WESTERSTRAND AUREA II User manual

WESTERSTRAND URFABRIK AB Sweden

P.O. Box 133, SE-545 23 TÖREBODA Tel. +46 506-48000 Fax +46 506-48051

E-mail: info@westerstrand.se Internet: www.westerstrand.se

Instructions

AUREA II

Art. no. 119405-00, 119405-01, 119415-00, 119415-01

Trademarks

Westerstrand Urfabrik AB is a registered trademark.

All other trademarks or registered marks in this manual belong to their respective

manufacturers.

Disclaimer

Information in this document is subject to change without any notice and does not

represent a commitment on part of Westerstrand Urfabrik AB.

Westerstrand Urfabrik AB provides this document “as is,” without any warranty of any

kind, expressed or implied, including, but not limited to, its particular purpose.

Westerstrand Urfabrik AB reserves the right to make improvements and/or changes

to this manual, or to the products and/or the programs described in this manual, at

any time.

Information provided in this manual is intended to be accurate and reliable. However,

Westerstrand Urfabrik AB assumes no responsibility for its use, or for any

infringements on the rights of third parties that may result from its use.

This product might include unintentional technical or typographical errors. Changes

are periodically made to the information herein to correct such errors, and these

changes are incorporated into new editions of the publication.

Important Safeguards

Read all these instructions and save them for later use

Do not place this product on an unstable cart, stand or table. The product may

fall, causing serious damage to the product and/or person.

Slots and openings in the cabinet and the back are provided for ventilation to

ensure reliable operation of the product and to protect it from overheating,

these openings must not be blocked or covered. This product should never be

placed near or over a heat source. This product should not be placed in a

built-in installation unless proper ventilation is provided.

Never push objects of any kind into this product through cabinet slots as they

may touch dangerous voltage points or short out parts that could result in a

risk of fire or electric shock.

If installation is required, it must only be done by appropriately skilled

personnel.

Except as explained elsewhere in the operating manual, do not attempt to

service this product yourself. Removing covers may expose you to dangerous

voltage points or other risks. Refer all servicing in those compartments to a

service technician.

Product that intents to be connected to mains as a permanent installation shall

be connected by a readily accessible safety switch.

Is the product equipped with a plug (grounding type) shall this be connected to

an outlet that is intended for the product. The plug must be easy to disconnect

without moving or dismantle the product.

CAUTION: this equipment must be serviced by an approved technician.

The guarantee shall be cancelled if any modifications are made to this product.

General warning (refer to accompanying documents)

Consult instruction for use

This symbol means that according to local laws and regulations your

product shall be disposed of separately from household waste. When this

product reaches its end of life, take it to a recycling center designated by

local authorities.

Document: 1463en08.doc

Author: CAn

Date:

2000-06-22

Page: 1 of 10

WESTERSTRAND URFABRIK AB

P.O. Box 133 Tel. +46 506 48000 Internet:: www.westerstrand.se

SE-545 23 TÖREBODA Fax. +46 506 48 051 E-mail: info@westerstrand.se

GENERAL....................................................................................................... 2

Options ....................................................................................................... 2

INSTALLATION............................................................................................... 3

SETTINGS OF DIP-SWITCHES .......................................................................... 5

....................................................................................................................... 6

MOUNTING .................................................................................................... 6

MANUAL PROGRAMMING.............................................................................. 7

Time............................................................................................................ 7

Date............................................................................................................. 8

Spec ............................................................................................................ 8

DCF (Radio synchronising DCF/RDS/MSF)............................................ 9

WHAT HAPPENS IF POWER IS DOWN? ............................................................ 9

TECHNICAL SPECIFICATION......................................................................... 10

Instructions

AUREA II

Art. no. 119405-00, 119405-01, 119415-00, 119415-01

Document: 1463en08.doc

Author: CAn

Date:

2000-06-22

Page: 2 of 10

WESTERSTRAND URFABRIK AB

P.O. Box 133 Tel. +46 506 48000 Internet:: www.westerstrand.se

SE-545 23 TÖREBODA Fax. +46 506 48 051 E-mail: info@westerstrand.se

General

Aurea II is a digital clock for indoor use. The clock can be operated as a stand-alone unit, via

impulse from a master clock or radio signal (option). The clock has a built in calendar and the

ability to perform automatic daylight saving correction. The light intensity of the display can be

changed. There is also an automatic “night dimmer” which adjust the light intensity of the

display when the light that surrounds the clock decreases below a certain level. This function can

be turned off if wanted.

