

.

Checking fault records and measurement values of

the latest faults

From the main menu, go to 

Fault record.

Clearing events, indications and programmable LEDs

From the main menu, go to Clear. Select the item you want to

clear and press and select Clear by pressing (Cancel

will disappear). Confirm by pressing .

Checking IED order code, serial number, HW revision and



From the main menu, go to .

Display header area

The icon area at the upper right corner of the dislay shows

the current action or user level. These are described below:

S= Parameters are being stored

!= Warning and/or indication

V= Viewer

O= Operator

E= Engineer

A= Administrator

Checking the input and output status of a function block

From the main menu, go to .

Checking the IP address

The address of the front communication port is fixed:

192.168.0.254. If the IED is equipped with a communication

card you can check the IP address of the rear communication

port from the main menu 

.

Activating the Web HMI

To activate the Web HMI from the main menu go to

. Activation requires

rebooting the IED.

Changing the display contrast

Hold and press or to change the display contrast.

The display contrast setting is automatically stored when A

(Administrator) is visible in the icon area at the upper right

corner of the display.

QUICK START GUIDE RELION® 611 SERIES

—

Using the Web HMI



a Ethernet cable. Enter the IP address 192.168.0.254 in







Changing the overcurrent start value via WebHMI

It is important to enable writing to the IED. If write is

disabled it is not possible to change settings.

Click settings in the left menu bar, then go to 

.

After you have changed the start value parameter, click

 and click  in the notification bar

that opens.

Input and output signal configuration

Click the corresponding area to view a specific logical

group, and then the switch groups included in the logical

group are listed in the Function View page. Click

 to go back to the overview page.

—

Changing the overcurrent start value via WebHMI

—

Input and output signal configuration

IMRS757627 REV C EN 02-2019

—

We reserve the right to make technical changes or modify the contents

of this document without prior notice. With regard to purchase orders,

the agreed particulars shall prevail. ABB does not accept any responsibility

whatsoever for potential errors or possible lack of information in this

document.

We reserve all rights in this document and in the subject matter and

illustrations contained therein. Any reproduction, disclosure to third

parties or utilization of its

contents – in whole or in parts – is forbidden

without prior written consent of ABB.

—

Most common function blocks

Function  

Three-phase non-directional overcurrent protection, low stage PHLPTOC 3I>

Three-phase non-directional overcurrent protection, high stage PHHPTOC 3I>>

Three-phase non-directional overcurrent protection, instantaneous stage PHIPTOC 3I>>>

Non-directional earth-fault protection, low stage EFLPTOC Io>

Non-directional earth-fault protection, high stage EFHPTOC Io>>

Non-directional earth-fault protection, instantaneous stage EFIPTOC Io>>>

Directional earth-fault protection, low stage DEFLPDEF Io> →

Directional earth-fault protection, high stage DEFHPDEF Io>> →

Transient / intermittent earth-fault protection INTRPTEF Io> → IEF

Negative-sequence overcurrent protection NSPTOC I2>

Phase discontinuity protection PDNSPTOC I2/I1>

Residual overvoltage protection ROVPTOV Uo>

Three-phase thermal protection for feeders T1PTTR 3Ith>F

Loss of load supervision LOFLPTUC 3I<

Motor load jam protection JAMPTOC Ist>

Motor start-up supervision STTPMSU Is2t n<

Phase reversal protection PREVPTOC I2>>

Thermal overload protection for motors MPTTR 3Ith>M

Circuit breaker failure protection CCBRBRF 3I>/Io>B F

Three-phase inrush detector INRPHAR 3I2f>

High-impedance differential protection HIPDIF dHi>

Phase segregated CT supervision function HZCCRDIF MCS 1I

Circuit-breaker control CBXCBR I ↔ O CB

Emergergency startup ESMGAPC ESTART

Trip circuit supervision TCSSCBR TCS

Runtime counter for machines and devices MDSOPT OPTS

Disturbance recorder RDRE DR

Optional

Auto-reclosing DARREC O → I

The most common function blocks are listed below, see the full list from the operators manual.

Available function blocks varies depending on the selected IED and standard configuration.

Complete customer documentation is available in the product pages that

can be accessed through abb.com/relion.

—

For more information, please contact

ABB Distribution Solutions

P.O. Box 699

FI-65101 Vaasa, Finland

Phone: + 358 10 22 11

abb.com/substationautomation

Other manuals for Relion 611 Series

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual