Waterco Admiral Guide

This equipment must be installed and serviced by a qualified technician. Improper installation may result in
property damage, serious injury or death. Improper installation and/or operation will void the warranty.
Notice to Installer
This manual contains important information about the installation, operation & safe use of this product.
Once the product has been sold or installed this manual must be given to the owner/operator of this equipment.
ROBOTIC POOL CLEANER
Installation - Operation - Warranty Manual
www.waterco.com
WARNING

Table of Contents
Safety Information 2-3
General Instructions 3
Installation 4
RCD Operation 4
Removing Cleaner from Pool 5
Cleaning Filter Bags 5-6
Power Cord Maintenance 6-7
CONGRATULATIONS
Congratulations and thank you for choosing our Admiral Pool Cleaner the most technologically advanced automatic
Robotic Pool Cleaner available.
We are sure you will find your new Admiral a pleasure to use. Before you use the cleaner, we recommend that you read through the relevant
sections of this manual, which provides a description of your cleaner and its functions.
To avoid the risks that are always present when you use a Robotic Pool Cleaner, it is important that the cleaner is installed correctly and that
you read the safety instructions carefully to avoid misuse and hazards.
We recommend that you keep this instruction booklet for future reference and pass it on to any future owners.
After unpacking the Admiral, please check it is not damaged. If in doubt, do not use the cleaner but contact the store where you purchased
the cleaner.
WARNING
1. DO NOT RUN THE ADMIRAL OUT OF THE WATER. OPERATING THE CLEANER OUT OF THE WATER WILL DAMAGE THE MOTORS AND
VOID THE WARRANTY
2. THE ADMIRAL SHOULD NOT BE CONNECTED TO A TIMING DEVICE AND LEFT CONTINUOUSLY WITHIN A POOL OR SPA.
3. DON’T USE EXTENSION CORDS OR ADAPTER PLUGS WITH THE ADMIRAL – AS THIS MAY AFFECT THE CLEANER’S PERFORMANCE AND
EXPOSURE TO ELECTROCUTION (EXPOSURE TO PERSONAL INJURY OR DEATH).
SAFETY INFORMATION
1. Waterco’s Admiral Robotic Pool Cleaner is designed to work with water at a temperature greater than 13ºC (55ºF) and less than 45ºC (113ºF)
The cleaner should never be operated outside of these temperatures or damage may occur.
2. The installation should be carried out in accordance to local safety standards and bylaws.
3. Any modification of the Admiral requires the prior consent from Waterco. Original replacement parts and accessories
authorised by the manufacturer ensure a high level of safety. Waterco assumes no liability for the damage and injuries caused by
unauthorised replacement parts and accessories.
4. The user should make sure that the installation is carried out by qualified authorised persons and that these persons have first carefully
read the following instructions.
Storing The Power Cord 7
General Maintenance 8
Winter Storage 8
Warranty 8-11
Trouble Shooting 12-13
Notes 14-15
2

5. The operating safety of the Admiral is only guaranteed if the installation and operation instructions are correctly followed.
6. In the event of defective operation or fault, contact Waterco or its nearest authorised service agent.
7. To reduce the risk of injury, do not permit children to use this product.
8. Incorrectly installed equipment may fail, causing severe injury or property damage.
9. Chemical spills and fumes can weaken the Admiral. Corrosion can cause the cleaner and other equipment to fail, resulting in severe
injury or property damage. Do not store pool chemicals near your equipment.
10. Do not play with the Admiral or power cable as potential entrapment of hair or body parts may result. The power cord can trip or entangle
swimmers which could result in drowning.
11. Your Admiral should not be used while people are swimming in the pool.
GENERAL INSTRUCTIONS
nMaximum Recommended Pool Size: 6m x 12m x 2.4m depth.
Minimum Recommended Pool Size: 3m x 3m.
nIf ambient air temperature exceeds 46ºC (115ºF), protect the Admiral’s power supply from direct sunlight. However, ensure power
supply has adequate ventilation.
nDo not connect the Admiral’s power supply (transformer) to AC power until installation has been completed.
nDo not use if unit is damaged in any way.
nMake sure the Admiral is unplugged from its power supply before opening the unit or performing any other maintenance.
nTo avoid damage to the power supply & power cord, never carry the power supply by the power cord or pull on the
power cord to disconnect from an outlet. Disconnect by pulling the plug, itself, from the outlet.
nDo not pull power cord around sharp corners or edges.
nDo not operate with a damaged power cord or power supply.
nBefore installing the Admiral, understand the cleaner’s coverage. The cleaner was not designed to automatically clean steps or to work
under solar covers. It was also not designed to do an initial clean up for a new pool installation.
nThe power supply must be at least 4m (12ft) from the pool’s edge at all times!
nIt is recommended that you clean your Admiral filter bag and check the impeller to make sure it is free and clear of debris
after every use.
nDisconnect the power supply from the outlet when not in use.
nDO NOT switch the Admiral to “ON” if it is not immersed in water. Operating the cleaner out of water may cause severe damage & will
result in loss of warranty. Always remember to turn the power supply “OFF” and unplug it from the power outlet before removing the
cleaner from the pool.
3