Important !

The clock has a lithium backup battery used as backup power when the main power is off. This

battery has a limitation of 1000 active working hours. The backup battery can be turned off by

disconnecting the jumper “BAT”. (See fig. Clock backside). At delivery the “BAT” jumper is

left open (not connected). To enable the backup battery the “BAT” jumper must be connected

(closed). If the clock is not to be used for some time disconnect the “BAT” jumper before

storage.

Options

For connections of options see separate instructions. Following options are available;

•Radio receiver DCF, MSF, RDS

•IRIG-B –input

•LTC (SMPTE/EBU) –input (factory mounted option)

•LON-input (factory mounted option)

•Time code via RS485-input (factory mounted option)

Document: 1463en08.doc

Author: CAn

Date:

2000-06-22

Page: 3 of 10

WESTERSTRAND URFABRIK AB

P.O. Box 133 Tel. +46 506 48000 Internet:: www.westerstrand.se

SE-545 23 TÖREBODA Fax. +46 506 48 051 E-mail: info@westerstrand.se

Installation

The clock consists of two parts, a back plate and the actual clock. The back plate is a connection

plate to which all connection shall be made.

Fig. Back plate

The two holes “A” (Fig. Back plate) with a relative distance of 160 mm are used for mounting

the back plate to a wall. The back plate can also be mounted to a wall by the two holes “B” (Fig.

Back plate),with 60 mm distance and can be fitted directly to a coupling-box, given it has the

same dimensions.

The Locking screw (Fig. Back plate) is for locking of the clock to the back plate (see mounting

description below for further details).

The power (230 AC 50Hz) shall be connected to the power terminal at the back plate (Fig. Back

plate). A switch or a circuit breaker, disconnecting all current carrying conductors, shall be

included in the wiring installation.

Installation fuse: 10A max

Supply cable: 1,5 mm2

Document: 1463en08.doc

Author: CAn

Date:

2000-06-22

Page: 4 of 10

WESTERSTRAND URFABRIK AB

P.O. Box 133 Tel. +46 506 48000 Internet:: www.westerstrand.se

SE-545 23 TÖREBODA Fax. +46 506 48 051 E-mail: info@westerstrand.se

The different types of external time synchronisation sources shall be connected to the Sync

terminal (Fig. Back plate) according to:

1/2 minute and 1/1 minute impulse (sync or slave)

Signal source Sync terminal (Fig. back plate)

IMP+ 4

IMP- 3

In this configuration the 3-wire jumper (Fig. Clock backside) must be left open (not connected).

Radio signal, 2-wire connection

Synchronisation terminal Signal source

in Aurea II

In this configuration the 3-wire jumper (Fig. Clock backside) must be open (not installed).

Radio signal, 3-wire connection

Synchronisation terminal Signal source

in Aurea II

Connect 2 and 4.

In this configuration the 3-wire jumper (Fig. Clock backside) must be closed (connected).

DCF

Document: 1463en08.doc

Author: CAn

Date:

2000-06-22

Page: 5 of 10

WESTERSTRAND URFABRIK AB

P.O. Box 133 Tel. +46 506 48000 Internet:: www.westerstrand.se

SE-545 23 TÖREBODA Fax. +46 506 48 051 E-mail: info@westerstrand.se

Settings of dip-switches

Before mounting the clock to the back plate, operating mode must be selected via 5 dip-switches

at the backside of the clock (Fig. Clock backside). Dip 3, 4 and 5 selects which clock

synchronisation to use. Dip 1 and 2 selects which daylight saving rules to use (if any).

At the backside of the clock there are 5 dip-switches to configure the clock:

Dip 3 4 5

Off Off Off Stand-alone clock.

Off On Off Radio synchronisation (DCF, MSF, RDS)/ IRIG-B, LON, LTC.

Off Off On Impulse clock 1/2 minute (sync).

Off On On Impulse clock 1/1 minute (sync).

On Off On Impulse clock 1/2 minute (slave).

On On On Impulse clock 1/1 minute (slave).

Dip 1 2

Off Off No automatic daylight saving correction.

