Wayhom W934D User manual
SOLAR POWERED FLOOD LIGHT
W934D
8 x Wall plugs
8 x Mounting Screws
2 x Rechargeable Batteries
-
+
+-
Please read these instructions thoroughly prior to installation, then store in a safe place for future reference.
1 x Solar Panel
1 x Motion Light
1
2
CARE & MAINTENANCE
• From time to time, ensure the plug between the solar panel and light is securely connected.
• It is advisable to adjust the angle of the solar panel to optimize the exposure of the sun during the
winter months.
• The solar panel should be cleaned with a damp cotton cloth on a regular basis. This will ensure optimal
performance and battery charging. Periodically, utilize the same technique to clean the lenses of the
motion lights.
• Never let any abrasive material come into contact with the solar panel.
INSTALLATION
Ensure your solar panel is placed where exposes
to optimized sunlight. Be aware of objects such
as trees or property overhangs that may impede the
panel’s ability to generate a charge.
Optional: Use a power drill (not included) to create
the holes on your chosen mounting surface.
Use 4 of the included wall plugs and screws to
fasten the solar panel to the surface.
Buckle the motion light into the mounting plate
securely.
Use a power drill (not included) to drill the
holes on your chosen mounting surface.
Place the mounting plate over the holes &
use 4 of the included wall plugs and screws to
fasten the mounting plate to the surface.
• Your motion light is not a toy. Keep it out of reach from small children.
• Your motion light and solar panel are both weather-resistant.
• You can mount your motion light indoors, but your solar panel must be installed outdoors to receive light
from the sun.
• If using a step ladder, you may require a second person to help install the solar motion light.
• Prior to installation, lay out all components and check against the part list section in this manual.
• Never look directly into the solar motion light when illuminated.
SAFETY INFORMATION
When replacing the batteries, be sure to:
• Use rechargeable batteries only.
• Observe the correct polarity (+ and -) when installing the replacement batteries.
• Do not mix old and new batteries and Do not mix alkaline, standard(carbon-zinc)
or rechargeable (ni-cad, ni-mh, etc.) batteries.
• IMPORTANT: Dispose of the Lithium ion battery in accordance with local, state and federal regulations.
BATTERY REPLACEMENT INSTRUCTIONS
WARRANTY
PRODUCT FEATURES
This product is covered under a one year limited warranty. Manufacture warrants to the original
purchaser that this product is free from defects in materials and workmanship for the period of one year from
date of purchase. The included batteries are not covered under this warranty.
Proof of purchase including date, and explanation of complaint is required for warranty service.
• 64 LEDs
• Adjustable motion sensor
• Adjustable time and sensitivity settings
• Solar panel with 15 ft wire
1
2
4
3
NOTE: Recommended Tools:
Power Drill,
Phillips Screwdriver
3
57
8
6
4
Batteries are located in the battery housing behind the light
the battery housing. Remove the four screws to reveal the
batteries.
When replacing the batteries, observe the correct polarity
have removed. Use rechargeable batteries only.
Two different control switches adjust the light’s illumination time
and range of motion detection.
TIME: Determines the duration of the light once motion is detected:
30 seconds, 60 seconds or 120 seconds.
TEST:
SENSITIVITY: Controls the distance of the range of motion
detection: low, medium or high.
8
57
6
Connect the wire from the solar panel into the socket
now begin to charge.
ON | OFF | AUTO ON |OFF | AUTO ON | OFF | AUTO
Before using the solar security light,the solar panel needs to be
connected to the light for THREE DAYS.The initial charge should
be done in the OFF(O) position.
After this, there will be enough power of batteries to operate the
light. Place the light in the AUTO(I) mode.
Push the switch to “ON”(II) to turn on the normally on mode.This
will allow a limited period of constant illumination.
Allows the positioning of the light’s motion sensor to be
tested day or night. Once the motion sensor is in the desired
position, attempt to trigger the light by moving in the
intended detection zone. If the light illuminates, the motion
sensor is positioned correctly. You are now ready to move
the switch to the preferred duration option. The light will now
only turn on in darkness.
CUSTOMER SERVICE
2-Year limited warranty Lifetime techinical support
Wayhom is a trademark of LEDMAN ELECTRONIC TECHNOLOGY (HK) CO., LIMITED.
Tung Lee Building, KL, Hong Kong.
All rights reserved.
5
FREQUENTLY ASKED QUESTIONS
Q: Where should the solar panel be mounted?
A: Mount your solar panel in a position that will enable the most amount of light to be absorbed (refer to Step 1 on page 2). In the Northern
Hemisphere this is usually south facing.
Q: Does the solar panel require direct sun to charge?
A: The solar panel can charge the internal batteries in direct and indirect light. For best results, try to optimize your solar panel’s sun exposure.
Q: Can additional or extended cable wire for the solar panel be purchased?
A: At this point there are no extensions available for the cable that connects the light to the solar panel. Any additions to the cable will void
the warranty.
Q: Will decorative or street lights have an effect on the motion sensors’s ablity to operate?
A: Yes, the sensor of the solar motion light is light-sensitive. For nighttime usage, ensure no other light activates the motion sensor.
Q: What type of battery does my solar motion light require to operate?
A: Your solar motion light requires the use of 2 pcs of 3.7V 18650 1800MAH Lithium ion rechargeable batteries.
A:
sunny days to bring the batteries to full charge. After three days, return the switch to the“AUTO" position.
three
Table of contents
Other Wayhom Floodlight manuals
