Vivo STAND-V103 User manual

Triple Monitor Desk Mount

Scan the QR code with your mobile device or follow the link

for helpful videos and specifications related to this product.

Instruction Manual

https://vivo-us.com/products/stand-v103

SKU: STAND-V103

[email protected]om www.vivo-us.com 309-278-5303

Chat live with an agent!

GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

WARNING!

If you do not understand these directions, or if you have any doubts about the safety of the installation,

please call a qualified technician. Check carefully to make sure there are no missing or defective parts.

Improper installation may cause damage or serious injury. Do not use this product for any purpose that is

not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or

injury caused by improper mounting, incorrect assembly or inappropriate use.

TIPOVER WARNING

SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:

• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.

• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL

USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.

WARNING: CHOKING HAZARD

SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

22 lbs

Per Arm

(10 kg)

DO NOT EXCEED WEIGHT CAPACITY.

Failure to do so may result in serious injury.

PACKAGE CONTENTS

A (x1)

Pole

B(x1)

Lower Clamp

C(x1)

Upper Clamp

D(x1)

Pole Cover

E(x1)

Arm

G (x4)

Joint Cover

H(x4)

Plastic Spacer

S-B (x2)

M10x15mm

Screw

S-D (x2)

M8x10mm

Screw

S-F (x1)

M10 Bolt

I (x1)

Support Plate

S-E (x1)

M10 Washer

S-G (x1)

Lock Washer

L (x1)

Grommet Pad

M-A (x12)

M4x12mm

Thumbscrew

M-B (x12)

M4x30mm

Screw

M-C (x12)

M4 Spacer

N (x2)

Spare Cap

T-D (x1)

Wrench

K (x2)

Side VESA Plate

J (x1)

Center VESA Plate

S-I (x2)

Cap Nut

S-H (x1)

M4x6mm

Screw

M (x4)

Cable Clip

F(x2)

Arm Extension

S-C (x2)

M10x47mm

Screw

S-A (x3)

M6x8mm

Screw

T-A (x1)

3mm Allen

Wrench

T-B (x1)

5mm Allen

Wrench

T-C (x1)

6mm Allen

Wrench

NOTE: SOME HARDWARE MAY NOT BE USED

TOOLS NEEDED

Phillips

Screwdriver Drill

ASSEMBLY STEPS

STEP 1 - Clamp Installation

Install Upper Clamp (C) to Pole (A) using M6x8mm Screws (S-A) and a Phillips screwdriver.

Assemble Lower Clamp (B) to Upper Clamp (C) using M10x15mm Screws (S-B) and 5mm

Allen Wrench (T-B). Secure the clamp assembly to the desktop be tightening to the hand

bolts on Lower Clamp (C). Install the Pole Cover (D) to Pole (A).

S-A

S-B

T-B

STEP 1 - Grommet Installation

Remove adhesive backing from Grommet Pad (L) and place on the bottom of Pole (A).

Install Pole (A) to existing grommet hole using Support Plate (I) with M10 Bolt (S-F),

M10 Washer (S-E) and Lock Washer (S-G). Tighten with Wrench (T-D). Install the Pole

Cover (D) to Pole (A).

S-E

S-G

T-D

S-F

If no grommet hole exists, drill a 3/8” (10mm) diameter hole through the mounting

surface.

STEP 2

Align Arm and Arm Extension (E,F) so that the holes for the cable clips are facing

down. Insert Monitor Arms (E) into Arm Extension (F) as shown below. Secure using

M10x47mm Screws (S-C) and 6mm Allen Wrench (T-C).

Press Monitor Arm Covers (G) onto the top and bottom of arm joints. Place Cable Clips (M)

into wire clip holes

Cable Clip

Hole

Cable Clip

Hole

Cable Clip

Hole

NOTE: Transparent monitor arm image used to show wire

clip holes. Holes are on the underside of arms and are not

visable when arm is facing upright.

Cable Clip

Hole

Cable Clip

Hole

Cable Clip

Hole

Lay Arm (E) on flat surface with holes for cable clips facing down. Add Plastic Spacers

(H) to holes at ends of Arm (E).

NOTE: Transparent monitor arm image used to show cable clip holes. Holes are on the underside of

arms and are not visable when arm is facing upright.

S-C

T-C

STEP 3

Slide arm assembly onto Pole (A) at desired height and secure using M8x10mm

Screws (S-D) and 5mm Allen Wrench (T-B).

Center VESA Plate (K) Installation

STEP 4a - Flat Back Monitors

Side VESA Plate (J) Installation

Attach the Center VESA Plates (K) to the monitors you intend to mount in the center of

the mount. Attach Side VESA Plates (J) to remaining monitors. Secure using M4x12mm

Screws (M-A).

M-A

NOTE: Hand tighten screws to avoid stripping the plastic screw heads.

S-D

T-B A

STEP 4b - Curved/Recessed Back Monitors

Attach the Center VESA Plates (K) to the monitors you intend to mount in the center of

the mount. Attach Side VESA Plates (J) to remaining monitors. Secure using M4 Spacers

(M-C), M4x30mm Screws (M-B) and a Phillips screwdriver.

Center VESA Plate (K) Installation Side VESA Plate (J) Installation

M-BM-B

M-C

STEP 5

S-H

Slide the center monitor onto the Center Head (C1) of Monitor Arm (C). Install M4x6mm

Screws (S-E) to secure the monitor.

STEP 6

Slide the outer monitors onto Outer VESA Heads (C2).

Secure with Cap Nut (S-I).

S-I

Adjust Monitor Tilt

Pry o Plastic Covers (C3) from the Outer VESA Heads (C2).

The exposed nut on the side is used to adjust the tilt. Tighten

the nut using Wrench (T-D) to adjust.

Replace Plastic Covers (C3).

To adjust center monitor swivel or tilt,

use 3mm Allen Wrench (T-A) to loosen

center set screw on the Center Head

(C1), as shown at le.

T-D

T-A

Adjust Monitor Height

To adjust center monitor height, turn

the screw behind Center Head (C1)

using the 5mm Allen Wrench (T-B).

To level the side monitors,

remove the Cap Nut (S-I) and

turn the inner bolt with the 3mm

Allen Wrench (T-A) to raise or

lower the monitor. Replace Nut

aer the adjustment.

T-A

Cable Management

Manage cables using Cable Clips (M) on assembled arms. Remove the split cap from the

Pole (A) and feed cables through, pulling ends out from the opening in back. Replace the

split cap when finished.

Other manuals for STAND-V103

Table of contents

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 