XtendLan DPC-511 User manual

DPC-511

Door station

User’s Guide

1. Introductions

Door Station is a unit installed on the entrance of a building, which used to call a user in a

apartment, and control the electronic lock opening.

To call the user, press a button with a associated nameplate of the user; then the user will press the

Unlock button on the monitor to open the door for the visitor if she/he is accepted.

The Camera angle can be adjusted to coordinate the install position of the Door Station

2. Parts and functions

3. Terminals

• +12V: 12VDC power output

.• LK-(GND): power ground.

• LK+(COM): electronical load activation relay contact common

.• NO.: electronical load activation relay normally open contact

• EB+: Exit button.

• EB-: Exit button

• T/R-: USB-RS485 communication terminal negative

.• T/R+: USB-RS485 communication terminal positive

.• SET: DIP switches for system configurations.

• PA: program buttonA(refer to program section)

.• PB: program button B.(refer to program section)

.•Power (P-,P+): DC 18V

DIP1

DIP2

DIP3

Door station address

OFF

Only one door station, set to 000

OFF

Multi door station, first one address

OFF

Multi door station, second one address

OFF

Multi door station, third one address

OFF

Multi door station, fourth one address

OFF

Multi door station, fifth one address

OFF

Multi door station, sixth one address

ON ON ON Multi door station, seventh one address

4. DIPSwitches settings

Total 6 bits in the DIP switches can be configured. The switches can be modified either before or

after installation, but restart the power supply is needed whenever the switches have been

modified.

DIP1

DIP2

DIP3

The first three bit for door station ID settings

When multi-door stations are installed in the system, these three bit must be set

correctly, the door station’s DIP should set as below , If only one door station is

installed , set to 000.

The details as below:

DIP4

DIP4: button code selection

DIP4=OFF=chose default codes for each button: (0001~0104),

DIP4=ON=use the programmed codes, you can program each button on the

door station by ST CONFIG software

DIP5

DIP5: Unlocking time quick selection

DIP5=OFF=unlocking time 0.6 seconds

DIP5=ON=can program by PC through software ( by default 5 seconds)

DIP6

DIP6=OFF=normal mode

DIP6=ON=debug state enter, set to activate the debug state.

Debug mode:

When in this state, use the monitor to call , the outdoor station will call back

automatism

5. Place Name Plate

Press down and shift right/left to open the transparent nameplate cover, then insert the

name paper, then put the plate cover back to the panel. Note that double button line

panel can be opened both direction, single button line Can only be opened at right

side.

6. Standard Installation

7. Installation with expanding panel

8. ID CARD MANAGE

• Up to 1000 user cards can be registered by the Door Station.

• Easy management with LED state and Sound hint

.• There are two master cards, one MASTER CARD ADD card and one MASTER

CARD DELETE card, When adding a new master card, the old one will be replaced

automatically.

• Card reading distance is from 3 to 5 cm. The Master cards are necessary when you

add or delete user cards, Please keep the Master cards carefully.

However, it is much easier to manage the ID cards using ST-CONFIG software.

9. Other functions :

1. <PA,PB >function

operate

PB button

PA button

Trigger mode

activate the monitor refer to

the button at the right to

debug and check

Activate program the monitor

address, one time trigger one

Three seconds mode

activate the monitor refer to

the button at the left to debug

and check

Program “ master ADD card”

and “ master DELETE card”

Power on and push three

seconds Recover parameter by

default none

Power on and push three

seconds and short the

button which control open

the door

Recover parameter which is

default when it produce none

2. MONITOR FUNCTION:

need indoor monitor support this function

2.1. multi door station in one system, only the master door station can monitored by indoor

monitor

2.2. two indoor monitor can monitor(watch) in one time

2.3. monitor time: 30 seconds by default

3. INTERCOM FUNCTION

need indoor monitor support this function

4. MULTI OUTDOOR STATION

4.1. address should set to by DIP switch (details as above said) and the most quantity is

seven outdoor station can support ( include the master door station)