INSTALLATION
nEnsure power supply (transformer) is in the off position.
nPlug the power supply lead into its own dedicated 220-240V, 50Hz AC electrical outlet.
It is essential the power point is properly connected to an earth leakage circuit breaker and
properly earthed to ground. Consult a qualified electrician if you are unsure.
IMPORTANT NOTE:
The cleaners power supply is also equipped with a Residual-Current Device (RCD).
This device disconnects the power circuit whenever it detects that there is not a balance between
the power and the return neutral conductor. Such an imbalance is sometimes caused by current
leakage through the body of a person who is grounded and accidentally touching the powered part of the circuit and will prevent injury caused
by such shocks. They are not intended to provide protection against overload or short circuit conditions, the earth leakage circuit breaker below
will handle this situation.
WARNING:
It is strongly recommended that you test the RCD prior to using the cleaner power supply.
RCD OPERATION:
1. Plug power supply lead into dedicated electrical outlet.
2. Press RESET button and the indicator light should be on “Lite”.
3. Press TEST button and the indicator light should be on “Off”.
4. Press RESET button for use of the cleaner, do not use if TEST fails and indicator is on “Lite”.
n This RCD is not an overload protection device.
n This RCD device complies SAA AS/NZS3190, Approval No A/10643EA.
n Do not plug the power supply lead into an extension cord.
n Plug in the connector of the power cord from the cleaner into the power supply. The connector is keyed so that it will
only plug into the power supply one way. Make sure that the plug is pushed all the way onto the power supply.
Slide the connector lock (strain relief) onto the connector and turn the connector lock clockwise until it is tight (Do not over tighten).
WARNING:
1. DO NOT RUN THE CLEANER OUT OF THE WATER. OPERATING THE CLEANER OUT OF THE WATER WILL DAMAGE THE MOTORS AND VOID THE WARRANTY
2. THE ADMIRAL SHOULD NOT BE CONNECTED TO A TIMING DEVICE AND LEFT CONTINUOUSLY WITHIN A POOL OR SPA.
nPlace the Admiral into the pool and rock the cleaner side to side to
release any trapped air. The cleaner will sink to the bottom of the pool.
nPlace a sufficient length of the power cord into the water that will enable the
Admiral to easily reach all areas of the pool.
(Do not place ALL of the power cord into the pool unless required).
nTurn on power supply at dedicated 220-240V, 50Hz AC electrical outlet and switch power
supply to the on position, and the Admiral will begin its cleaning program.
nThe Admiral will automatically shut itself down after two hours.
nIf a second cleaning is required or the Admiral is accidentally shut off, you should wait one
minute before switching the cleaner on again. The cleaner has an automatic lock out
period to protect the electronic intelligent navigation devices.
IMPORTANT NOTE:
During normal operation, the cleaner will appear to shut off for a few seconds, raise the front
wheels off the pool bottom and move either left or right or turn for an undetermined amount of
time. This is normal and has been pre-programmed into the unit to assure the quickest and most
efficient cleaning of your pool.
4

REMOVING THE CLEANER FROM THE POOL
nSlowly pull the Admiral’s power cord to retrieve the cleaner to the water surface and pool edge.
(DO NOT PULL THE CLEANER OUT OF THE POOL BY THE POWER CORD).
nReach down and grasp the handle of the Admiral and remove it from the pool as shown in Fig 1 and Fig 2.
Note: The Admiral should be stored in an area that will afford some protection from the elements to insure that it retains its finish.
CLEANING THE ROBOTIC POOL CLEANERS FILTER BAG
Note: It is strongly recommended that the Admiral’s filter bag should be cleaned after every use.
nTurn the Admiral upside down and place on the ground or stable surface so the bottom lid is exposed.
nTurn the two front red locking pegs (a) inwards as indicated by the two arrows moulded into top lid to the unlocked position
as shown in Figure 3.
nNext press the two red locking clips inwards (b) located at the rear of the cleaner lid and lift the bottom lid out of cleaner housing.
nHold the bottom lid as shown in Figure 4 and pull the tab marked “PULL TO REMOVE BAG”
nTurn filter bag inside out and hose out all remaining debris as shown in Figure 5. If filter bag is very dirty it may be washed in
a washing machine.
Note: When using a washing machine it is recommended to turn the filter bag inside out and wash using cold water (only) and a mild detergent
without any other item within the wash.
Note: Do NOT use a clothes dryer.
nHose all debris out of the Admiral bottom lid being sure to remove all dirt from the fine filters situated on the intake doors as shown
in Figure 6.
5
Figure 1 Figure 2 Figure 3
Figure 4 Figure 5 Figure 6
a
b
b

