ZMODO Greet Universal User manual
Greet Universal
Quick Start Guide
1
The Greet Universal Smart Doorbell allows you to answer
your door from any location. The Greet Universal is powered
by an indoor chime, which is installed in the inside of your
home. This quick start guide will help you configure your
Greet Universal for initial use. For detailed instructions and
troubleshooting, please visit:
www.zmodo.com/support
Welcome!
Getting to know your Greet Universal
①
②
③
④
⑤
①
②
③
④
⑤
Plastic Cover
LED Light Indicator
Speaker
Power Port
Mounting Bracket
①
②
③
④
⑤
⑥
⑦
⑧
⑨
①
②
③
④
⑤
Camera
Microphone
PIR Motion Sensor
Doorbell Button
Speaker
Plastic Cover
Light Sensor
Mounting Bracket
Security Screws
⑥
⑦
⑧
⑨
Greet Universal
Indoor Chime
1
What’s in the box:
2
Screwdriver &
Interchangeable
Bit
Interchangeable
Faceplate
(Only included in
select configurations)
Masonry
Drill Bit
Spare Security
Screws
Mounting Screws
& Anchors (x8)
Mounting Level
Quick Start Guide
Power Cable Power Adapter
Greet Universal
Quick Start Guide
Greet Universal /
Indoor Chime
IMPORTANT! Use the guides below to carefully plan out
your installation process. Read through the entire quick
guide before performing any permanent installation and
drilling.
You will need to connect your Indoor Chime to a nearby
power outlet using the provided power adapter. Please
see Figure 2.
You will need a hole between your interior and exterior
wall that is at least 0.8 inch in diameter. You will feed the
provided power cable through this hole to connect the
Indoor Chime and Greet Universal. Please see Figure 1.
Before you begin:
2Mounting your Greet Universal
3
Make sure that you have a strong WiFi connection at the
location of your Greet Universal. Visit
www.zmodo.com/support for advice on improving your
WiFi signal range.
Figure 2.
Indoor Chime installed on interior wall
Figure 3.
Greet Universal installed on exterior wall.
Indoor
Chime
Greet
Universal
Indoor
wall
Exterior
wall
provided
power
cable
Figure 1.
Indoor Chime connection to Greet Universal.
4
Drilling the power cable hole
Remove your existing doorbell button. There should be a
small hole in your wall when you remove your doorbell.
1
If you wish to install your Greet Universal at the location
of your existing doorbell, please follow the steps below to
drill the 0.8 inch hole for the power cable.
IMPORTANT! Before you begin, make sure that the
power to your doorbell is turned off. Check your circuit
breaker for a switch.
If you have never drilled through a wall before, please
visit YouTube for detailed tutorial videos.
Drill a 0.8 inch hole from the exterior of your wall through
the interior wall. Using a power drill and a long drill bit, drill
a 0.8 inch hole through your exterior wall until it penetrates
the interior wall. Make sure that you avoid the IMPORTANT:
wiring from your mechanical chime when drilling to avoid
shock hazards.
2
(Optional) Insert a rigid pipe through the hole. Insert a rigid
pipe through to the interior wall to make it easier to feed the
power cable through the wall. Grind it down until it is flush
with the wall.
3
Remove the mounting bracket from your chime. Take your
Indoor Chime out of the packaging and slide down to
remove the mounting bracket as shown below:
1
5
Mounting the Indoor Chime
Slide down
Mark and drill the appropriate holes in the wall for the
mounting bracket. Snap the provided level onto the
mounting bracket and align the bracket against the wall
where you would like to install your chime. Make sure that
the hole in the bracket lines up with the 0.8 inch hole that
you drilled in the first part of the installation. Using the
bracket as a guide, mark the wall with the four
corresponding holes for screws. Remove the mounting
bracket from the wall and detach the level. Drill four holes
slightly smaller than the wall anchors using the provided
drill bit.
2
6
Fasten the mounting bracket onto the wall. Gently tap the
wall anchors into the holes with a hammer until the
anchors are flush against the wall. Using the Philips tip for
the provided screwdriver and the provided screws, fasten
the bracket into place.
3
Feed the power cable through the 0.8 inch hole and
connect the cable to the back of the Indoor Chime. Feed
the included power cable through the 0.8 inch hole until
the other end is exposed from the exterior wall. Remove
the yellow protective cover from the end of the power
cable, and connect the cable to the port on the back of the
Indoor Chime.
4
7
Mounting the Greet Universal
Remove the mounting bracket and plastic cover from
your Greet Universal. Take your Greet Universal from the
packaging and slide down to remove the mounting
bracket, then pop off the plastic cover.
1
Attach the Indoor Chime to the mounting bracket. Mount
the Indoor Chime into the mounting bracket by pushing
firmly and sliding downwards as shown.
5
Slide down
Slide down
8
Mark and drill the appropriate holes in the wall for the
mounting bracket. Snap the provided level onto the
mounting bracket and align the bracket against the wall
where you would like to install your Greet Universal. Make
sure that the hole in the bracket lines up with the 0.8 inch
hole that you drilled in the first part of the installation.
Follow steps 2-3 from the Indoor Chime installation to
mount the bracket for the Greet Universal.
2
Connect the power cable to the Greet Universal and attach
the Greet Universal to the mounting bracket. Peel off the
yellow protective cover from the end of the power cable,
and connect it to the port on the back of the Greet
Universal. Push firmly and slide downward to fasten the
Greet Universal onto the mounting bracket.
3
Fasten the security screws and snap on the plastic cover.
Tighten the two security screws on the bottom of the Greet
Universal until secure, and snap the plastic cover onto the
Greet Universal.
4
9
Using the provided power adapter, power on the Indoor
Chime. Connect the included power adapter to the power
port on the bottom of the Indoor Chime, and plug in the
power adapter to a nearby power outlet to power on your
Greet Universal.
5
Table of contents
Other ZMODO Accessories manuals