4.2. any of the door station can call the indoor monitor, but if one of the door stations is

contact with indoor monitor(audio phone), the other door station can not make a call,

there will be a sound of beep: BP+, BP+

5. DPA-MRMDS:

5.1. Single DPA-MRMDS connection (DPA-MRMDS address by default):

5.1.1. master door station connect to VD/IN;

5.1.2. the second door station connect to CAM-1;

5.1.3. the third door station connect to CAM-2;

5.1.4. the fourth door station connect to CAM-3;

5.2. in multi door station mode, when door station call indoor monitor, if the indoor

monitor have monitor function, then the DPA-MRMDS will output video from master

door station

6. SET TO INDOOR MONITOR’S ADDRESS

6.1.1. power the door station and connect the monitor to the door station correctly, in

the standby mode, press “PA” button( in the door station), there will be a hint

sound ”BP+,BP+”,, and the indicator light of button will be close, that means it

come to program mode;

6.1.2. then in five seconds , press the “call” button from indoor monitor, (otherwise, it

will quit the program in 60seconds) ,the outdoor station will a hint sound, then do

as below:

6.1.2.1. chose one wanted number button on the door station in two seconds, that

means the buttons you chose will be the indoor monitor’s room number.

Waiting for about 5 seconds, if there is a long “D--------“ sound from the

door station, that means the indoor monitor has been successfully

programmed. But if it sounds “BP, BP, BP” , that means the operation is

fail, should be the works again, if sounds “ BP, BP”, that means you use

the same button two times, make the room number repeat , so please chose

another button.

6.1.3. whatever success or fail for program, all the indicator light will be reback to light

6.1.4. if need program another indoor monitor, please work as above step by step once

again

Table of contents

Other XtendLan Intercom System manuals

XtendLan

XtendLan DPC-D246A User manual

XtendLan

XtendLan DPM-D271TMD User manual

XtendLan

XtendLan DPG-IP-G21 User manual

XtendLan

XtendLan DPC-W110-ID User manual

XtendLan

XtendLan DPC-434 Series User manual

XtendLan

XtendLan DPC-441 User manual

XtendLan

XtendLan DPM-535 User manual

XtendLan

XtendLan DPP-D203 User manual

XtendLan

XtendLan DPC-D268 User manual

XtendLan

XtendLan DPC-518ID User manual

XtendLan

XtendLan DT607 Series User manual

XtendLan

XtendLan DPC-D244-K User manual

XtendLan

XtendLan DPC-D248-R User manual

XtendLan

XtendLan DPM-D2101TMD User manual

XtendLan

XtendLan DPC-IP100 User manual

XtendLan

XtendLan DPC-IP101ID User manual

XtendLan

XtendLan DPM-451 User manual

XtendLan

XtendLan DPK-242 User manual

XtendLan

XtendLan DPC-D248-K User manual

XtendLan

XtendLan DPM-571 User manual

XtendLan

XtendLan DPC-536 Owner's manual

XtendLan

XtendLan DPC-D241-1 User manual

XtendLan

XtendLan DPC-D244-R User manual

XtendLan

XtendLan DPK-W100 User manual

Popular Intercom System manuals by other brands

Bticino

Bticino LINEA 3000 Installation

MSI

MSI MSI-140 owner's manual

golmar

golmar Stadio Plus instruction manual

CyberData

CyberData 011211 series Installation quick reference

Vidos

Vidos duo M1021 user manual

Vimar

Vimar ELVOX 7539/E Installation and operation manual

SSS Siedle

SSS Siedle BTSV 850-03 operating instructions

Dahua

Dahua VTO Series quick start guide

Elvox

Elvox 5651 Wiring instructions

Videx

Videx VIDEOKIT Series owner's manual

Rocom

Rocom Doortello Business FW T2.05W2.04 user guide

Viking

Viking E-35-EWP product manual

Safeguard Supply

Safeguard Supply LRA-EX1000 user manual

SSS Siedle

SSS Siedle BFCV 850 Series operating instructions

GRD

GRD MAX V2 user manual

Alecto

Alecto ADI-250 user manual

Aiphone

Aiphone IE-8MD Installation & operation manual

Perel

Perel EDB4 user manual