nTo reattach the filter bag to the bottom lid, turn the filter bag right-side-out.
nStart at the back of the filter bag and bottom lid where the filter bag says
“Warning: Push bag behind bottom lid TAB” and insert the filter bead into the
channel, so that the tabs are holding the filter bag in near the label with
the words “Warning: Push bag behind bottom lid TAB”, as shown in Figure 7.
Note: Visually ensure the Admiral’s filter bag is correctly seated into the cleaner’s
bottom lid retaining channels particularly the corners. Refer Figures 7 - 7a
Note: Press the filter bag bead down all the way around the perimeter making sure
that it is completely seated and behind all the tabs as shown in Figure 7b.
WHEN REFITTING THE BOTTOM LID TO THE CLEANER, MAKE SURE ALL FILTER BAG
MATERIAL IS INSIDE THE CLEANER OTHERWISE THE LID WILL NOT CLOSE AND LOCK
INTO PLACE PROPERLY.
n Once the bottom lid is properly seated, turn the red locking pegs in the
opposite direction of the arrows moulded into the bottom lid until it locks
between the two raised locks. Refer Figure 7c.
n Press the rear section of the bottom lid into the cleaner while pushing the
locking clips towards the edge of the cleaner until an audible click is heard
as shown in Figure 7d.
Note: Ensure the Admiral’s filter bag is completely enclosed within the cleaner housing
as the bottom lid will not close properly, and the cleaner will not operate.
POWER CORD MAINTENANCE
In the course of using your Admiral, the blue power cord may become twisted or
tangled.
The Admiral Kink Resistant Power Cord Advantage
The Admiral Robotic Pool Cleaner has a specifically designed kink resistant
power cord using a one piece extruded technology that prevents the cord from
delaminating, protecting the internal wires from shorting out and extending it’s
operating life.
If you refer to the power cord (Fig 8 below), there are no layers as the cable & wires
are manufactured simultaneously. The coating of the cable is injected with air to form
small pockets that allow it to float, so the outer layer takes the place of (3) layers of
a typical cable.
Figure 7
Figure 7b
Figure 7a
6
Admiral Robotic Cleaner Cable
Foam Casing
Air Pockets
(Enlarged in diagram)
Wire Inner Core
(+/- coated in non-conductive material)
Fig 8
Note: Ensure Filter Bag bead is
located behind bottom lid tab.
Figure 7dFigure 7c
INCORRECT INSTALLATION

The following five points can prevent or greatly reduce the tangling of the power cord:
1) Make sure there are no objects in the pool during the cleaning cycle for the power cord to get caught on (pool ropes, toys, etc).
2) Only allow enough power cord in the pool for full coverage/do not put excess power cord in the pool
(Example 8m pool doesn’t need 15m of power cord).
3) The Admiral should not be connected to a timing devise and left continuously within a pool or spa.
4) Remove cleaner from the pool and uncoil the power cord from the power supply after every cleaning cycle to release the tension
in the power cord.
5) The Admiral is designed to work with water at a temperatures greater than 13ºC (55ºF) and less than 45ºC (113ºF).
The cleaner should never be operated outside of these temperatures or damage may occur.
To uncoil the power cord, it is best that the cord is wet:
1. Place the cleaner on the ground as shown in Fig 9.
2. Unplug the power cord from the power supply.
3. Be sure to use a clear area that will allow the power cord to stretch out in a straight line.
4. Pull the power cord so it is off the ground.
5. Using your fingers, roll the power cord in the opposite direction that it is coiled in.
6. When straight, loop power cord for storage as shown in Fig C.
STORING THE POWER CORD
1. Unplug the power cord from the power supply.
2. Hold the power cord close to the cleaner. Refer Fig A.
3. Make a roughly half metre (two feet) loop with the power cord as shown. Refer Figure B.
4. When making loops, roll the power cord slightly in a counter clockwise manner
to maintain form as shown in Fig C.
Note: Do not loop the power cord tightly around objects.
Note: When looping the power cord for storage it is best to start close to the cleaner rather
than at the power connection end. Refer Fig A. Hold the power cord as close to the cleaner as possible
and loop the power cord to the cleaner. Refer Figures B & C
Figure 9
Figure A
Figure B
Figure C
7

