WeBoost DRIVE X FLEET User manual

PROFESSIONAL VEHICLE CELL

SIGNAL BOOSTER KIT

DRIVE X FLEET

A WILSON ELECTRONICS BRAND

NEED HELP? support.weboost.com

Use our weBoost App to guide you through the installation.

See inside page for more details.

1-866-294-1660

Installation Guide

Download the weBoost App

Use our app to guide you through setting up a weBoost cell phone

signal booster in your home, business, or vehicle. Boost every

network, including 5G, right away.

Download the weBoost App

Videos to guide you

through installation

Antenna positioning guide

for optimal performance

Before and after cell

signal readings

______

Index

Package Contents 1

STEP 1: Drill Cable Entry Hole To Your Vehicle 2

STEP 2: Mount NMO Outside Antenna 5

STEP 3: Mount In-Vehicle Antenna 6

STEP 4: Wire The Power Supply 7

STEP 5: Connect Coax Cables To Booster 8

STEP 6: Connect Power Supply To Booster 9

Light Patterns 10

Troubleshooting 11

Safety Guidelines 13

Speciﬁcations 14

Warranty 15

1PROFESSIONAL VEHICLE SIGNAL BOOSTER KIT DRIVE X FLEET

________

Package

Contents

Drive X

Booster

& Bracket

Outside NMO

Antenna +

Connector

Mounting Cable

In-Vehicle

Antenna Power

Supply

Optional Antenna

Extension Cable Protective Tape

For Installation O-Ring Lubricant

Packet

DRIVE X FLEET PROFESSIONAL VEHICLE SIGNAL BOOSTER KIT 2

______

Step 1: Drill Cable Entry Hole

To Your Vehicle

Identify a location for NMO outside antenna on the

top of your vehicle that is:

 Near the center of the roof

 At least 12 inches away from any other antennas

 At least 12 inches away from any windows

(for best performance install on top of vehicle)

Do a ‘soft install’ before drilling the hole for the

cable entry.

Set up the system by routing the cable through

an open door or window, completing the setup

instructions, verifying the system works as desired,

and then drilling the hole.

12 in. away from windows

(including sunroofs)

Good NMO Outside

Antenna Placement

3PROFESSIONAL VEHICLE SIGNAL BOOSTER KIT DRIVE X FLEET

Place the protective tape on the

vehicle in the desired location.

Using a 3/4” hole saw, drill a

hole in the center of the

protective tape.

______

(STEP 1 cont.)

After completing the ‘soft install’ and identifying NMO

outside antenna location:

protective tape

vehicle surface

protective tape

3/4” bit

DRIVE X FLEET PROFESSIONAL VEHICLE SIGNAL BOOSTER KIT 4

apply silicone grease

After hole has been drilled, insert NMO Mounting Cable

through (SMA connector end ﬁrst) and remove collar.

Position threads of the cable mount above vehicle surface.

Apply included silicone grease to the o-ring on the collar

then screw the collar to the base mount. Ensure the mount is

centered in the hole and tighten with wrench.

screw collar

to base mount

For a professional installation, we recommend routing the cable

under the headliner and down through the side trim panel to

the desired booster location on the ﬂoor of the vehicle.

side trim panel

headliner

remove

collar

insert through hole

______

(STEP 1 cont.)

5PROFESSIONAL VEHICLE SIGNAL BOOSTER KIT DRIVE X FLEET

Before attaching the antenna, apply a thin layer of silicone

grease to the threads, only, to the NMO mount and to the

o-ring on the antenna. Screw the antenna onto the NMO

mount and hand tighten into place.

hand tighten and make sure

gasket is touching vehicle

surface

screw on

NMO Antenna

______

Step 2: Mount NMO

Outside Antenna

apply silicone grease

NOTE: DO NOT apply silicone grease to the antenna pin contact surface.

DRIVE X FLEET PROFESSIONAL VEHICLE SIGNAL BOOSTER KIT 6

The location should be at least 18 inches but no more than

36 inches from where the cell phone device will be used.

Adhesive and Velcro® mounting options are included.

In-Vehicle Antenna

Identify a place to mount the in-vehicle antenna, either on

the side of the seat or on the dash and mount.

