3idee hp2xf-o User manual
www.3idee.eu
hp2xf-o VESA Adapter
Assembly instructions
The VESA adapter is compatible with the following products from hp
(hp.com): OMEN X 25f Gaming Monitor.
The VESA adapter allows you to conveniently mount your HP brand monitor to a
monitor arm with a VESA hole pattern (75 x 75mm). Use the included screws and
nuts.
If you want to mount your VESA adapter directly to the wall, use suitable screws
and dowels (not included).
2
Assembly instructions
Assembly instruction
Step 1
Place your screen in a safe, soft place so that your screen
does not get damaged.
Remove the base of your monitor if it is already attached.
Use a screwdriver and unscrew the two screws underneath
the mount. (Figure 1)
Don't put the two screws too far away, we will need them
again in a moment to fix the VESA adapter. Figure 1
Step 2
Now pull out the base of your monitor upwards. (Figure 2)
Figure 2
Step 3
Now insert the 3idee VESA adapter into your HP Omen
monitor. (Figure 3)
Figure 3
Step 4
Now you can reuse the two screws you loosened earlier to
attach the VESA adapter to your monitor. (Figure 4)
Figure 4
3Assembly instructions
Step 5
Please check if you have fastened the two screws correctly.
(Figure 5)
Figure 5
Step 6
Now hold the VESA adapter on your monitor arm and screw
it tight from behind with the other hand. (Figure 6)
Figure 6
Step 7
Figure
4
Assembly instructions
Safety instructions
General notes
Make sure that all screws are tight and that the monitor audibly clicks into place during installation (if
available).
The material of the adapter is not heat resistant. Avoid direct heat around the adapter such as PC
exhaust or direct sunlight in summer.
PLA is UV resistant but not suitable for high temperatures.
Avoid jerky movements (pulling, tearing) on the PC monitor. This can affect the performance of the
VESA adapter.
Do not subject the PC monitor to excessive loads such as leaning or pushing. This can impair the
performance of the VESA adapter.
Material Notes
The adapter is made of high-quality polylactide (PLA) plastic. PLA is both a colorfast and UV-resistant
material and has low flammability. Polylactide has a low temperature resistance of approx. 45°C-55°C
and is therefore not suitable for use in the vicinity of direct heat and heat sources.
We wish you a lot of fun with your product.
Your 3idee Team
Responsible for this content:
3idee Technologies S.à r.l
5, ZA Um Lenster Bierg
L-6125 Junglinster
Luxembourg
Powered by TCPDF (www.tcpdf.org)
Table of contents
Other 3idee Adapter manuals
3idee
3idee hp-f User manual
3idee
3idee ao-u28v User manual
3idee
3idee smsng-s32bm User manual
3idee
3idee hp-23p User manual
3idee
3idee smsng-s34b User manual
3idee
3idee acr-s24h User manual
3idee
3idee acr-hy User manual
3idee
3idee hp-eo-g9 User manual
3idee
3idee hp-27c-o User manual
3idee
3idee hp-z User manual
3idee
3idee hp-34f User manual
3idee
3idee hp-pav User manual
3idee
3idee hp-q User manual
3idee
3idee de-se2417 User manual
3idee
3idee ass-vz VESA User manual
3idee
3idee de-sdc User manual
3idee
3idee hp-32f User manual
3idee
3idee MSI - G241VC-017 User manual
3idee
3idee smsng-cwr32 User manual
3idee
3idee vs-vx24 User manual
