Zibro Laser FF 55 User manual

Laser FF 55

MANUEL D’UTILISATION

OPERATING INSTRUCTIONS

GEBRUIKSAANWIJZING

KULLANIM KILAVUZU

4OPERATING INSTRUCTIONS

Dear Sir, Madam,

Congratulations with your purchase of the Zibro, the number one brand among

movable heaters. You have purchased a first-class quality product, which will

serve you for many years to come. This, of course, provided you use the heater

correctly. Please read these Directions for Use first, to ensure maximum lifetime

for your Zibro.

Your heater comes with a 24-month manufacturer’s warranty on all defects in

material or workmanship.

Wewish you much warmth and comfort with your Zibro.

Yours sincerely,

PVG International B.V.

Customer Service Department

1READ THE DIRECTIONS FOR USE FIRST.

2IN CASE OF ANY DOUBT, CONTACT YOUR ZIBRO DEALER.

SUMMARY

Chapter 1: INSTALLATION

Chapter 2: OPERATION

Chapter 3: ERROR MASSAGES

Chapter 4: WARRANTY PROVISIONS

WHAT YOU NEED TO KNOW IN ADVANCE

THE RIGHT FUEL

Only use Class C1 paraffin fuel in accordance with BS2869: Part 2, or equivalent. Your Zibro heater has been

designed for use with high-quality water-free pure paraffin oil, such as Zibro Extra or Zibro Kristal. Only fuels

of this kind will ensure clean and proper burning. Lower quality fuel may result in:

Eincreased possibility of malfunctioning

Eincomplete burning

Ereduced heater lifetime

Esmoke and/or smells

Edeposits on the grid or mantle

Using the right fuel is therefore essential for safe, efficient, and comfortable use of your heater.

Always refer to your local Zibro dealer for the right fuel for your heater.

TIPS FOR SAFE USE

1Make surethat children are always aware of the presence of a burning heater.

2Position the front of the heater at a distance of minimum 1.5 metres from walls, curtains, and furniture.

3Do not use the heater in dusty rooms. You will not have optimum burning in such rooms. Do not use the

heater in the immediate surrounding of a bath, a shower or a swimming pool.

4Switch off the heater, before you leave or go sleeping. Unplug the heater as well, when you go away for

alonger period of time (e.g. holidays).

5Store and move fuel only in suitable tanks and jerrycans.

6Make sure that the fuel is not exposed to heat or extreme temperature changes. Always store the fuel in

acool, dry and dark place (sunlight will affect the quality).

7Never use the heater in places where harmful gasses or fumes may be present (e.g. exhaust gasses or

paint fumes).

8Bewarethat the grid of the heater becomes hot. If the appliance is covered there is a risk of fire.

9Use only in accordance with state and/or local regulations, ordinances and codes.

10 Make sure the heater is on a level surface during operation

11 Do not service or refuel heater while in operation or still hot.

12 Do not operate in areas exposed to flammable vapors or high duel level to avoid fire or explosion.

•The first time you ignite your heater it will smell like ’new’ for a short time.

•Store your fuel in a cool and dark place.

•Fuel has a limited shelf life. Start every heating season with renewed fuel.

•The right quality of fuel will be assured, when you use ZibroExtra or ZibroKristal for your

heater.

•If you change to another brand and/or type of parrafin oil, you must first finish up all the

remaining fuel in the heater.

☞

1. Introduction

This chapter contains all the relevant information,

specifically:

• Installation specifications

• List of installation tools

• Instructions for the installation of the Laser System

The heater can be installed at any location, on condi-

tion that there is full compliance with electrical, fuel

and emission regulations.

Beforeyou start installing the heating system (possibly

including electrical wiring and fuel supply equipment),

check the local building and fire safety regulations. The

requirements stipulated in these regulations must be

respected in order to guarantee a legally approved

installation and correct operation.

The heater was designed to be used to a

maximum altitude of 1000m above sea level.

Contact your dealer for the necessary

adjustments if you wish to use it at a higher

altitude.

2. Moving the heater

In addition to the space required for the heater, extra

room must be kept free for air circulation. We recom-

mend that you storefuel elsewhere. The Laser System

can be placed on any type of flooring (including fitted

carpets or other flammable materials) and operate

safely,unless fuel or fire safety regulations specify oth-

erwise. Check the gaps in the manner stipulated in the

instructions in the manual.

