WorkPro MULTIPLAYER 4 User manual
v. 150601
User Manual / Instrucciones de Usuario
MULTIPLAYER 4
1. Read instructions - All the safety and operating instructions
should be read before the unit is operated.
2. Retain instructions - The safety and operating instructions
should be retained for future reference.
3. Heed warnings - all warnings on the unit and in the
operating instructions should be adhered to.
4. Follow instructions - All operations and other instructions
should be followed.
5. Water & Moisture - The unit should not be used near
water, for example, near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming
pool, etc.
6. Carts & Stands - The unit should be used only with a cart
or stand that is recommended by the manufacturer.
A unit and cart combination should be moved
with care.
Quick stops, excessive force, and uneven
surfaces may cause the unit and cart combination
to overturn.
7. Grounding or Polarization - Precautions should be taken
so that the grounding or polarization is not defeated.
8. Ventilation - The unit should not be situated so that its
location or position does not interfere with its proper
ventilation. For example, the unit should not be situated
on a bed, sofa, rug, or similar surface, that may block the
ventilation openings; or placed in a built-in installation,
such as a bookcase or cabinet that may impede the flow
of air through the ventilation openings.
9. Heat - The unit should be situated away from heat sources
such as radiators, stoves, or other appliances that produces
heat.
This symbol, wherever used,alerts you to
the presence of un-isulated and dangerous
voltages within the product enclosure.
These are voltages that may be sufficient to
constitute the risk of electric shock.
This symbol, wherever used, alerts you to
important operating and maintenance
instructions. Please read.
GRAPHICAL SYMBOLS EXPLANATION
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER
(OR BACK) NO USER SEVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED PERSONNEL.
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
TO RAIN OR HUMIDITY.DO NOT REMOVE COVER. THIS PRODUCT IS
NOT INTENDED FOR USE OTHER THAN STATED.
WARNING:
WARNING:
10. Power Sourcers - The unit should be connected to a
power supply only of the type described in the operating
instructions or as marked on the unit.
11. Power Cord Protection - Power supply cord should be
routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying
particular attention to cords at plugs, convenience
receptacles, and the point where they exit the unit.
12. Cleaning - The unit should be cleaned only as
recommended by the manufacturer.
13. Nonuse Periods - The power cord of the unit should be
unplugged from the outlet when left unused for a long
period of time.
14. Object and Liquid entry - Care should be taken so that
objects do not fall into and liquids are not spilled into the
inside of the unit.
15. Damage Requiring Service - The unit should be serviced
by qualified service personnel when:
A. The power supply cord or the plug has been damaged;
or
B. Objects have fallen, or liquid has been spilled into the
unit; or
C. The unit has been exposed to rain; or
D. The unit does not appear to operate normally or
exhibits a marked change in performance.
E. The unit has been dropped, or the cabinet damaged.
16. Servicing - The user should not attempt to service the
unit beyond those means described in the operating
instructiuons. All other servicing should be referred to
qualified personnel.
PAG. 1 User Manual/Manual de Instrucciones MULTIPLAYER 4
EN
Overview
Front Panel:
Rear panel:
ACCESSORIES:
AM Antenna Set x 1 FM Antenna Wire x1
RCA-RCA (L-R) Audio cable x1 AC Power cord x1
Remote Controller x 1
INSTALLATION:
1. Connect RCA-RCA cable to OUTPUT Terminal.
2. Connect AC Power Cord in between Socket and AC power resource in AC115/ 230V
Or connect DC Power Cord in DC13.2V Terminal.
according to local voltage. Remember to place the voltage selector in the proper position.
3. Connect RS232 Socket at rear.
4. Connect to Ground
PAG. 2 User Manual/Manual de Instrucciones MULTIPLAYER 4
EN
Anti Shock CD / USB - SD Card Reader / AM - FM Tuner
Features
- Provide CD , USB SD Card Reader and AM / FM Tuner function
- Compatible up to 16G USB, SD card / SDHC
- Accept 12 cm disc, such as CD, CD-R, CD-RW , MP3 disk
- Playing format: MP3, WMA
Button Instruction & CD / USB / SD READER Operation :
POWER : For switching the system on and off.
VOLUME : For adjusting the volume.
<<PLAY / II>> : Press to start and interrupt playing
MP3 Input / AUX Input : Connect MP3 input or other audio source
0 ~9 /M1 ~ M10 : 0~9 Numeral keys - Selecting the tracks
M1~M10 – Select the memory channel
<<STOP/ EJECT>> : to stops playing and ejec. t disk
Press to stop; LCD display shows all the number o ftracks.
Press again to eject the disk; LCD display shows “EJECT”
Press again, the disk will be automatically inserted.
