Vinten Vision 8 Manual

Vinten

Camera Control Solutions

Operators Guide

Vision 8

Pan & Tilt Head

Vision 8

Pan and Tilt Head

Publication Part No. 3441-8 Issue 4

or reproduced in any way including, but not limited to, photocopy, photograph, magnetic or other record without the prior

agreement and permission in writing of

Vinten Broadcast Limited.

Vinten and Vision are registered trademarks of Vinten Broadcast Limited.

Safety - read this first

Warning Symbols in this Operators Guide

Where there is a risk of personal injury, injury to others, or damage to the pan

and tilt head or associated equipment, comments appear, highlighted by the

word WARNING! and supported by the warning triangle symbol.

Technical data

Weight

Head 2.7 kg (5.9 lb)

Pan bar 0.2 kg (0.4 lb)

Bowl clamp 0.14 kg (0.3 lb)

Height to mounting face 15 cm (5.9 in.)

Length 14 cm (5.5 in.)

Width 12.5 cm (4.9 in.)

Typical payload 10.5 kg (23 lb) - See balance graph

Tilt range ±90°

Pan range 360°

Tripod fixing 100 mm ball

Further information

For further information or advice regarding this pan and tilt head, please contact Vinten Broadcast

Limited, your local Vinten distributor (see back cover) or visit our website.

For full details on maintenance and spare parts, please refer to the Vision 8 Pan and Tilt Head

Maintenance Manual and Illustrated Parts List (Publication Part No. 3441-9) This is obtainable

from Vinten Broadcast Limited or your local Vinten distributor. For information on-line, visit our

website at

www.vinten.com.

Contents

Page

Safety - read this first . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Further information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Operation

Installing the head on a tripod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Mounting the camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Balancing the head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Pan and tilt brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Pan and tilt drag. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Servicing

Routine maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Battery replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Brake knob and drag control knob adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Parts list. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Associated publication

Vision 8 Pan and Tilt Head

Maintenance Manual

Publication Part No. 3441-9

(1) Pan bar

(2) Balance knob

(3) Pan drag adjustment knob

(4) Switch for illuminated level bubble

(5) Pan brake knob

(6) Pan bar mounting

(7) Tilt brake knob

(8) Slide lock release

Vision 8 (Left-Hand Side)

(8) (1)

(2)

(3)

(4)

(7)

(6)

(5)

(9) Slide plate

(10) Slide plate clamp

(11) Tilt drag adjustment knob

(12) Bowl clamp

(13) Illuminated level bubble

(14) Battery compartment

(15) Camera mounting screws

Vision 8 (Right-Hand Side)

(9)

(10)

(11)

(13)

(15)

(14)

(12)

Introduction

The Vision 8 pan and tilt head embodies an adjustable spring counterbalancing mechanism, LF

drag assemblies for pan and tilt motions and an adjustable camera mounting plate.

The balance system is easily adjusted by a knob (2) on the rear of the head. Maximum and mini-

mum payloads that can be balanced, and tilt ranges, are dependent on the weight of the camera

and accessories and on the centre of gravity (C of G) height.

The graph shows the range of load and C of G height that can be maintained in balance. The shad-

ed area of graph corresponds to those load/C of G combinations that can be balanced over the

full tilt range. The areas to the right indicate the progressively reducing tilt range with greater load

and higher C of G.

Where a load/C of G combination falls outside of the graph it will be necessary to increase or de-

crease the weight or the C of G height - if possible - to enable the head to balance the load.

Balance graph

8200

in. mm

±90°

±60°

±40°

190

180

170

160

150

140

130

120

100

110

46810 12 14 16 18 20 22 kg

812 16 20 24 28 32 36 40 44 48 lb

Both the pan and tilt mechanisms incorporate the patented Vinten lubricated friction (LF) system

to ensure smooth movement of the camera about these axes and are fitted with control knobs (3,

11) to adjust the drag setting.

The whip-pan facility is unaffected by the pan drag setting.

Friction brakes on each axis allow the head to be locked at any chosen position. The operating

knobs for both brakes (5, 7) are fitted at the left-hand side of the head.

An illuminated level bubble (13) is fitted to the rear of the head. When the switch (4) is pressed,

the bubble will be illuminated for 15 seconds. The battery for the illuminated bubble is contained

in a battery compartment (14).

Pan bar mounting points (6) are located at the rear of the head, on either side of the camera

mounting platform. The pan bar is attached using a pan bar clamp, with angular adjustment avail-

able on the mount serrations. A fixed pan bar (1) is supplied. A second pan bar may be fitted.

The camera is attached to the head by means of a slide plate (9) or by using the optional Quickfit®

adapter (see Mounting the camera). A clamp (10) is provided to hold the slide plate in position

and a lock (8) prevents its inadvertent removal from the head.

Operation

Installing the head on a tripod

The Vision 8 pan and tilt head is supplied with an integral 100 mm ball mount, designed for instal-

lation on a compatible Vinten Vision tripod.