Recommended tool kit

1. Crosshead screwdriver

2. Steel tape measure

3. Felt-tip pen or pencil

4. Cement for exterior use

5. Electric drill (clockwise and anti-clockwise

recommended)

6. Hole cutting saw, jig saw or other tools suitable for

sawing a hole of 70~80 mm for the exhaust pipe

7. Long drill

8. Standard screwdrivers

9. Volt, Ohmmeter

10.Spirit level

11.Small range of self-tapping screws

12.Insulated screwdriver

13.Protective material for your floor

14.Container for fuel exhaust pipe

3. The electrical supply system

The electrical system must be protected from overloads

by an at least 5-Amperefuse or contact breaker.

Some installations (such as for use in mobile

homes) must be fitted with a permanent

connection to the household power circuits.

This must be done by a recognised

electrician.

Chapter 1, INSTALLATION

4. Wiring for the room temperature sensor

Atemperature sensor that can be fitted to a wall mea-

sures the room temperature in order to automatically

regulate the heating. The standard sensor wire is

approximately 2.5 m long.

The sensor may not be placed in a draught,

direct sunlight or the warm air flowing out

of the heater. This may cause incorrect

temperature indications.

5. Unpacking

Save all packaging materials for possible future trans-

portation.

A) Remove the cardboard (drilling) template and the

user’s manual from the packaging.

B) Remove the box with the installation kit from the

packaging.

C) Remove the heater from the packaging.

D) Remove the plastic bag containing the parts.

E) Remove the exhaust pipe from the bottom of the

box.

F) Check that all parts are present.

Only the standardfeed and exhaust system

is supplied with the heater.

Fig. 1-1: Gaps heater/exhaust pipe

Laser FF 55

More than 60 cm

Morethan 30 cm

Morethan 1.5 m

More than 30 cm

More than 10 cm

☞

Chapter 1, INSTALLATION

Fig. 1-2 Gaps heater/exhaust pipe

Fig. 1-1 (continued) gaps heater/exhaust pipe

Flammable object

Not less than 60 cm

Flammable object

Non-flammable

object

45°C

Not less than 30 cm

Exhaust pipe

Not less than 60 cm

Not less than 20 cm

Not less

than 45 cm

Not less

than 45 cm

Frontal obstruction

45 cm

or more

50 cm

or more

Snow-covered surface or ground

Important: The gap with the ground must be enlarged in areas

subject to heavy snowfall. Important: A windbreaker may be necessary in open areas that

are subjected to strong winds.

Extension tube of

max. 2.5 metres Must be higher

Snow

Strong wind

Distance from

exhaust pipe to

windbreaker mini-

mum 45 cm

Not less

than

45 cm Windbreaker

☞

After using the installation template as a guide for the

drilling of the hole for the exhaust pipe, the Laser can

be installed normally, according to the procedure in the

illustration.

If the template is lost or the heater has to be moved,

these are the dimensions and locations of the holes for

the fuel pipe and exhaust pipe.

Do not remove any components from the

heater. Always contact your dealer if repairs

are required.

If the electricity cable is damaged, this may

only be replaced with type H05 VV-F and by

a recognised installer.

Chapter 1, INSTALLATION

Laser FF 55

Fig. 1-3 Template

Achterkant van de

kachel

314 cm.

108 mm

Back of the heater

Centre of the

feed-through

component

Chapter 1, INSTALLATION

Standard installation parts

The following list of standard installation parts is sup-

plied with your heater. It may be necessary to order

extra parts from your Zibro dealer if other installation

methods are required.

Wall hooks (2 set) Pipe holder (1)

Pipe lock (1) Exhaust pipe (1)

(3)

Chapter 1, INSTALLATION

Right-angled exhaust pipe bend (1) Right-angled air hose (2)

Flexible air hose (1)

Hose clip (2)

Manual fuel pump (1) Fuel cap cover (1)

Table of contents

Popular Heater manuals by other brands

oventrop

oventrop Regucor Series quick start guide

Blaze King

Blaze King CLARITY CL2118.IPI.1 Operation & installation manual

ELMEKO

ELMEKO ML 150 Installation and operating manual

BN Thermic

BN Thermic 830T instructions

KING

KING K Series Installation, operation & maintenance instructions

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Installation instructions and owner's manual

Well Straler

Well Straler RC-16B user guide

EUROM

EUROM 333299 instruction manual

Heylo

Heylo K 170 operating instructions

Eterna

Eterna TR70W installation instructions

Clarke

Clarke GRH15 Operation & maintenance instructions

IRSAP

IRSAP The Radiator Company Ovali Fitting instructions

Empire Heating Systems

Empire Heating Systems WCC65 Installation and owner's instructions

Wetekom

Wetekom 92 86 43 Original instructions

Desa

Desa SPC170-F owner's manual

Watlow

Watlow Watrod Electric Tubular Heaters Specifications

Haverland

Haverland ECO-DRY GPS Series Instruction & installation manual

Stelpro

Stelpro ASILVC2060 Series user guide