weBoost Drive Reach Fleet User manual
______
Index
Package Contents
1
STEP 1-A: Drill Cable Entry Hole Into Your Vehicle
2
STEP 1-B: Insert & Route Cable
4
STEP 1-C: Mount NMO Outside Antenna
5
STEP 2: Mount 4G In-Vehicle Antenna
6
STEP 3: Wiring The Power Supply To The Vehicle Battery
7
STEP 4: Connect Coax Cables To Booster
8
STEP 5: Connect Power Supply To Booster
9
Light Patterns
10
Troubleshooting
11
Safety Guidelines
12
Specifications
13
Warranty
Back Cover
DRIVE REACH FLEET PROFESSIONAL VEHICLE SIGNAL BOOSTER KIT 1
________
Package
Contents
Drive Reach
Booster
& Bracket
Outside NMO
Antenna +
Connector
Mounting Cable
4G In-Vehicle
Antenna
Power
Supply
Optional Antenna
Extension Cable
Protective Tape
For Installation
O-Ring Lubricant
Packet
2PROFESSIONAL VEHICLE SIGNAL BOOSTER KIT DRIVE REACH FLEET
______
Step 1-A: Drill Cable Entry
Hole Into Your Vehicle
Identify a location for NMO Outside Antenna on the
top of your vehicle that is:
Near the center of the roof
At least 12 inches away from any other antennas
At least 6 inches away from any windows
(for best performance install on top of vehicle)
Do a ‘soft install’ before drilling the hole for the
cable entry.
Set up the system by routing the cable through
an open door or window, completing the setup
instructions, verifying the system works as desired,
and then drilling the hole.
6 in. away from windows
(including sunroofs)
Good NMO Outside
Antenna Placement
DRIVE REACH FLEET PROFESSIONAL VEHICLE SIGNAL BOOSTER KIT 3
Place the protective tape on the
vehicle in the desired location.
Using a 3/4” hole saw, drill a
hole in the center of the
protective tape.
______
(STEP 1-A cont.)
After completing the ‘soft install’ and identifying NMO
Outside Antenna location:
protective tape
vehicle surface
protective tape
3/4” bit
4PROFESSIONAL VEHICLE SIGNAL BOOSTER KIT DRIVE REACH FLEET
apply silicone grease
After hole has been drilled, insert NMO Mounting Cable
through (connector end first) and remove collar.
Position threads of the cable mount above vehicle surface.
Apply included silicone grease to the o-ring on the collar
then screw the collar to the base mount. Ensure the mount is
centered in the hole and tighten with wrench.
screw collar
to base mount
For a professional installation, we recommend routing the cable
under the headliner and down through the side trim panel to
the desired booster location on the floor of the vehicle.
side trim panel
headliner
r
u
n
c
a
b
l
e
f
r
o
m
N
M
O
O
u
t
s
i
d
e
A
n
t
e
n
n
a
t
o
b
o
o
s
t
e
r
______
Step 1-B: Insert & Route Cable
remove
collar
insert through hole
DRIVE REACH FLEET PROFESSIONAL VEHICLE SIGNAL BOOSTER KIT 5
Before attaching the antenna, apply a thin layer of silicone
grease only onto the threads of the NMO mount and onto
the o-ring on the antenna. Screw the antenna onto the NMO
mount and hand tighten into place.
hand tighten and make sure
gasket is touching vehicle
surface
screw on
NMO Antenna
______
Step 1-C: Mount NMO
Outside Antenna
apply silicone grease
NOTE: DO NOT apply silicone grease to the antenna pin contact surface.
6PROFESSIONAL VEHICLE SIGNAL BOOSTER KIT DRIVE REACH FLEET
The location should be at least 18 inches but no more than 36
inches from where the cellular device will be used. Use the
Velcro® adhesive strip or the 2-sided adhesive strip provided
and attach to the side of the antenna labeled “MOUNTING
SIDE”. Then mount to the desired location.
Identify a place to mount the 4G In-Vehicle Antenna, either
on the side of the seat or on the dash and mount.
______
Step 2: Mount 4G In-Vehicle
Antenna
In-Vehicle Antenna
Dash Mount
Velcro® strip
In-Vehicle Antenna
Seat Mount
DRIVE REACH FLEET PROFESSIONAL VEHICLE SIGNAL BOOSTER KIT 7
Before connecting the power supply, disconnect the vehicle battery
leads to avoid any electrical shocks during installation.
Locate a place where cables are already running through the firewall
(rear wall of engine bay) to the inside of the cabin.
Locate the same firewall hole from inside of the vehicle cabin.
Route the power cables of the power supply from the inside of the
vehicle cabin out through firewall hole.
Note: The cables must be routed inside to outside since the power
supply brick won’t fit through the firewall holes. The power supply
brick should remain inside the vehicle cabin.
Connect the positive lead of the power supply (lead with red tape)
to the disconnected positive (+) lead of the battery (not the positive
terminal on the battery itself).
Connect the negative lead of the power supply (lead without tape)
to the disconnected negative (-) lead of the battery (not the negative
terminal on the battery itself).
Connect the positive (+) lead back to the vehicle battery.
Connect the negative (-) lead back to the vehicle battery.
Use steps below as a draft/template of the general install of
the power supply.
______
Step 3: Wiring The Power
Supply To The Vehicle Battery
1
2
3
4
5
6
7
8
NOTE: Having the power supply directly connected to the battery may
drain the battery’s life. Please review the vehicle’s owner’s manual for more
information. Adding a “fuse tap” may be another solution. A “fuse tap” is an
electrical part that functions as a power splitter and is meant to be installed
in the car’s fuse box, making the amp shut o when the vehicle’s ignition
switch is turned o.
8PROFESSIONAL VEHICLE SIGNAL BOOSTER KIT DRIVE REACH FLEET
______
Step 4: Connect Coax Cables
To Booster
Connect the cable from the Outside NMO Antenna to the port
labeled “Outside Antenna” on the booster.
Connect the cable from the 4G In-Vehicle Antenna to the port
labeled “Inside Antenna” on the booster.
from Outside NMO Antenna
from Inside Antenna
NOTE: Bracket can be used to fasten booster in a specific location if desired.
The Velcro® strip on the bottom of the bracket can also be used to keep
booster from sliding around.
bracket
Drive Reach
Table of contents
Other weBoost Extender manuals
weBoost
weBoost DRIVE X OTR FLEET User manual
weBoost
weBoost Office 200 User manual
weBoost
weBoost DRIVE REACH OTR FLEET User manual
weBoost
weBoost 460066 User manual
weBoost
weBoost Home MultiRoom 530044 User manual
weBoost
weBoost SIGNAL 3G User manual
weBoost
weBoost Home Room 460020 User manual
weBoost
weBoost DRIVE X RV User manual
weBoost
weBoost 473105 User manual
weBoost
weBoost Destination RV User manual
weBoost
weBoost DRIVE 3G-S User manual
weBoost
weBoost DRIVE 4G-X OTR User manual
weBoost
weBoost DRIVE 4G-X FLEET User manual
weBoost
weBoost DRIVE 4G-X OTR 470210R User manual
weBoost
weBoost Drive AS100 User manual
weBoost
weBoost Drive AM100-Pro User manual
weBoost
weBoost 460059 User manual
weBoost
weBoost Home MultiRoom 650144 User manual
weBoost
weBoost Home 4G User manual
weBoost
weBoost Home Room U530001 User manual
