Vivo STAND-E-102B User manual

Electric Height Adjustable Dual Monitor Stand

Scan the QR code with your mobile device or follow the link

for helpful videos and specications related to this product.

Instruction Manual

https://vivo-us.com/products/stand-e-102b

SKU: STAND-E-102B

[email protected]om www.vivo-us.com 309-278-5303

Chat live with an agent!

GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

PACKAGE CONTENTS

22lbs

(10kg)per arm

DO NOT EXCEED WEIGHT CAPACITY.

Failure to do so may result in serious injury.

WARNING!

If you do not understand these directions, or if you have any doubts about the safety of the

installation, please call a qualied technician. Check carefully to make sure there are no missing or

defective parts. Improper installation may cause damage or serious injury. Do not use this product

for any purpose that is not explicitly specied in this manual. Do not exceed weight capacity.

We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or

inappropriate use.

NOTE: SOME HARDWARE MAY NOT BE USED

F (x1)

Single Arm

Bracket

G (x4)

Arm Cable Clips

H (x2)

VESA Plate

S-A (x4)

M6x12mm

Screw

S-B(x2)

Screw Cap

S-C (x2)

M3x8mm

Screw

M-A (x8)

M4x12mm

Screw

WARNING: CHOKING HAZARD

SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

TOOLS NEEDED

Phillips

Screwdriver

Pencil

SUPPORTED MONITOR RANGES :

Most 20” - 32” screens

Scissors

A (x1)

Electric Stand

B(x1)

Lower Clamp

Bracket

C(x1)

Upper Clamp

Bracket

D(x1)

Clamp Cable Clip

E(x1)

Dual Arm

I (x1)

Cable Sleeve

M-C (x8)

M5 Washer

T-A (x1)

4mm Allen

Wrench

M-B (x8)

M5x12mm

Screw

T-B (x1)

6mm Allen

Wrench

ASSEMBLY STEPS

STEP 1

Attach Upper Clamp Bracket (C) to the bottom of the Electric Stand (A) using M6x12mm

Screws (S-A) and a 4mm Allen Wrench (T-A).

STEP 2

For desktops between 10-55mm (0.40”-2.15”), align the key slots on Lower Clamp

Bracket (B) with the screws on Upper Clamp Bracket (C). Pull Lower Clamp Bracket (B)

down and lock the screws on Upper Clamp Bracket (C) in place with the 4mm Allen Wrench

(T-A).

For desktops between 50-85mm (2”-3.35”), remove the screws on Upper Clamp Bracket

key slots on Lower Clamp Bracket (B) with the screws on Upper Clamp Bracket (C). Pull

Lower Clamp Bracket (B) down and lock the screws on Upper Clamp Bracket (C) in place

with the 4mm Allen Wrench (T-A).

S-A

T-A

STEP 3

First, clamp the stand assembly onto desk. Press the Clamp Cable Clip (D) onto Upper

Clamp Bracket (C).

Option A: Dual Monitor Setup

STEP 4

Partially loosen screw on Dual Arm (E) with 6mm Allen Wrench (T-B) and slide Dual Arm (E)

onto the post of Electric Stand (A).

T-B

STEP 5

Re-tighten screw on Dual Arm (E) with arm assembly at the top of the post using the 6mm

Allen Wrench (T-B). Attach an Arm Cable Clip (G) onto each arm segment.

Note: The nal arm position will be determined in step 13.

STEP 6

Remove a single arm segment and the cable clip from Dual Arm (E) using the 6mm Allen

Wrench (T-B).

Single Arm

Segment

T-B

Cable Clip

Option B: Single Monitor Setup

T-B

STEP 8

Attach the single arm segment to Single Arm Bracket (F) using the 6mm Allen Wrench (T-B).

Note: This screw adjusts the joint tension. The tighter the screw the more resistance there

will be when pivoting the arm.

STEP 7

Loosely assemble the cable clip on Single Arm Bracket (F) using the 6mm Allen Wrench

(T-B).

Cable Clip

Single Arm Segment

Washer

Arm Screw

Clip Screw

T-B

STEP 10

Attach VESA Bracket (H) to monitors using either M4x12mm or M5x12mm bolts (M-A,M-B)

and Washers (M-C) along with a Phillips Screwdriver.

Monitor Installation

T-B

STEP 9

Re-tighten screw on Single Arm Bracket (F) with arm assembly at the top of the post using

the 6mm Allen Wrench (T-B). Attach an Arm Cable Clip (G) onto each arm segment.

Note: The nal arm position will be determined in Step 13.

STEP 11

STEP 12

Connect the DC plug on the splitter cable into the base of Electric Stand (A). Connect USB

coming from the desk control panel into the base of Electric Stand (A). Make sure the USB

cord is ran outside of the cable clip. Refer to the frame manual to plug in the remaining

cables.

S-B

S-C

Slide monitors onto tilt joint located on the arm assembly. Lock VESA plate (H) in place

with Screw Cap (S-B), M3x8mm Screw (S-C) and a Phillips Screwdriver. Adjust monitor

height alignment by turning Screw Cap (S-B) by hand or using 6mm Allen Wrench (T-B).

Note: If you are having an issue with a monitor tilting down once installed on the arm,

refer to Step 17 to tighten down the tilt joint.

Control Panel

DC Plug Splitter Cable

USB

T-B

STEP 13

Initial Setup Procedure:

Referring to the control panel instruction manual, ensure the panel display is set to adjust

frame height (see the “Shi Device Display” section) and move your desk frame to a

comfortable level for your normal sitting position. It is recommended to follow general

ergonomic guidelines for working posture while considering your desk frame height. Store

this position in memory setting 1.

Next, with the electric stand at its lowest height setting, loosen the arm bracket screw

using the 6mm Allen Wrench (T-B) and manually adjust the arm assembly along the

electric stand post until the top of the monitor screen is at eye level while in your normal

sitting position. If this is not possible due to being taller or shorter than average, simply

position the arm assembly at the very top or the very bottom of the electric stand post

respectively. Re-tighten the arm bracket screw to secure the arm assembly in this position.

Note: You do not have to use the monitor at this height, but doing so reduces the amount

of manual adjustment later on.

T-B

STEP 14

Setting Memory Positions:

Referring to the control panel instruction manual, ensure the panel display is set to adjust

stand height. In your normal sitting position, move the stand until the monitors are at a

comfortable level, switching between frame and stand adjustment on the panel display

as necessary. It is recommended to follow general ergonomic guidelines for work posture

while considering the optimal height of your monitors. Store this position in memory

setting 1. Your desk and monitor height should both now be synced to memory setting 1.

Referring to the control panel instruction manual, move your desk frame and monitor to

a comfortable standing position, switching between frame and stand adjustment on the

panel display as necessary. Store these height locations to memory setting 2. Repeat this

procedure for storing a third working posture in memory setting 3 if desired.

Other manuals for STAND-E-102B

Table of contents

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 