Off On Finnish daylight saving rules (First Sunday between 25-31 march at 3:00 and

first Sunday between 25-31 October at 4:00).

On Off Middle Europe daylight saving rules (First Sunday between 25-31 march at

2:00 and first Sunday between 25-31 October at 3:00).

On On England daylight saving rules (First Sunday between 25-31 march at 1:00 and

first Sunday between 25-31 October at 2:00).

Note: When the clock is configured as a 1/1 minute impulse slave or a 1/2 minute impulse

slave, dip 1 and 2 must be Off (No automatic daylight saving correction).

Document: 1463en08.doc

Author: CAn

Date:

2000-06-22

Page: 6 of 10

WESTERSTRAND URFABRIK AB

P.O. Box 133 Tel. +46 506 48000 Internet:: www.westerstrand.se

SE-545 23 TÖREBODA Fax. +46 506 48 051 E-mail: info@westerstrand.se

Fig. Clock backside

Mounting

After all connections has been made and the back plate has been mounted to a wall, mount the

clock to the back plate according to:

-First unlock the locking screw (Fig. Back plate)

-Mount the clock to the back plate according to Fig. Mounting

-Lock the locking screw (Fig. Back plate)

Don’t forget to connect the “BAT” jumper (Fig. Clock backside) before mounting the clock to

the backplate.

This manual suits for next models

Table of contents

Other WESTERSTRAND Clock manuals

WESTERSTRAND

WESTERSTRAND Analogue NTP Clock User manual

WESTERSTRAND

WESTERSTRAND QUARTZ MOVEMENT User manual

WESTERSTRAND

WESTERSTRAND Lumex 5 User manual

WESTERSTRAND

WESTERSTRAND Analogue NTP Clock User manual

WESTERSTRAND

WESTERSTRAND QUARTZ CLOCK User manual

WESTERSTRAND

WESTERSTRAND Quartz Movement User manual

WESTERSTRAND

WESTERSTRAND QWTIME III WDP M+S User manual

WESTERSTRAND

WESTERSTRAND Analogue clock User manual

WESTERSTRAND

WESTERSTRAND KNX User manual

WESTERSTRAND

WESTERSTRAND CIRCLE LINE User manual

WESTERSTRAND

WESTERSTRAND Wireless Clock User manual

WESTERSTRAND

WESTERSTRAND mini WDP-Y User manual

WESTERSTRAND

WESTERSTRAND CIRCLE LINE NTP PoE User manual

WESTERSTRAND

WESTERSTRAND CIRCLE LINE User manual

WESTERSTRAND

WESTERSTRAND Lumex 5 User manual

WESTERSTRAND

WESTERSTRAND LUMEX 7 User manual

WESTERSTRAND

WESTERSTRAND Analog indoor clock with WiFi User manual

WESTERSTRAND

WESTERSTRAND QWTIME III WDP-WL User manual

WESTERSTRAND

WESTERSTRAND Lumex 5 User manual

WESTERSTRAND

WESTERSTRAND Analogue NTP Clock User manual

WESTERSTRAND

WESTERSTRAND CIRCLE LINE NTP User manual

WESTERSTRAND

WESTERSTRAND AUREA ALPHA User manual

Popular Clock manuals by other brands

Silicon Laboratories

Silicon Laboratories SI5324 manual

Heathkit

Heathkit GC-1005 Assembly manual

Oregon Scientific

Oregon Scientific PRYSMA RMR221P manual

Andrew O'Malley

Andrew O'Malley DOTKLOK Assembly instructions

ALGE-Timing

ALGE-Timing ASC3 manual

Bodet

Bodet Profil 960 Installation and operating instructions

Nixie Clock

Nixie Clock Divergence Meter user manual

La Crosse Technology

La Crosse Technology WS-8256-AL user manual

Mini Gadgets

Mini Gadgets MCPro user manual

Casio

Casio TMR-200 user guide

Progetti

Progetti ILTEMPOSTRINGE Directions

BVItech

BVItech BV-101 instruction manual

Progetti

Progetti KALIMERO Directions

La Crosse Technology

La Crosse Technology WT-3141b Quick setup instructions

La Crosse Technology

La Crosse Technology W86531 owner's manual

Sharp

Sharp SPC900 instruction manual

La Crosse Technology

La Crosse Technology 404-50447 quick start guide

Datexx

Datexx DF0063 quick guide