<<CD / USB / SD / TUNER>>: Press the button to select the function of CD, USB, SD card or
TUNER mode.
RND: Play in a random order
Press to play all tracks in a random order. The LCD display shows “RANDOM”
Press again to cancel random play function.
Repeat : Repeat play
To play the ordinary format of music :
1. Press once to repeat current track. The LCD displays shows “REPEAT 1":
PAG. 3 User Manual/Manual de Instrucciones MULTIPLAYER 4
EN
2. Press again to repeat whole CD. The LCD display shows “REPEAT ALL”
3. Then press again to cancel repeat function
To play MP3 format of CD, USB, or SD Card :
1. Press to repeat current track. LCD display shows “Repeat”
2. Press again to repeat current folder. LCD display shows “REPEAT FOLDER”
3. Then press again to repeat whole tracks. LCD display shows “REPEAT ALL”
ALL”
4. Press again to cancel repeating function.
FOLDER : Forward to next folder.
FOLDER : Backward to last folder.
REV :
Press to backward to previous track.
Press for 5 seconds to fast backward the playing .
FWD :
Press to fast forward to next trac k.
Press for 5 seconds to fast forwarding the playin. g
<<MUTE>>: for temporarily muting the soun d.
<<PROG>> :To memorize the tracks are selected. Up to 10 tracks can be stored
Press <<PROG>>, LCD display shows “PROGRAM”. Seletc desired song by using
<<SKIP>> button, then press << ENTER>> button store 1st song, LCD display shows “00
01” for the 1st song. Press << ENTER>> again for storing 2nd song; LCD display shows “00
02”. Start over above process for storing up to 10 tracks.
Press PLAY / II to start play programmed tracks. Press REV or FWD button to
select programmed tracks.
Press PROG. Again to cancel program function.
TUNER OPERATION:
Press <<CD / USB / SD / TUNER>> button to select Tuner mode
BAND : Switching for FM or AM
TUN▲ / TUN ▼ : Press “▲” or ”▼” for searching station. Press for over 3 seconds enters
into automatic scan searching. Scanning stops when unit receiving station.
<<M1 ~ M10 >>buttons: memorizing radio stations.p U to 20 stations can be stored. AM x 10 /
FM x 10
Press TUN▲ / TUN ▼ button to start scan the station. Press <<M1~M10>> to store 1th
~ 10th stations button; LCD shows “CH1~10”.
To play the stored station, directly press <<M1~ M10>> button under TUNER mode.
PAG. 4 User Manual/Manual de Instrucciones MULTIPLAYER 4
EN
Note :
Please note that do not intend to insert the 8 cm disc or computer CD.
When inserts the disk into CD player or takes out the disk, it is required to let CD automatically
operation. It is prohibited to push or take out the disk by hand before the disk completely
in/out from device, otherwise it will damage the unit.
USB device
Insert USB in the faceplate.
Press CD / USB / SD / Tuner button on the remote controller front panel to select USB mode.
USB function will activate when “USB” appears on the LCD display.
PAG. 5 User Manual/Manual de Instrucciones MULTIPLAYER 4
EN
REMOTE CONTROL UNIT
CD / USB / SD READER OPERATION :
: Press to eject or insert the disk.
CD / USB / SD / TUNER : Press to select CD, USB, SD Card, or TUNER mode. The unit plays
automatically.
: PLAY / PAUSE. Press to play or pause.
:Stop to 。pla y
: Press to fast forward. Press again to cancel. Then press , back to normal play.
: Press once to activate fast reverse. Press again to cancel fast backward. Then
Press , back to normal play.
: Forward to next track.
: Backward to the previous track.
0 ~9 /M1 ~ M10 : 0~9 Numeral keys - Selecting thet racks
M1~M10 – Select the memory channel
:Repeat play function.
To play the ordinary format of music :
1. Press once to repeat current track. The LCD display shows “REPEAT 1".
2. Press again to repeat whole CD. The LCD display shows “REPEAT ALL”
3. Then press again to cancel.repeating function
To play MP3 format of CD, USB, or SD Card :
1. Press to repeat current track. LCD display shows “Repeat”
2. Press again to repeat current folder. LCD display shows “Repeat folder”
REP
PAG. 6 User Manual/Manual de Instrucciones MULTIPLAYER 4
EN
3. Then press again to repeat whole tracks. LCD display shows “Repeat all”
4. Press again to cancel repeating function.
: Press to play all tracks in a random order. LCD display
shows “ RANDOM “. Press again to cancel random play function.
: Press to forward to next folder, LCD display shows folder
Number
: ON / OFF Mute. For temporarily muting the sound
: Press to confirm the execution of operation.
Numeral 0 ~ 9 : Press to select desired track.
: To memorize the tracks are selected. Up to 10 tracks can be stored.