GENERAL MAINTENANCE GUIDE
To ensure the maximum life of the Admiral Robotic Pool Cleaner, please follow the procedures below:
1. Clean The Admiral Robotic Pool Cleaner filter bag after every use.
2. Maintain a correct chemical balance of your pool/spa water. The chemical balance of water is a relationship between its pH,
total alkalinity, calcium hardness and water temperature.
The water must be maintained at all times to the following:
PH LEVEL : BETWEEN 7.2 & 7.8.
TOTAL ALKALINITY : BETWEEN 80 & 150ppm.
CALCIUM HARDNESS : BETWEEN 150 & 300ppm.
Also, within these tolerances be balanced to the Langelier Saturation Index within a range of -0.2 to +0.2.
Note: Testing kits are available to test the water yourself or alternately bring a sample of the water to a professional pool and spa shop.
n Mains water and rural water supplies need to be monitored. Saturation (life) in mains water or bore (rural) will vary depending
on water quality.
WINTER STORAGE
If temperatures will regularly be below 5ºC (41ºF) or over 45ºC (113ºF), the cleaner and power supply (transformer) should be stored indoors.
WARRANTY
The Waterco Admiral has been manufactured, tested and inspected in accordance with carefully specified engineering requirements. It is
warranted to be free from defects in materials and workmanship under normal use and service, subject to qualifications, conditions and
limitations described below.
2 Year Limited Warranty:
2 Year full warranty. This warranty applies only while using this product in Australia & New Zealand. This warranty extends to the first consumer/
purchaser for a period of 2 Years from the original date of purchase.
This warranty covers only normal and reasonable use. Any damage, defects, malfunctions or other failures arising from its use without the
original transformer or any use which does not comply with the instructions in this manual, including failure of the purchaser to provide
reasonable and necessary maintenance, will void this warranty.
The warranty obligations of Waterco Ltd shall be limited to repair or replacement of the product or any defective component, at the discretion
of Waterco Ltd. The repair or replacement may include the use of refurbished components and/or units. Waterco Ltd will not be liable or
responsible under any circumstances or in any amount for any consequential or incidental damages, for any injury or damages to persons or
property using or used in connection with this product, or for loss of profits or other costs or expenses of any kind or character.
This warranty does not include replacements of the filter bag, bottom lid, brushes and tracks.
CAUTION:
Some pool vinyl liners are more susceptible to surface wear and pattern removal than others, caused by objects such as brushes, toys, floats,
chlorine dispensers, and automatic pool cleaners coming into contact with the pool vinyl surface.
Such patterns can be easily scratched or abraded merely by rubbing the surface with a brush. Pattern ink can also rub off when they come
into contact with objects in the pool. Waterco Ltd is not responsible for, nor does this limited warranty cover pattern removal, abrasion, and
markings on or damage to any kind of pool vinyl liner.
[Important note: you may have additional rights under warranties mandated by the Trade Practices Act or similar legislation].
8

