Wirata LT-Q1 User manual
Model No.
LT-Q1
Output Power
0.32W
Power Supply
AC220V-240V
DC 3V (Battery UM-1x2)
Output Impedance
8 Ohm speaker
FM Radio Frequency Range
88 –108 MHz
MW Radio Frequency Range
530 - 1600 KHz
SW1-2 Radio Frequency Range
3-23 MHz
INSTRUCTION MANUAL
Model No.:
LT-Q1
Please read Instruction Manual before use
& Follow ALL the instructions carefully.
WHAT’S IN THE BOX
PARTS DESCRIPTION
1: Speaker 6: Band Button
2: Display scale 7: Aux-in jack
3: Battery door 8: Earphone jack
4: Tuning button 9: DC jack
5: Power switch/volume 10: AC jack
button
1. Radio –1set
2. Power cord –1pc
3. Instructional Manual –1pc
MAIN COMPONENT：
(Product may vary slightly from what is illustrated)
a) Power on/off, volume button operation:
i. Turn the (VOLUME) button clockwise, and it will turn
on when you hear a beep. Just adjust the volume to a
moderate position.
ii. Turn the (VOLUME) button counter clockwise, and it
will turn off when you hear a beep.
b) Switch radio FM position:
i. Push the function push button to the "FM" position, and
then turn the TUNING button (TUNING) to listen to any
radio program at 87.5-108MHz.
ii. Push the function push button to the "SW" position,
and then turn the tuning button (TUNING), you can
listen to any radio program from 3 to 23 MHz
iii. Push the function push button to the "AM" position,
and then turn the tuning button (TUNING), you can
listen to any radio program at 520-1710KHz.
c) Notice:
i. When listening to "FM/SW" broadcasts, please pull out
the telescopic antenna to get better reception results.
ii. AM When the receiving radio signal is not good, please
adjust the direction of the receiver to get a better
reception result.
d) External input audio (AUX-in) use:
i. Please insert the external audio input cable correctly
to the audio input port to amplify the external audio
source.
e) How to use the headphone:
i. When using the earphone, please plug the earphone
cable into the earphone jack. At this time, the inner
speaker will be disconnected automatically.
HOW TO OPERATE
1.USING THE POWER CORD/ BATTERY:
a) This machine can be used by plugging in the power cord
or installing dry batteries.
b) Remove the dry battery when using the power cord.
c) If there is a dry battery in the main unit, connect the
power plug to the socket and it will switch to household
power.
d) When using dry batteries, please unplug the power plug
from the socket.
2. WHEN USING HOUSEHOLD POWER
a) Plug the power cord into the AC socket of the main unit
to charge the built-in battery.
3. WHEN USING DRY BATTERIES
a) Press the battery door buckle, push and pull back, open
the battery door, insert 2 (UM-1 1.5V) batteries in the
correct direction as shown in the battery room and
close the battery door.
b) When installing the battery cover, please align the
holes first, and then press it down until you hear a
clicking sound.
Warning:
a) Pay attention to the (+/-) polarity direction of the dry
battery and insert the battery correctly according to
the instructions.
b) Remove the dry battery if you do not use it for a long
time or use the household power supply.
FUNTION INSTRUCTIONS
a) When you are not using this machine, please turn off the
power of this machine.
b) When playing, there will be noise/broken sound/lower
sound/distorted sound due to the following reasons:
i. The voltage may be too low. Charge the battery or
replace the battery in time.
ii. External signal interference, stop working.
c) There is no sound for the following reasons:
i. The power is not turned on or the switch is not turned
on.
ii. The speaker may be broken, please replace the
speaker.
d) If the machine is not used for a long time, the battery should
be taken out to prevent the battery fluid from leaking out
and damaging the machine.
ENVIRONMENT PROTECTION
Dispose the appliance according to the local
garbage regulations.
Never throw it away to the rubbish, so you will
help to the improvement of the environment.
TROUBLESHOOTING GUIDE
Table of contents
Other Wirata Radio manuals
