A4Tech RFKBS-15A User manual
1
Radio Wireless Keyboard
User
’
s Guide
Model: RFKBS-15A , RFKB-15A
2
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE FOLLOWING
TWO CONDITIONS:
(1) THIS DEVICE MAY
NOT CAUSE HARMFUL INTERFERENCE AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFER
ENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED
OPERATION.
Federal Communications Commission Requirements
The equipment has been tested and found to comply with the limits for Class B
Digital Device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction, may cause
harmful interference to radio communication. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
3
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
l Reorient of relocate the receiving antenna.
l Increase the separation between the equipment and receiver.
l Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
l Consult the dealer or an experienced radio/TV technician for help.
The changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
4
Getting Ready
1. Turn off the power of your computer.
2. Remove the existing keyboard (and mouse for the A4Tech®Wireless Desktop).
3. Install the AA alkaline batteries in the Wireless keyboard. Remove the battery compartment
cover on the bottom of the keyboard by squeezing the cover in from the tab to release it.
4. Install the AAA alkaline batteries in the Wireless mouse (for the A4Tech Wireless Desktop).
(a) Remove the battery compartment cover on the bottom of the mouse by pressing down on
the tab. Insert the batteries as shown in side the battery compartment. Replace the cover.
(b) Or press the up cover and move backward as shown here, and by sliding the cover off.
Insert the batteries as shown inside the battery compartment. Replace the cover.
5
Setting Up the Keyboard or Wireless Desktop
1. Make sure that your computer is turned off.
2. Connecting the Receiver’s Keyboard Cable:
(a) When connecting to an IBM AT keyboard port, use the 5-pin DIN
connector already attached to the keyboard cable.
(b) When connecting to a PS/2-style, 6-pin DIN keyboard port, remove the
AT adapter.
(c) Connect the receiver’s purple keyboard cable to the computer’s keyboard port.
3. Connecting the Receiver’s Mouse Cable (Wireless Desktop): Connect the receiver’s
green
mouse cable to the
computer’s PS/2 mouse
port
4. Place the receiver eight
inches (20 centimeters)
from any electromechanical
device.
6
Installing the Mouse Software-iWheelWorks and Keyboard
software-iKeyWorksOffice
Before you can take advantage of the many features your mouse and keyboard offers, you must install
the driver. The driver is in the installation diskette that came packaged with your mouse and keyboard
Windows 95/98/Me/2000/NT4.0 installation
Insert the installation diskette into your floppy disk drive.
Click the Start button and then click Run.
In the Run dialog window, type A:\setup, where “A” is the letter of your floppy disk drive.
Click OK and follow the instructions on your screen to complete the installation.
Selecting the Frequency Channel
The Wireless keyboard and Mouse operates on two frequency channels. To
prevent interference when using two RF Mice in close proximity a different
frequency channel should be used for each mouse. Refer to the following to change the frequency
channel for your keyboard and mouse: Set the frequency channel on
the receiver to 1 or 2. Set the frequency channel on the keyboard and
mouse to 1 or 2.
7
The Wireless keyboard and mouse ID code
Each keyboard and mouse is assigned a unique ID code at manufacture, so the receiver only picks up the
signal from your mouse and prevents other Wireless keyboard or mouse radio signals from operating on
your computer. This feature can also be disabled, allowing other Wireless pointing devices to operate
your computer.
Connecting the Wireless Mouse ID Code
When the driver installation is finished your computer reboots and the Wireless Mouse window (shown on the right)
appears.
CONNECT ID: Move the Wireless Mouse for a few seconds to establish a connection, then click
Conne
unique ID code of your mouse is recognized and another RF pointing device will not function on your computer.
Exit: Click Exit
if no other RF pointing devices are within 3 meters range or if you want other RF pointing devices to be
able to access your computer.
8
Changing the Wireless Mouse ID Code
You can use a new Wireless Mouse on your computer without changing the Radio receiver; you just
need to change the ID code. Refer to the following:
1. Press [Shift + Alt + F11] or [Shift + Alt + F12] to call up the Wireless Mouse ID Code window.
2. Move the Wireless Mouse for a few seconds to establish a connection, then click Connect ID.
3. The new ID code is connected and the Wireless Mouse window closes.
4. Click Exit to close the Wireless Mouse ID code window.
Connecting the Wireless Keyboard ID Code
Manually establish communication between the receiver and keyboard.
(a) Press any key from the keyboard
(b) Press the ID Connect button on the receiver the green LED light will show you the keyboard ID be
connect. If the green LED light is off then keyboard ID is disconnect.
This manual suits for next models
1
Table of contents
Other A4Tech Keyboard manuals
A4Tech
A4Tech RFKBS-61A User manual
A4Tech
A4Tech GD-300 User manual
A4Tech
A4Tech GK-300 User manual
A4Tech
A4Tech GX-100 User manual
A4Tech
A4Tech GK-23 User manual
A4Tech
A4Tech RFKBTX-5-1 User manual
A4Tech
A4Tech GR-152 User manual
A4Tech
A4Tech GV-300 User manual
A4Tech
A4Tech KBS-26 User manual
A4Tech
A4Tech GD-800 User manual
A4Tech
A4Tech GK-8 User manual
A4Tech
A4Tech GL-6 User manual
A4Tech
A4Tech GK-300A User manual
A4Tech
A4Tech GD-900 User manual
A4Tech
A4Tech RFKBS-27A User manual
A4Tech
A4Tech GL-100 User manual
A4Tech
A4Tech GR-76 User manual
A4Tech
A4Tech GK-21 User manual
A4Tech
A4Tech RFKBS-26A User manual
A4Tech
A4Tech GR-75 User manual