PLEASE READ
1. These terms and conditions carefully, as failure to comply may affect your legal rights under this warranty; and
2. Any operation instructions carefully before commencing use of any product manufactured/Distributed by Waterco Limited (“Waterco”). Waterco
manufactures quality pool and spa products to the highest standards using the most advanced technology and production procedures available.
WARRANTY COVER
If a defect occurs in any Waterco product during the warranty period, Waterco will at its discretion, repair the product or replace and install
the defective part, free of charge provided that the defect results solely from poor workmanship or materials and subject to these terms and
conditions.
Labour is covered by this warranty for a period of 2 years from the date of purchase or installation, within a 25 km (15 miles) radius of an
authorised Waterco Service Agent.
The purchaser is responsible for any freight incurred.
Warranties are valid only within the original country of purchase. Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law [applicable only to Australian States and Territories]. You are entitled to a replacement or refund for a major failure and
compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if goods fail to
be of acceptable quality and the failure does not amount to a major failure.
WARRANTY PERIOD
Waterco Admiral Robotic Pool Cleaners are covered by a two year warranty.
All warranty periods commence on the date of purchase by the end user.
The provisions of this warranty are not transferable and are in addition to and not in modification of or subtraction from any applicable
statutory warranties, rights or remedies.
CONDITIONS OF WARRANTY
This warranty only applies where:
1. The products requiring installation have been sold with installation included and have been installed by a licenced plumber, electrician or
person who has completed an accredited course in swimming pool care and maintenance or a person with more than 1 year on the job
learning or a person supervised by one of these people, in accordance with any written installation instructions provided.
2. The products have been installed and operated in accordance with written instructions supplied by Waterco;
3. The purchaser is able to provide proof of purchase that specifies the date of purchase;
4. The product has been serviced or maintained regularly. (at least once a month).
5. Any pool and spa equipment has been used in water:
a. With a temperature not exceeding 40ºC (104ºF);
b. With a pH range maintained between hte pool water chemistry above mentioned 7.2 to 7.8;
c. That has been chemically balanced in accordance with the Langelier saturation index within a range of -0.2 to + 0.2 to ensure that it is
not corrosive or scale forming;
d. That is not salt water (other than mild saline water conditions which are compatible with swimming pool salt water chlorination systems) –
unless otherwise stated by Waterco in both the respective product labels and brochures that it is suitable for seawater applications; and
e. That has been regularly treated with a sanitising system using bromine, chlorine in one of its compound forms, or generated in-situ,
in concentrations (doses) recommended by the relative state or territory health departments. (In areas outside of Australia please refer to
the local health department recommendations before use);
6. Electrical equipment has been adequately protected from salt air environments and from salt water; and
7. All repairs and replacements shall be carried out by Waterco or its authorised service dealer, unless otherwise authorised in writing
by Waterco.
8. If an authorised service dealer is not available within 25 km (15 miles) of the purchaser’s area:
• The purchaser must contact the place of purchase or Waterco for further instructions and;
• The purchaser is responsible for any freight or infield labour costs.
9

EXCLUSIONS
This warranty does not cover, and Waterco will not be responsible for, any defect or damage caused or contributed to by:
(a) installation or use of the product other than in accordance with Waterco’s written instructions, any statutory requirements and these
terms and conditions;
(b) use of the product for a purpose other than for which it was designed or sold;
(c) abuse, misuse, corrosion, internal and external, or normal wear and tear;
(d) any repairs or modifications whatsoever carried out by any person, other than a Waterco authorised service dealer;
(e) exposure to water not caused by a defect in the product; and
(f) transit of the product over which Waterco has no control.
(g) inadequate ventilation
(h) cement, pebbles, render or other pool surface finishes blocking the pump’s impeller
(i) insect and/or vermin infestation
To the extent permitted by law Waterco excludes all liability it may have to the purchaser for indirect, special or consequential loss arising from
or related to any defect in any Waterco product, or any act or omission, including negligence of Waterco, including, but not limited to, loss of
business, loss of profit, loss of revenue, lost opportunity, inconvenience, and damage to any property other than the
Waterco product.
To the extent permitted by law, Waterco excludes all other conditions, guarantees, liabilities or representations that are not expressly set out in
this agreement. These terms and conditions do not attempt to exclude, restrict or modify any applicable statutory rights, or any exercise of any
statutory rights, or any liability imposed on Waterco by any law (including the Competition and Consumer Act 2010), if to do so would contravene
that law or make any part of these terms and conditions void.
To the extent permitted by law, Waterco excludes all conditions and warranties implied into these terms and conditions and limits its liability for
breach of any such condition or warranty that it cannot exclude to the greater of (at Waterco’s option);
(a) for goods:
• Repairing or replacing those goods; or
• Paying the cost of having those goods repaired or replaced; and
(b) for services:
• Resupplying the services; or
• Paying the cost of having those services resupplied.
TEST YOUR WATER REGULARLY
The chemical balance of the water is a relationship between total alkalinity, pH, calcium hardness and temperature. Waterco recommends that
you have your water tested regularly by your local pool professional. A record of testing should always be kept for reference.
Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so any such limitation may not apply.
This warranty gives specific legal rights. The purchaser may have other rights depending on the jurisdiction in which the Waterco product was
purchased or the purchaser is located.
Product Warranty Exclusions
Admiral Robotic Pool Cleaner 2 Year 1. Leaving cleaner in direct sunlight & out of water
2. Human intervention damaging the cleaner
3. Normal wear & tear
4. Colour fading due to sun
5. Water chemistry out of normal range
Drive Motor and Pump Motor 2 Year 1. Human intervention damaging the cleaner
2. Water chemistry out of normal range
Filter bag, bottom lid, brushes & tracks Excluded 3. Normal wear & tear component
10
Table of contents
Other Waterco Swimming Pool Vacuum manuals


















