Vintage view Evolution Wine Wall Post User manual

Evolution Wine Wall Post

Installation instructions for floor-to-ceiling post for Wine Wall racking

• 1 Post base

• 1 Post top

• 24 Self-drilling screws

• Drill bit

• Phillips head driver/drill

• Level

• Pencil

• Tape measure

• Metal cutting saw

• Metal ﬁle

Parts List Required Tools

Fasteners:

Fasteners for securing racks to the Wine Wall Posts are provided (self-drilling screws).

Each mounting plate is pre-drilled for installing to the ceiling or ﬂoor. Please use the following recommendations

for fasteners:

• Drywall: Attach to joists or wood backing when available with a #8 X 1¼” course thread screw or larger or

use expanding hollow wall anchors with at least #8 screw size

• Wood: Use #8 X 1¼” course thread screws or larger

• Concrete, Brick or Stucco: 3/16” x 1¼” masonry screw or #8 x 1¼” screw with appropriate size expand-

ing concrete anchor

Figure A

Figure B

1. Build Wine Wall Racking: Follow instruc-

tions provided with Evolution Wine Wall racking (sold

separately) to assemble required racking for project.*

2. Measure ceiling height and mark Post:

Measure the ceiling height in the place where the

post is to be installed. Lay each section, interlaced, as

shown above (Figure A). Position the post so that the

measurement from top to bottom of the base plates

equals your ceiling height. Mark the top post section.

3. Cut Post: Using a reciprocating saw, band

saw or hack saw, squarely cut Post at marks from

Step 2 (Figure B). Repeat steps 2 and 3 for second

post.

Don’t use abrasive saws as they may damage ﬁnish!

* See following page for instructions using Extensions

Instructions

3. Assemble the Post: Slide the Post together, securing it to

each bracket of assembled Evolution Wine Wall rack (Figure C).

4. Install the Post & Rack: Stand the Post and rack combo

in the desired location and ensure it is plumb both front-to-back and

side-to-side using a level. Attach the mounting plate to the ceiling

using the appropriate fasteners for the ceiling material (Figure D).

Double check that the post is plumb with a level and secure the

mounting plate to the ﬂoor.

5. Add Wine: Only the good stuff.

Figure C

Figure D

For installations using Wine Wall Extensions

Skip Step 1, and after measuring and cutting Posts (Steps 2 & 3),

use the following steps:

4x. Assemble the Posts: Slide the Post together, securing it to

each bracket of an Evolution Wine Wall rack (Figure C).

5x. Install the rst Post: Stand the ﬁrst Post with one end of

Wine Wall racking attached in the desired location and ensure it is

plumb, both front-to-back and side-to-side, using a level. Attach the

mounting plate to the ceiling using the appropriate fasteners for the

ceiling material (Figure D). Double check that the post is plumb with

a level and secure the mounting plate to the ﬂoor.

6x: Assemble “Guide Rods”: Following Wine Wall Exten-

sion (sold separately) instructions, install three sets of Wine Rods the

Instructions

bracket at the top, middle, and bottom of each Wine

Wall rack height (Figure F). These will serve as “guide

rods’ to line up the next Post.

7x: Line up next Post: Measure 39 1/2” to

the next Post location* — centerline to centerline —

and use “guide rods” to properly align. *Adjust the

measurement width for any custom-cut wine rods.

8x: Fasten “guide rods”: Following Wine

Wall instructions, attach the other end of the “guide

rods” to the second post. Ensure Post and Rods are

plumb before fastening tightly and securing base

plates into ﬂoor and ceiling. Then install all remaining

rods.

9x: Repeat: Continue steps 5x-8x for as many

Wine Wall Extensions needed.

10x Add wine: Only the good stuff.

For additional support, visit www.vintageview.com

Figure E

Table of contents

Other Vintage view Rack & Stand manuals

Vintage view

Vintage view IDR Series User manual

Vintage view

Vintage view W Series User manual

Vintage view

Vintage view Vino Series User manual

Vintage view

Vintage view Le Rustique User manual

Vintage view

Vintage view FCF-2WB User manual

Vintage view

Vintage view W Series User manual

Vintage view

Vintage view W Series User manual

Vintage view

Vintage view W Series User manual

Vintage view

Vintage view W Series User manual

Vintage view

Vintage view LP-FCP-10 User manual

Vintage view

Vintage view W Series User manual

Vintage view

Vintage view W Series User manual

Vintage view

Vintage view W Series User manual

Vintage view

Vintage view W Series User manual

Vintage view

Vintage view FCF-HD User manual

Vintage view

Vintage view W Series User manual

Vintage view

Vintage view Flex Vino Series User manual

Vintage view

Vintage view W Series Single User manual

Vintage view

Vintage view Vino Flex Series User manual

Vintage view

Vintage view IDR3 User manual

Vintage view

Vintage view Half Island User manual

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 