Yamaha NS-C103 User manual

Table of contents

Other Yamaha Speakers System manuals

Popular Speakers System manuals by other brands

JVC

JVC CA-MXK5R instructions

LG

LG NB4532B owner's manual

JVC

JVC CA-FSH100 instructions

5Core

5Core Pro Series Operation manual

EAW

EAW MQV1394e Specifications

Lynx

Lynx GXR-LA10A user manual

iLive

iLive ITB066B user guide

RDX

RDX QuickStation 4 product manual

Electro-Voice

Electro-Voice S-122 Specifications

Sven

Sven SPS-619 GOLD Operation manual

Pioneer

Pioneer CS-7070 instruction manual

EAW

EAW UB82e Technical specifications

Sondpex

Sondpex Active Speaker System and Digital Music... User manual and installation instructions

JVC

JVC NX-PN7 instructions

Marshall Amplification

Marshall Amplification AR-DM61-BT user manual

SE Audiotechnik

SE Audiotechnik I-LINE manual

Gemini

Gemini WRX-843 Series user manual

TCL

TCL 6100 Series user manual

NS-C103

Thank you for selecting this Yamaha NS-C103 speaker system.

PRECAUTIONS

Read these precautions carefully before using your speaker.

●Any time you note distortion, reduce the volume control on

your amplifier to a lower setting. Never allow your amplifier to

be driven into “clipping”. Otherwise the speaker may be

damaged.

●When using an amplifier with a rated output power higher than

the nominal input power of the speaker, care should be taken

never to exceed the speaker’s maximum input.

●Do not attempt to clean the speaker with chemical solvents as

this might damage the finish. To clean, wipe with a dry, soft

cloth.

●To prevent the enclosure from warping or discoloring, do not

place the speaker where it is exposed to direct sunlight or

excessive humidity.

●Do not place the speaker where it is liable to be knocked over

or struck by falling objects. Stable placement will also ensure

better sound performance.

●Placing the speaker on the same shelf or rack as the turntable

can result in feedback.

●Secure placement or installation is the owner’s

responsibility.

YAMAHA shall not be liable for any accident caused by

improper placement or installation of the speaker.

BEFORE MAKING CONNECTIONS, MAKE SURE THAT THE

AMPLIFIER IS SWITCHED OFF.

■CONNECTIONS

●Connect the push-type input terminals at the rear of the

speakers to the speaker output terminals of your amplifier with

the provided speaker cables.

●One side of the speaker cable is red and the other side is

black. Connect the (+) terminals on both the amplifier and the

speakers using this red side. Connect the (–) terminals on both

components using the black side of the cable. If connected

with reversed polarity, the sound will be unnatural and lack

bass.

Procedures:

➀Press the tab on the terminal down, as shown in the figure.

➁Insert the bare wire end properly into the terminal hole.

[Remove approx. 10 mm (3/8”) insulation from the speaker

cable.]

➂Remove your finger from the tab to allow it to lock snugly on

the cable’s wire end.

➃Check the connection by lightly pulling the cable at the

terminal.

Note

Do not let the bare speaker wires touch each other as this

could damage the speaker and/or the amplifier.

CONNECTION TO YOUR AMPLIFIER

Natural Sound Center Speaker System

Press

tab Center speaker output

terminals of the amplifier

Red

NS-C103

Black

Red

Red Red

Amplifier

Place the speaker on top of the TV or on the floor under the TV

or inside the TV rack in a stable position.

When placing the speaker on top of the TV, to prevent the

speaker from falling down, put the provided slip-prevention pads

at two points on the bottom of the speaker where the speaker

touches the surface of the TV.

SPECIFICATIONS

Type .......................2-way 3-speaker bass-reflex speaker system

Magnetic-shielding type

Speaker Unit................................................8 cm cone woofer x 2

2.2 cm semi-dome tweeter

Nominal Impedance...........................................................6 ohms

Frequency Response............................................65 Hz – 20 kHz

Nominal Input Power..............................................................40W

Maximum Input Power .........................................................120W

Sensitivity.....................................................................89 dB/W·m

Dimensions (WxHxD)....................................435 x 100 x 230 mm

(17-1/8” x 4” x 9-1/16”)

Weight.............................................................2.0 kg (4 lbs. 6 oz.)

Accessories..............................................Speaker cable (4m) x 1

Slip-prevention pad x 2

* Specifications subject to change without notice due to product

improvements.

* Care should be taken not to exceed the input power values

noted above.

PLACING THE SPEAKER

Printed in China V 228310

12

Speaker on TV

TV set

Speaker inside

TV rack

Slip-prevention

pad

Notes

• Do not place the speaker on top of the TV whose area is

smaller than the bottom area of the speaker. If placed,

the speaker may drop, causing a personal injury.

• Though this speaker is a magnetic shielding type, there

may be some influence on a TV picture depending on the

type of TV or the placement of the speaker. In such a

case, place the speaker apart from the TV so that there is

no influence on TV picture.