YASKAWA VS MINI J7 User manual
YASKAWA
YA S K A WA
MANUAL NO. TOE-S606-12.1G
Upon receipt of the product and prior to initial operation, read these instructions
thoroughly and retain them for future reference.
VS mini J7 Series
INSTRUCTION MANUAL
COMPACT GENERAL-PURPOSE INVERTER
1
PREFACE
Yaskawa’s VS mini J7 (hereinafter called VS mini) is a small and simple
Inverter; as easy to use as a contactor. This instruction manual describes
installation, maintenance, inspection, troubleshooting, and specifications of
the VS mini. Read this instruction manual thoroughly before operation.
YASKAWA ELECTRIC CORPORATION
General Precautions
• Some drawings in this manual are shown with protective covers or shields
removed in order to show detail with more clarity. Make sure all covers and
shields are replaced before operating the product.
• This manual may be modified when necessary because of improvements to
the product, modifications, or changes in specifications.
Such modifications are indicated by revising the manual number.
• To order a copy of this manual, or if your copy has been damaged or lost,
contact your Yaskawa representative.
• Yaskawa is not responsible for any modification of the product made by the
user, since that will void the guarantee.
2
NOTATION FOR SAFETY PRECAUTIONS
Read this instruction manual thoroughly before installation, operation, mainte-
nance, or inspection of the VS mini. In this manual, safety precautions are classi-
fied as either warnings or cautions and are indicated as shown below.
Indicates a potentially hazardous situation which, if not avoided, may result in
death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, may result in
minor or moderate injury or damage to equipment.
It may also be used to alert against unsafe practices.
Even items classified as cautions may result in serious accidents in some situa-
tions. Always follow these important precautions.
: Indicates information to insure proper operation.
WARNING
CAUTION
NOTE
3
PRECAUTIONS FOR UL/cUL MARKING
• Do not connect or disconnect wiring, or perform signal checks while the
power supply is turned ON.
• The Inverter internal capacitor is still charged even after the power supply
is turned OFF. To prevent electric shock, disconnect all power before ser-
vicing the Inverter, and then wait at least one minute after the power sup-
ply is disconnected. Confirm that all indicators are OFF before
proceeding.
• Do not perform a withstand voltage test on any part of the Inverter. The
Inverter is an electronic device that uses semiconductors, and is thus vul-
nerable to high voltage.
• Do not remove the Digital Operator or the blank cover unless the power
supply is turned OFF. Never touch the printed circuit board (PCB) while
the power supply is turned ON.
• This Inverter is not suitable for use on a circuit capable of delivering more
than 18,000 RMS symmetrical amperes, 250 V maximum (200 V Class
Inverters) or 18,000 RMS symmetrical amperes, 480 V maximum (400 V
Class Inverters).
PRECAUTIONS FOR CE MARKINGS
• Only basic insulation to meet the requirements of protection class 1 and
overvoltage category II is provided with control circuit terminals.
Additional insulation may be necessary in the end product to conform to
CE requirements.
• For 400 V class Inverters, make sure to ground the supply neutral to con-
form to CE requirements.
• For conformance to EMC directives, refer to the relevant manuals for the
requirements.
Document No. EZZ008389 for Japanese version,
Document No. EZZ008390 for English version
• Use 75°C copper wire or equivalent.
Low voltage wires must be wired with Class I Wiring.
CAUTION
4
RECEIVING THE PRODUCT
MOUNTING
(Ref. page)
• Do not install or operate any Inverter that is
damaged or has missing parts.
Failure to observe this caution may result in injury or
equipment damage.
19
(Ref. page)
• Lift the Inverter by the heatsinks. When moving
the Inverter, never lift it by the plastic case or the
terminal cover.
Otherwise, the main unit may fall and be damaged.
21
• Mount the Inverter on nonflammable material
(i.e., metal).
Failure to observe this caution may result in a fire.
21
• When mounting Inverters in an enclosure, install
a fan or other cooling device to keep the intake
air temperature below 50°C.
Overheating may cause a fire or damage the Inverter.
21
• The VS mini generates heat. For effective cool-
ing, mount it vertically.
Refer to the figure in Mounting Dimensions on
page 22.
22
CAUTION
CAUTION
5
WIRING
(Ref. page)
• Only begin wiring after verifying that the power
supply is turned OFF.
Failure to observe this warning may result in an elec-
tric shock or a fire.
24
• Wiring should be performed only by qualified
personnel.
Failure to observe this warning may result in an elec-
tric shock or a fire.
24
• When wiring the emergency stop circuit, check
the wiring thoroughly before operation.
Failure to observe this warning may result in injury.
24
• For 400 V class, make sure to ground the sup-
ply neutral.
Failure to observe this warning can result in an elec-
tric shock or a fire.
29
• Always ground the ground terminal accord-
ing to the local grounding code.
Failure to observe this warning may result in an elec-
tric shock or a fire.
29
• When the 3-wire sequence is set, do not make
the wiring for the control circuit unless the multi-
function input terminal parameter is set.
Failure to observe this warning may result in injury.
70
WARNING
6
(Ref. page)
• Verify that the Inverter rated voltage coincides
with the AC power supply voltage.
Failure to observe this caution may result in personal
injury or a fire.
• Do not perform a withstand voltage test on the
Inverter.
