Zephyr AIN-M80AWX Quick start guide
www.zephyronline.com
Wave
AWA-M90AWX
AWA-M90ABX
Incline
AIN-M80AWX
AIN-M80ASX
RANGE HOOD - Installation and use instructions
ENGLISH........................................3
FRANÇAIS...................................33
- 6 -
LIST OF MATERIALS
Incline
- Zephyr blower sold separately
- Non-ducted recirculating kit sold separately
- Duct cover accessory sold separately
Box Cover (box
marked “120 VAC
Input”)
Box marked “120
VAC Input”
Led
Mesh Filter
Hardware Packet
Remote Blower Collar with
Damper (External motor)
Remote Blower Box Cover
Remote Blower Box
Electrical System Box
Remote Blower Wiring Extension
Remote Blower Wiring Harness
- 7 -
LIST OF MATERIALS
Wave
- Zephyr blower sold separately
- Non-ducted recirculating kit sold separately
- Duct cover accessory sold separately
Box Cover (box
marked “120 VAC
Input”)
Box marked “120
VAC Input”
Led
Mesh Filter
Hardware Packet
Remote Blower Collar with
Damper (External motor)
Remote Blower Box Cover
Remote Blower Box
Electrical System Box
Remote Blower Wiring Extension
Remote Blower Wiring Harness
- 8 -
DUCTING CALCULATION SHEET
Maximum Duct Length:
For satisfactory air movement, the total duct length
should not exceed 100 equivalent feet.
- 9 -
HOOD SPECIFICATIONS
Incline
- 10 -
HOOD SPECIFICATIONS
Wave
- 11 -
WIRING DIAGRAM
- 16 -
INSTALLING THE DUCTWORK:
INTERNAL BLOWER
NOTE: To reduce the risk of fire, use only
metal ductwork.
1. Decide where the ductwork will run
between the hood and the outside.
2. A straight, short duct run using a minimum
6” round duct will allow the hood to perform
most efficiently.
3. Long duct runs, elbows, and transitions will
reduce the performance of the hood. Use
as few of them as possible.
4. Install a roof or wall cap. Connect round
metal ductwork to cap and work back
towardshoodlocation.Useducttapetoseal
the joints between ductwork sections
(Fig.7). FIG. 7
ROOF CAP
OPTIONAL
DUCT COVER
HOOD
22” MINIMUM ABOVE COOKING
SURFACE
WALL
CAP
6” ROUND DUCT
FIG. 8
FIG. 9
Model Incline
Model Wave
FIG.10
Model Wave
PREPARE FOR INSTALLATION
ModelIncline
Remove the (2) screws and take off the front
panel. See Fig. 8.
Model Wave
1. Open the upper front glass; remove the
lower glass unscrewing (2) screws and
moving it upward (Fig.9).
2. Remove the metal panel unscrewing (6)
screws. Fig. 10.
- 17 -
INSTALLATION INTERNAL
BLOWER
NOTE: The following instructions are for
installingtheinternalblower only.
Installthisrangehoodonlywithinternalblower
model CBI-290A or CBI-600A.
1. Remove the knockout (B). Fig. 13.
2. Fix the internal blower with (4) mounting
screws (supplied with the internal blower).
Fig. 13.
(4) MOUNTING SCREWS
(Supplied with the motor)
CHOOSE AIR OUTLET
LOCATION
The hood is supplied with upper air outlet;
but you can let the air out the back, turning
the motor plate.
Rotation of the motor plate:
1.Remove the motor plate unscrewing (6)
screws (Fig.11).
2.Rotate the motor plate and re-fix in the new
position (Fig.12).
In the installation with internal blower, use
the rond knockout (B);
in the installation with remote or In-line
blower, use the other knockout (A).
FIG.11
FIG.12
FIG.13
KNOCKOUT
(B) KNOCKOUT
(A)
KNOCKOUT
(B)
- 18 -
REMOTE BLOWERS (EXTERNAL AND IN-LINE)
CAUTION: To reduce risk of fire and electric shock, install this range hood only with External
Blower Model CBE-1000, and In-Line Blower Model PBN-1000A. Other blowers cannot be
substituited.
INSTALLING THE DUCTWORK: REMOTE BLOWER
NOTE: To reduce the risk of fire, use only metal ductwork.
1. Choose the location where the External Blower or In-Line Blower will be mounted. See
illustrations below for mounting location suggestions and restrictions.
2. A straight, short duct run using a minimum 8” round duct will allow the hood to perform
most efficiently.
3. Long duct runs, elbows and transitions will reduce the performance of the hood. Use as
few of them as possible. Larger ducting may be required for best performance with long
duct runs.
4. After the Exterior or In-Line Blower has been installed, connect round metal ductwork
and work back towards the hood location. Use duct tape to seal joints between ductwork
sections.
Roof Pitch w/
Flashing & Cap
in-line
blower
(blower
housing)
external blower
Attic or crawl space
(blower
housing)
Roof Pitch w/
Flashing & Cap
in-line
blower
(blower
housing)
external blower
Attic or
crawl
space
(blower
housing)
Other manuals for AIN-M80AWX
1
This manual suits for next models
1
Table of contents
Other Zephyr Ventilation Hood manuals
Zephyr
Zephyr Ombra ZOM-E30ABS Installation guide
Zephyr
Zephyr Titan AK7636AS Installation guide
Zephyr
Zephyr Lux ALU-E43CSX Installation guide
Zephyr
Zephyr ZPY-E30AB Installation guide
Zephyr
Zephyr Verona ZVO-E30AG Installation guide
Zephyr
Zephyr AK0710 Installation guide
Zephyr
Zephyr ZML-M90S/G Installation guide
Zephyr
Zephyr Trapeze CTP-E48BSX Installation guide
Zephyr
Zephyr Roma Pro Wall ZRP-E36AS Installation guide
Zephyr
Zephyr ALU-E43ASX User manual
Zephyr
Zephyr Venezia ZVE-E30AS User manual
Zephyr
Zephyr Spruce AK9834BS Installation guide
Zephyr
Zephyr Tidal II AK7400AS Installation guide
Zephyr
Zephyr Trapeze CTP-E 48SX User manual
Zephyr
Zephyr Siena ZSI-E30AS Installation guide
Zephyr
Zephyr Essentials Anzio ZAZ-M90AS Installation guide
Zephyr
Zephyr Tidal I Installation guide
Zephyr
Zephyr AK7048BS Installation guide
Zephyr
Zephyr Monsoon Mini Installation guide
Zephyr
Zephyr VALINA ZVA-M60AS290 User manual