Press “PROG”, LCD display shows “PROGRAM” . Selec tdesired song by using SKIP
button, then press ENTER button to store 1st song, LCD display shows “00 01” for the 1st
song. Press ENTER again for storing 2nd song; LCD display shows “00 02”. Start over
above process for storing up to 10 tracks.
Press PLAY / II to start play programmed tracks. Press REV or FWD
button to select programmed tracks.
Press “PROG” again to cancel program function.
RADIO OPERATION :
CD / USB / SD / TUNER : press to select tuner mode.
BAND : Switching for FM or AM
AUTO SCAN - + : automatic scan searching. Scanning stops when unit receives station.
MEMORY : Up to 10 stations can be stored,
Press TUN ▲ / TUN ▼ button to start scan the station. Press M1~M10 buttons to store 1~10
stations.
M1 ~ M10 : Press to play memorized channels directly.
Remote controller shall appoint to the receiving ohle of faceplate. The optimal receiving
distance is 3 meters. The available distance is 5 meters.
Battery installation of the remote controlle r
RAN
FOLDER
PROG
TUN▲ / TUN ▼ : Press “▲” or ”▼” for searching station.
PAG. 7 User Manual/Manual de Instrucciones MULTIPLAYER 4
EN
PAG. 8 User Manual/Manual de Instrucciones MULTIPLAYER 4
Battery installation of the remote controller
1. To open up the battery cover (on the back side of the remote controller), Press down
the cap and slide it from the left to the right, then to pull it out.
2. Place a new battery (battery type: CR2025 3V, w/its positive upward).
3. Reverse the actions stated in the statement 1.
This symbol on the product or on its packaging indicates that this product
shall not be treated as household waste. Instead it shall be handed over to
the applicable collection point for the recycling of electrical an electronic
equipment. By ensuring this product is disposed of correctly, you will help
prevent potential negative consequences for the environment and human
health, which could otherwise be caused by inappropriate waste handling
of this product. The recycling of materials will help to conserve natural
resources. For more detailed information about recycling of this product,
please contact your local city office, your household waste disposal service
or the shop where you purchased the product.
This symbol on the product or on its packaging indicates that this product
shall not be treated as household waste. Instead it shall be handed over to
the applicable collection point for the recycling of electrical an electronic
equipment. By ensuring this product is disposed of correctly, you will help
prevent potential negative consequences for the environment and human
health, which could otherwise be caused by inappropriate waste handling
of this product. The recycling of materials will help to conserve natural
resources. For more detailed information about recycling of this product,
please contact your local city office, your household waste disposal service
or the shop where you purchased the product.
EN
RS232 - Command Code
The communication between computer and unit is
UART. The parameters are:
Start bit: 1 Parity bit :none
Data bits:8 Baud :9600
Stop bit:1 Command code format : HEX
PAG. 9 User Manual/Manual de Instrucciones MULTIPLAYER 4
EN
Function Button
EJECT 45 31 00 FF 46 0D 0A
PROG 45 31 00 FF 0D 0D 0A
RANDOM 45 31 00 FF 15 0D 0A
REPEAT 45 31 00 FF 08 0D 0A
PLAY/PAUSE 45 31 00 FF 4A 0D 0A
NEXT 45 31 00 FF 03 0D 0A
MUTE 45 31 00 FF 02 0D 0A
KEY3 45 31 00 FF 1F 0D 0A
KEY6 45 31 00 FF 11 0D 0A
KEY9 45 31 00 FF 59 0D 0A
STOP 45 31 00 FF 48 0D 0A
KEY2 45 31 00 FF 1D 0D 0A
KEY5 45 31 00 FF 1B 0D 0A
KEY8 45 31 00 FF 12 0D 0A
KEY0 45 31 00 FF 55 0D 0A
FWD. 45 31 00 FF 06 0D 0A
KEY1 45 31 00 FF 09 0D 0A
KEY4 45 31 00 FF 19 0D 0A
KEY7 45 31 00 FF 17 0D 0A
FOLDER 45 31 00 FF 50 0D 0A
REV 45 31 00 FF 5E 0D 0A
CD/USB/SD 45 31 00 FF 47 0D 0A
PREV 45 31 00 FF 05 0D 0A
BAND 45 31 00 FF 1E 0D 0A
TUNING Dn 45 31 FF 0E 0D 0A
TUNING Up 45 31 FF 1A 0D 0A
ENTER 45 31 FF 0F 0D 0A
AUTO Up 45 31 FF 45 0D 0A
AUTO Dn 45 31 FF 01 0D 0A
MEMORY 45 31 FF 52 0D 0A
Command Code
00
00
00
00
00
00
Table of contents
Languages:
Other WorkPro Media Player manuals
