ABB FDNA-01 Installation manual

Other manuals for FDNA-01

2

Table of contents

Other ABB Control Unit manuals

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual

Options for ABB drives, converters and inverters

Quick installation and start-up guide

FDNA-01 DeviceNet adapter module

Safety instructions

WARNING! Obey the safety instructions. If you ignore them, injury or death, or damage to the

equipment can occur. See the user’s manual.

Mechanical installation

Electrical installation

Layout of the module

1. Pull out the lock.

2. Install the module carefully to an option

module slot of the drive. See the drive

hardware manual.

3. Push in the lock.

4. Tighten the screw to torque 0.8 N·m using

a Torx TX10 screwdriver.

WARNING! Do not use excessive force,

or leave the screw too loose. Over-

tightening can damage the screw or

module. A loose screw decreases the EMC

performance, and can even cause an operation

failure.

13

4



No. Description

1Lock

2 Mounting and grounding screw

3 Bus connector [X1]

4 Diagnostic LEDs

4

3

2

1

Start-up

When the module is connected to the drive, the drive control program sets the applicable parameters.

See the appropriate drive manual.

Basic parameter settings

To take the settings into use, validate and refresh the parameters with parameter 51.27 FBA par refresh.

Further information

Index Name Value

20.01 Ext1 commands Fieldbus A

22.11 Speed ref1 source FBA A ref 1

28.11 Frequency ref1 source FBA A ref 1

50.01 FBA A enable Enable (or select the option slot in which the module is installed).

This activates the communication module. The HOST LED becomes green.

50.02 FBA A comm loss func Fault

51.02 MAC ID Set the MAC ID number for the drive.

See the latest version of FDNA-01 DeviceNet adapter

module user's manual (3AFE68573360 [English]) in ABB

library (www.abb.com/drives/documents).

For more information on fieldbus options and protocols

provided by ABB Drives, see the fieldbus

communications web page

(new.abb.com/drives/connectivity/fieldbus-connectivity).

Pin allocation for [X1] Bus termination

The module does not provide bus termination. The DeviceNet

network should be terminated at both ends of the trunk cable with

a 121 ohm, ¼ W, 1% metal film resistor.

Connect the resistor between the two signal wires (CAN_H,

CAN_L) on the DeviceNet cable, as shown in this figure.

Pin Description

1 V- Network power supply

ground (0V DC)

2 CAN_L CAN_L bus line

3 SHLD Network cable shield

4 CAN_H CAN_H bus line

5 V+ Network power supply

source (24V DC)

12345

Node 1 Node n

121



CAN_H

CAN_L

Scanner

121



1%

Metal Film

1/4 W

1%

Metal Film

1/4 W

…

3AXD50000158515 Rev A (EN) 2017-11-23

FDNA-01 manual

Fieldbus communications web page