Adaptors are available which enable the head to be installed on tripods or pedestals fitted with

other mountings. These are listed under ‘Optional Accessories’.

To install the head, remove the bowl clamp assembly (12) from the head, position the head on the

tripod and refit the bowl clamp assembly from below. Level the head with the aid of the level bub-

ble (13) and tighten the bowl clamp. The level bubble may be illuminated by pressing the switch

(4). The light will extinguish after approximately 15 seconds.

Mounting the camera

Mounting the camera(3/8 in. mounting screws)

Remove the slide plate (9) from the head by releasing the slide plate clamp (10), pressing the slide

lock release (8) and pulling the plate out to the rear.

Attach the slide plate to the camera or camera mounting plate under the approximate centre of

the camera's weight using both mounting screws (15).

Set the platform level and apply both the pan and tilt brakes (5, 7).

Push the slide plate and camera into the track in the platform, ensuring the slide lock release (8)

snaps into position.

Balance the head (see Balancing the head).

Mounting the camera (VHS adaptor)

The optional VHS adaptor (21) consists of a VHS pin and a 1/4 in. BSW camera mounting screw

connected by a plastic link.

To mount the camera using the VHS adaptor, proceed as follows:

Remove the slide plate (9) from the head by releasing the slide plate clamp (10), pressing

the slide lock release (8) and pulling the plate out to the rear.

Remove the two 3/8 in. BSW camera mounting screws (15) from the slide plate.

Position the VHS (21) adaptor in the longer slot in the slide plate, with the pin facing for-

wards. Screw the pin securely into the slide plate.

Secure the slide plate to the camera with the 1/4 in. BSW camera mounting screw, ensuring

the pin engages in the hole in the camera.

Set the platform level and apply both the pan and tilt brakes (5, 7).

Push the slide plate and camera into the track in the platform, ensuring the slide lock re-

lease (8) snaps into position.

Balance the head (see Balancing the head).

Mounting the camera (optional Quickfit adaptor)

If not already attached, secure the Quickfit Adaptor (18) to the slide plate (9) with the two screws

(15) provided.

Free the Quickfit wedge (17) from the adaptor by simultaneously pushing in on the safety catch

(20) and operating the wedge release (19).

Fit the Quickfit wedge to the camera with the two screws (16) provided.

Insert the forward end of the wedge into the forward end of the adaptor. Lower the rear of the

wedge into the adaptor until an audible click indicates that the wedge is locked in position.

Balance the head (see Balancing the head).

Mounting the camera (VHS adaptor)

(9)

(21)

(10)

(15)

(8)

Other manuals for Vision 8

Table of contents

Other Vinten Camera Accessories manuals

Vinten

Vinten Vision 6 Manual

Vinten

Vinten OB Quattro Manual

Vinten

Vinten Fulmar Pedestal User manual

Vinten

Vinten vector 750 Manual

Vinten

Vinten Vision Pozi-Loc 3880-3 Manual

Vinten

Vinten Protouch PRO-6 HDV Manual

Vinten

Vinten Protouch Pro-6HDV System Manual

Vinten

Vinten vector 750 User manual

Vinten

Vinten Vision Ped Plus Manual

Vinten

Vinten PRO-5Plus Manual

Vinten

Vinten flowtech 75 User manual

Vinten

Vinten V4109-0001 User manual

Vinten

Vinten HS-105P Instruction Manual

Vinten

Vinten Vector 90 Manual

Vinten

Vinten AutoCam SP-2000/X-Y Instruction Manual

Vinten

Vinten Vision blue5 User manual

Vinten

Vinten Vision 8 User manual

Vinten

Vinten FH155 Manual StarTracker User manual

Vinten

Vinten 3320 User manual

Vinten

Vinten Quattro-OBL Manual

Vinten

Vinten Vision Pozi-Loc User manual

Vinten

Vinten Vision Blue Manual

Vinten

Vinten pro-touch Pro-10 System User manual

Vinten

Vinten Osprey Plus User manual

Popular Camera Accessories manuals by other brands

Viltrox

Viltrox EF-NEX Mount instructions

Calumet

Calumet 7100 Series CK7114 operating instructions

Ropox

Ropox 4Single Series User manual and installation instructions

Cambo

Cambo Wide DS Digital Series Main operating instructions

Samsung

Samsung SHG-120 Specification sheet

Ryobi

Ryobi BPL-1820 Owner's operating manual

Aegis

Aegis ABL-36020P user manual

Pentax

Pentax Data Back Fc operating manual

Fantasea

Fantasea EyeGrabber F Series instruction manual

Honeywell

Honeywell HDZ20HD user manual

EGO

EGO BA1400T Operator's manual

Sima

Sima SRW-62 user guide

Shape

Shape A7SSMKIT Assembly manual

Slide Kamera

Slide Kamera HST-2 user manual

Power works

Power works 2902613 Original instructions

SES

SES SE-2047-2 user manual

Olympus

Olympus PT-EP05L instruction manual

Starlite

Starlite OctoDome nxt instructions