______

Step 3: Mount In-Vehicle

Antenna

clean surface of dash before attaching

adhesive strip

dash option

seat option

In-Vehicle

Antenna

7PROFESSIONAL VEHICLE SIGNAL BOOSTER KIT DRIVE X FLEET

Before connecting the power supply, disconnect the vehicle battery

leads to avoid any electrical shocks during installation.

Locate a place where cables are already running through the ﬁrewall

(rear wall of engine bay) to the inside of the cabin.

Locate the same ﬁrewall hole from inside of the vehicle cabin.

Route the power cables of the power supply from the inside of the

vehicle cabin out through ﬁrewall hole.

Note: The cables must be routed inside to outside since the power

supply brick won’t ﬁt through the ﬁrewall holes. The power supply

brick should remain inside the vehicle cabin.

Connect the positive lead of the power supply (lead with red tape)

to the disconnected positive (+) lead of the battery (not the positive

terminal on the battery itself).

Connect the negative lead of the power supply (lead without tape)

to the disconnected negative (-) lead of the battery (not the negative

terminal on the battery itself).

Connect the positive (+) lead back to the vehicle battery.

Connect the negative (-) lead back to the vehicle battery.

Use steps below as a draft/template of the general install of

the power supply.

______

Step 4: Wire The Power

Supply

NOTE: Having the power supply directly connected to the battery may

drain the battery’s life. Please review the vehicle’s owner’s manual for more

information. Adding a “fuse tap” may be another solution. A “fuse tap” is an

electrical part that functions as a power splitter and is meant to be installed

in the car’s fuse box, making the amp shut o when the vehicle’s ignition

switch is turned o.

Table of contents

Other weBoost Extender manuals

weBoost

weBoost Drive 3G-Flex 470013 User manual

weBoost

weBoost Basic Home User manual

weBoost

weBoost Connect 4G 470003 User manual

weBoost

weBoost SIGNAL 3G User manual

weBoost

weBoost Drive Reach Fleet User manual

weBoost

weBoost 472061 User manual

weBoost

weBoost DRIVE 3G-S User manual

weBoost

weBoost DRIVE 4G-X OTR User manual

weBoost

weBoost DRIVE SLEEK User manual

weBoost

weBoost DRIVE 3G-S User manual

weBoost

weBoost Drive AM100-Pro User manual

weBoost

weBoost 460059 User manual

weBoost

weBoost Drive 3G-M+ User manual

weBoost

weBoost DRIVE 4G-X FLEET User manual

weBoost

weBoost Drive 3G-X SmarTech III 470011 User manual

weBoost

weBoost DRIVE SLEEK U470035 User manual

weBoost

weBoost DRIVE REACH OTR FLEET User manual

weBoost

weBoost Home Room User manual

weBoost

weBoost Home-4G 470001 User manual

weBoost

weBoost Drive Reach OTR User manual

weBoost

weBoost Home Complete 460045 User manual

weBoost

weBoost Home Complete 460045 User manual

weBoost

weBoost DRIVE 4G-X FLEET User manual

weBoost

weBoost 470113 User manual

Popular Extender manuals by other brands

SY HDBT-60T installation guide

Appsys ProAudio

Appsys ProAudio ADX-16 user manual

Atlona

Atlona RS232 user manual

IDK

IDK OPF-TH1000-A user guide

Enable-IT

Enable-IT 824WP quick start guide

Worx

Worx Landroid RadioLink WA0864 Get started

TP-Link

TP-Link TL-WA730RE user guide

Camplex

Camplex CMX-HDMI-SFPL user manual

SC&T

SC&T HE03-4K user manual

Marmitek

Marmitek MegaView70 user manual

Samsung

Samsung SCS-26UC4 user guide

Foxun

Foxun SX-GES24 operating instructions

MuxLab

MuxLab 500771 Operation manual

foxunhd

foxunhd SX-AEX01 operating instructions

TERK Technologies

TERK Technologies LFIRX2 owner's manual

Devolo

Devolo Audio Extender supplementary guide

Edimax

Edimax EW-7438RPn V2 instructions

Shinybow USA

Shinybow USA SB-6335T5 instruction manual

weBoost DRIVE X FLEET User manual

Popular Extender manuals by other brands