Zephyr AK0710 Installation guide

www.zephyronline.com

Use, Care and Installation Guide

Tempest I , II

Stainless Steel

Backsplash

AK0710 - 30”

AK0716 - 36”

AK0712 - 42”

AK0718 - 48”

FEB07.0201

Table of Contents

LIST OF MATERIALS —————————–- 2

SPECIFICATION ———————————— 3

INSTALLATION ————————————- 4,5

CLEANING AND

CONTACT INFORMATION ———————— 6

1

List of Materials

1 - Upper Section

1 - Lower Section

2 - Wire Racks

1 - Hardware Packet

2 - Retaining Clips

4 - Hinge Clips

6 - 7/16” Carriage Head Bolts

8 - 5/8” Philips Head Wood Screw

6 - Carriage Head Bolt Nuts

Note: If any parts are missing, please call

1-888-880-8368 for replacements.

2

Specifications

3

Installation

1. Mark a level line on the wall at 16” below bottom of hood.

2. Position the lower section of backsplash (flat part with flange on top) on the wall.

Center it side to side and mark the top and bottom holes. Remove the lower section from

the wall.

3. If installing onto drywall only and not onto studs, insert wall anchors (we recommend EZ

anchors) into the marked holes. If installing onto studs, attach screws without EZ anchors.

4. Attach lower section of backsplash to wall with screws provided.

5. Position upper section of backsplash by engaging its flange with the lower section. Push up

to fully engage flanges*, center it side to side and mark the location of the mounting holes.

Remove the upper section from drywall and install wall anchors into marked holes.

5b.If hood is already installed, attach wall anchors into the (3) holes from inside the hood at the

bottom. These are the holes which the upper section will line up with and mount to the wall.

6. Insert retaining clips and hinge clips to the upper section. The retaining clips go in the top

top two openings and the hinge clips go in the bottom four openings. (see diagram, page 4)

Fasten and tighten nuts to the clips on back of the upper section with the provided

hardware.

7. Attach upper section to wall with screws provided. If hood is already installed, Insert the top

2” lip of the upper section behind the bottom of the hood and line up the holes with the (3)

holes at the bottom of the hood. Insert screws into holes and fasten upper section to wall.

*note: in some installations, the flanges will not fully engage in the final install. This is fine

since the weight of the upper section will rest against the bottom section.

4

Installation

1. For the warming plate option; snap the wire shelves into hinge clips

on the backsplash as shown in the left side shelf diagram.

2. For the spice rack option; attach shelf to hinge clips, as

show in the right side shelf diagram, then rotate shelf upwards and

secure with retaining clip.

5

Cleaning and Contact Information

Cleaning of the backsplash should be done frequently to preserve the

life of the stainless steel. Cleaning should typically be done once or

twice a month depending on your cooking habits.

When cleaning, use a non abrasive cleaner, do not use “orange”

cleaner. Abrasive cleaners may scratch the surface and discolor the

stainless steel. To clean the wire racks, soak them in soapy water.

DO NOT place in a dishwasher as this may discolor the wire racks.

You may also polish the stainless steel by using stainless steel polish.

Make sure when polishing to go along with the grain of the backsplash.

Zephyr Corporation

395 Mendell Street

San Francisco, CA 94124

1-888-880-8368

6

This manual suits for next models

3

Table of contents

Other Zephyr Ventilation Hood manuals

Zephyr

Zephyr Willow AK8800AG Technical manual

Zephyr

Zephyr Pyramid ZPY-E30S Installation guide

Zephyr

Zephyr ZPA-M90S Installation guide

Zephyr

Zephyr Tidal I AK7300AS Installation guide

Zephyr

Zephyr ZMO-E30BS Installation guide

Zephyr

Zephyr Gust AK7100AS Installation guide

Zephyr

Zephyr Verona ZVO-E30AG Installation guide

Zephyr

Zephyr AK9028AS Installation guide

Zephyr

Zephyr Verona ZVO-E30BG Installation guide

Zephyr

Zephyr ESSENTIALS Monsoon I AK9228AS290 Installation guide

Zephyr

Zephyr Monsoon Mini Installation guide

Zephyr

Zephyr Venezia ZVE-E30BS Installation guide

Zephyr

Zephyr Monsoon II Installation guide

Zephyr

Zephyr MESA DME-M90ASSX User manual

Zephyr

Zephyr ZSA-E30CB Installation guide

Zephyr

Zephyr Typhoon AK2100CS Installation guide

Zephyr

Zephyr Ombra ZOM-E30ABS Installation guide

Zephyr

Zephyr ES1-E30AB Installation guide

Zephyr

Zephyr Siena ZSI-E30AS Installation guide

Zephyr

Zephyr ALU-E43BSX Installation guide

Zephyr

Zephyr Slope ESL-M90AS Installation guide

Zephyr

Zephyr ZRO-E30BS User manual

Zephyr

Zephyr ZRC-7000B User manual

Zephyr

Zephyr Brisas BMI-E36AG Installation guide

Popular Ventilation Hood manuals by other brands

emmeti

emmeti RECUPA MED A-140 Installation and use manual

Nibe

Nibe F135 user manual

Kuppersberg

Kuppersberg INTRO 60 Technical Passport

Hisense

Hisense MH6INBG manual

Miele

Miele DA 1255 Operating and installation instructions

Broan

Broan 46000 Specification sheet

GE

GE Profile PV977 Owner's Manual & Installation Instructions

FALMEC

FALMEC FFRIA24W5FS Instruction booklet

Whirlpool

Whirlpool RH2600XL-1 SERIES installation instructions

Küppersbusch

Küppersbusch DX ISLA instruction manual

ETNA

ETNA AV360RVS Instructions for use

JUNO

JUNO JDF603E6 installation manual

Miele

Miele DA 6708 D Operating and installation instructions

Tricity Bendix

Tricity Bendix LE 150 Installation & operating instructions

AEG

AEG X68163BV1 user manual

AEG

AEG 125 D operating instructions

Smeg

Smeg KSEV97X instruction manual

Nibe

Nibe S Series Installer manual