Performing withstand voltage tests may damage
semiconductor elements.
• Always tighten terminal screws of the main cir-
cuit and the control circuits.
Failure to observe this caution may result in a mal-
function, damage, or a fire.
24
• Never connect the AC main circuit power supply
to output terminals U/T1, V/T2, or W/T3.
The Inverter will be damaged and the guarantee will
be voided.
24
• Do not connect or disconnect wires or connec-
tors while power is applied to the circuits.
Failure to observe this caution may result in injury.
• Do not perform signal checks during operation.
The machine or the Inverter may be damaged.
CAUTION
7
OPERATION
(Ref. page)
• Only turn ON the input power supply after con-
firming that the front cover, top cover, and bot-
tom cover are in place. Do not remove the
covers while current is flowing.
Failure to observe this warning may result in an elec-
tric shock.
• Never operate the Digital Operator or DIP
switches with wet hands.
Failure to observe this warning may result in an elec-
tric shock.
• Never touch the terminals while current is flow-
ing, even if the Inverter is stopping.
Failure to observe this warning may result in an elec-
tric shock.
• When the fault retry function is selected, stand
clear of the Inverter or the load. The Inverter
may restart suddenly after stopping.
(Construct the system to ensure safety, even if the
Inverter should restart.) Failure to observe this warn-
ing may result in injury.
60
• When continuous operation after power recov-
ery is selected, stand clear of the Inverter or the
load. The Inverter may restart suddenly after
stopping.
(Construct the system to ensure safety, even if the
Inverter should restart.) Failure to observe this warn-
ing may result in injury.
56
• The Digital Operator stop button can be dis-
abled by a setting in the Inverter. Install a sepa-
rate emergency stop switch.
Failure to observe this warning may result in injury.
WARNING
8
(Ref. page)
• If an alarm is reset with the operation signal ON,
the Inverter will restart automatically. Reset an
alarm only after verifying that the operation sig-
nal is OFF.
Failure to observe this warning may result in injury.
32
• When the 3-wire sequence is set, do not make
the wiring for the control circuit unless the multi-
function input terminal parameter is set.
Failure to observe this warning may result in injury.
70
(Ref. page)
• Never touch the heatsinks, which can be
extremely hot.
Failure to observe this caution may result in harmful
burns to the body.
• It is easy to change operation speed from low to
high. Verify the safe working range of the motor
and machine before operation.
Failure to observe this caution may result in injury
and machine damage.
• Install a holding brake separately if necessary.
Failure to observe this caution may result in injury.
• If using an Inverter with an elevator, take safety
measures on the elevator to prevent the eleva-
tor from dropping.
Failure to observe this caution can result in personal
injury.
• Do not perform signal checks during operation.
The machine or the Inverter may be damaged.
WARNING
CAUTION
9
MAINTENANCE AND INSPECTION
• All the constants set in the Inverter have been
preset at the factory. Do not change the settings
unnecessarily.
The Inverter may be damaged.
33
(Ref. page)
• Never touch high-voltage terminals on the
Inverter.
Failure to observe this warning may result in an elec-
tric shock.
• Disconnect all power before performing mainte-
nance or inspection, and then wait at least one
minute after the power supply is disconnected.
Confirm that all indicators are OFF before pro-
ceeding.
If the indicators are not OFF, the capacitors are still
charged and can be dangerous.
• Do not perform withstand voltage test on any
part of the VS mini.
The Inverter is an electronic device that uses semi-
conductors, and is thus vulnerable to high voltage.
• Only authorized personnel should be permitted
to perform maintenance, inspection, or parts
replacement.
(Remove all metal objects (watches, bracelets, etc.)
before starting work.)
(Use tools which are insulated against electric
shock.)
Failure to observe these warnings may result in an
electric shock.
93
CAUTION
WARNING
Other manuals for VS MINI J7
3
This manual suits for next models
19
Table of contents
Other YASKAWA Inverter manuals
YASKAWA
YASKAWA XGI 1000-65/65 Operating instructions
YASKAWA
YASKAWA Varispeed-676 User manual
YASKAWA
YASKAWA SOLECTRIA XGI 1500-DCG Series Operating instructions
YASKAWA
YASKAWA VS mini C Series User manual
YASKAWA
YASKAWA Varispeed f7 User manual
YASKAWA
YASKAWA PVI 60TL User manual
YASKAWA
YASKAWA XGI 1000-65/65 Operating instructions
YASKAWA
YASKAWA Varispeed G7 Series User manual
YASKAWA
YASKAWA Varispeed L7 User manual
YASKAWA
YASKAWA SOLECTRIA XGI 1500-250/250-600 Operating instructions
YASKAWA
YASKAWA VS MINI J7 series User manual
YASKAWA
YASKAWA VARISPEED-616G5 User manual
YASKAWA
YASKAWA PVI 23 TL User manual
YASKAWA
YASKAWA CIMR-F7A User manual
YASKAWA
YASKAWA VS mini C Series User manual
YASKAWA
YASKAWA Solectria PVI 25TL-480-R Operating instructions
YASKAWA
YASKAWA VS MINI J7 User manual
YASKAWA
YASKAWA VS MINI J7 User manual
YASKAWA
YASKAWA VS-606V7 Series User manual
YASKAWA
YASKAWA Varispeed G7 User manual
