Yaesu FT-301D User manual
Mod-VFO Drehrichtung_en.docx January 28, 2019, © Elcon, Switzerland Seite 2 / 7
Table of Comments
1Introduction ..................................................................................................................................... 3
2Changing the direction of rotation of the variable capacitor ........................................................... 4
2.1 Removing the spreaders in the VFO variable capacitor ........................................................ 4
2.2 Mechanical adjustment of the VFO variable capacitor........................................................... 5
2.3 Functional test........................................................................................................................ 6
3Changing the direction of rotation on the CALIB knob ................................................................... 6
4Disclaimer of liability ....................................................................................................................... 7
Important! Advices or tips for the correct function.
Caution! The instructions must be observed carefully.
Mod-VFO Drehrichtung_en.docx January 28, 2019, © Elcon, Switzerland Seite 3 / 7
1 Introduction
Normally you are used to turning the VFO knob clockwise increasing the frequency and vice
versa. With the FT-301D it is just the other way around and therefore very unusual.
This is due to the frequency conditioning of the FT-301.
Figure 1
As shown in Figure 1, the VFO frequency is subtracted from the crystal frequencies for the
different bands (Band Crystal). Thus, the VFO frequency runs in opposite direction to the
premixer frequency and thus also to the transmit frequency (Tx frequency).
Figure 2
The variable capacitor of the VFO is designed in such a way that the rotor plates turn out
clockwise and thus the capacity decreases -> the frequency of the VFO increases -> the Tx
frequency decreases.
As shown in Figure 2, the fiber glass spreaders on the two rotor plate packs prevent them
from being turned counterclockwise beyond the maximum capacity. However, this would be
absolutely necessary to reverse the frequency to the direction of rotation.
Spreader
Mod-VFO Drehrichtung_en.docx January 28, 2019, © Elcon, Switzerland Seite 4 / 7
The American amateur radio friend David, N0EDS, had the great idea to remove the two
spreaders so that the variable capacitor could be rotated freely through 360°.
The following description shows how the modification is carried out.
2 Changing the direction of rotation of the variable capacitor
2.1 Removing the spreaders in the VFO variable capacitor
Remove the four screws and the VFO cover.
Remove very carefully, without bending the rotor plate of the variable capacitor VC801,
both fiber glass spreaders with a small side cutter.
Figure 3
Place the device upright in front of you so that you can work well on the rotor plates.
Cover the lower part of the variable capacitor with a cloth to prevent filings from entering
the unit. (see Figure 4).
Figure 4
Carefully deburr all ends of the rotor plates with a needle file on the side where you have
removed the spreaders.
Mod-VFO Drehrichtung_en.docx January 28, 2019, © Elcon, Switzerland Seite 5 / 7
Under no circumstances should the rotor and stator plates touch each other!
Remove the cloth carefully so that no metal chips fall into the device.
Clean the capacitor between the plates with a contact spray so that there are no more
aluminum filings inside.
2.2 Mechanical adjustment of the VFO variable capacitor
Turn the unit, so that the open variable capacitor is easily accessible from above and the
tuning knob at the front.
Loosen (do not unscrew!) the two grub screws of the gear wheel on the axis of the rotary
capacitor. The tuning knob must be turned slightly, as both screws are not accessible at
the same time).
Figure 5
Position the variable capacitor by hand so that the rotor plates are fully turned in
(maximum capacity of the variable capacitor), see Figure 6).
Figure 6
Turn the tuning knob clockwise to the right stop. The variable capacitor must not rotate,
otherwise you have not loosened the grub screws enough.
Mod-VFO Drehrichtung_en.docx January 28, 2019, © Elcon, Switzerland Seite 6 / 7
In this position tighten the grub screw accessible from above.
Turn the tuning knob counterclockwise until you see the second grub screw and can
tighten this one too.
2.3 Functional test
Turn on your transceiver. Set the receiver in the 20m band, USB with "Tune" to maximum
noise in the speaker.
Check by slowly turning the VFO knob whether you can hear the noise over the entire
tuning range without interruption.
If the noise suddenly decreases at any position of the VFO knob, the rotor plates of the
variable capacitor are touching the stator. In this case, check the capacitor carefully with a
magnifying glass.
3 Changing the direction of rotation on the CALIB knob
Turn the unit upside down so that the underside faces upwards.
Solder off the two resistors R14 (1kΩ) and R15 (3.3kΩ) from the CALIB potentiometer
VR6 (5kΩ), see Figure 7 .
Figure 7
Solder the two resistors R14 (1kΩ) and R15 (3.3kΩ) in the swapped positions to the
CALIB potentiometer VR6 (5kΩ), see Figure 8
Figure 8
Mod-VFO Drehrichtung_en.docx January 28, 2019, © Elcon, Switzerland Seite 7 / 7
4 Disclaimer of liability
Any actions based on the information contained in this document are taken at the user's own
responsibility. Any liability is excluded, both for direct and indirect damages and
consequential damages that may arise in connection with the use of the information
contained in this document.
Table of contents
Other Yaesu Transceiver manuals
Yaesu
Yaesu FT-75B User manual
Yaesu
Yaesu FTDX 1200 Series Product guide
Yaesu
Yaesu FT-73R User manual
Yaesu
Yaesu FT-4XR User manual
Yaesu
Yaesu FT-710 User manual
Yaesu
Yaesu FT-530 User manual
Yaesu
Yaesu FT1DR User manual
Yaesu
Yaesu FTdx5000 Series User manual
Yaesu
Yaesu VX-120 Series User manual
Yaesu
Yaesu FT-757GX II User manual
Yaesu
Yaesu VX-8DR User manual
Yaesu
Yaesu FT-980 User manual
Yaesu
Yaesu FT-8800R Assembly instructions
Yaesu
Yaesu FT-902DM User manual
Yaesu
Yaesu FT-712RH User manual
Yaesu
Yaesu FTDX-9000MP User manual
Yaesu
Yaesu FT-707 User manual
Yaesu
Yaesu FTM-100DE User manual
Yaesu
Yaesu FT-891 User manual
Yaesu
Yaesu Mark-V FT-1000MP Installation guide
