Viavi OneAdvisor-1000 User manual
VIAVI//Public
OneAdvisor-1000 Portable Network Tester
OneAdvisor-1000 Portable Network Tester
QUICK CARD
►Use the VIAVI P5000i or FiberChek Probe
microscope to inspect both sides of every
connection being used (OCC Port, Launch
Cable, bulkhead connectors, patch cables, etc.)
►Focus fiber on the screen. If dirty, clean the
end-face.
►If it appears clean, run inspection test.
►If it fails, clean the fiber and re-run inspection
test. Repeat until it passes.
Figure 2: Inspect Before You Connect
Figure 1: Equipment Requirements
4100-series Expert OTDR
This quick card explains how to connect to a fiber under test, configure EXPERT OTDR
test settings using Quick Setup, run tests, and analyze results on a VIAVI
ONA-1000 equipped with a 4100-series OTDR module.
► ONA-1000 equipped with the following:
•Fiber Optics Software Release V21.12 or
greater
•4100 Series OTDR Module
•Fiber optic cleaning and inspection tools
►20-meter Fiber optic patch cable (Launch
Cable)
► Optical Coupler to connect Launch Cable to
Fiber Under Test
VIAVI//Public
OneAdvisor-1000 Portable Network Tester
OneAdvisor-1000 Portable Network Tester
QUICK CARD
2
CONNECT TO FIBER UNDER TEST (FUT)
All fibers and connectors should be inspected and
clean prior to connection, as described on page 1.
The OTDR may be connected to the FUT via an
optical patch panel (OPP) or a coupler:
1. Inspect the OTDR port on top of the test set.
2. Inspect the fiber end face of the Launch Cable.
3. Connect the Launch Cable to the OTDR port.
4. If the interface to the FUT is a patch cord,
connect the patch cord to an optical coupler.
5. Inspect the FUT connected to the coupler or
OPP port and the fiber end face of the Launch
Cable.
6. Connect the Launch Cable to the coupler or
OPP port.
Figure 5: Connecting to OPP
LAUNCH TEST
1. Press the Power button on the top of the
OneAdvisor to start the test instrument.
2. Tap the Tests icon
3. Select the OTDR Module
4. Tap the OTDR EXPERT icon
Figure 6: Fiber Optics Home Screen
Figure 4: Connecting to coupler
Figure 3: OTDR Port Inspection
VIAVI//Public
OneAdvisor-1000 Portable Network Tester
OneAdvisor-1000 Portable Network Tester
QUICK CARD
3
CONFIGURE TEST
Figure 7: Setup, Display
1. Tap the Setup soft key .
2. Tap Display and set Distance Unit to your
desired unit of measure.
3. Tap Acquisition and configure the following
basic settings for the trace:
►Laser: Select the wavelength(s) to test.
–Select All or select 1310 nm and
1550 nm to enable bend detection.
►Acquisition Mode:
–Select Manual to manually to enter
Range and Pulse width settings.
–Select Auto to automatically configure
Range, Pulse width, and Resolution
settings.
–Select SmartAcq to perform an
acquisition with a short pulse width,
followed by an acquisition with a longer
pulse width. The first acquisition allows
events at the beginning of the fiber to
be detected more precisely.
►Acq. Time: Select Realtime,Auto or the
desired time to sample the fiber.
►Launch Cable: Select and enter Length
if you are using a Launch Cable.
Enter 20 meters or 66 feet for Viavi
supplied 20-meter launch cables.
4. Tap Alarms and configure pass/fail criteria:
►Set Alarm Level to Fail.
►Set Threshold to Default, or select
alternate alarm thresholds (TIA-568.3,
User, etc.)
Figure 8: Setup, Acquisition
Figure 9: Setup, Alarms
VIAVI//Public
OneAdvisor-1000 Portable Network Tester
OneAdvisor-1000 Portable Network Tester
QUICK CARD
4
Figure 11: SmartLink View, Summary Results
RUN TEST
1. Press the Start soft key to start the test.
After auto-configuration, the OTDR will perform
a connection check to ensure that the
connection is Good. If the Connection is Bad,
disconnect the launch cable, and reconnect as
described on pages 1 and 2, cleaning every fiber
that fails the inspection test.
2. The OTDR will perform an acquisition at the
configured wavelength.
Figure 12: SmartLink View, Event Results
Figure 10: Connection Check
1. Tap the SmartLink tab at the left screen top to
select SmartLink view.
2. Set the toggle switch at the right screen top to
Event Line.
3. View SmartLink results:
►The FUT is displayed as a series of icons
representing events (front connector,
launch cable, connectors, splices, bends,
etc.) and distances. Swipe left or right to
view additional icons on spans with more
than 4 events.
►The center of the display shows summary
results for the entire span for each
acquisition or wavelength. Tap any event
in the upper display to view detailed results
for that specific event.
►Events are marked with a green check or
red xbased on the Alarms setting.
Note: the icon-based view may not be
available on older ONA-1000s when
acquisition Mode = SmartAcq. Rerun the test
with Mode = Auto or contact VIAVI to upgrade
your unit to add this feature.
VIEW SMARTLINK MAP
VIAVI//Public
OneAdvisor-1000 Portable Network Tester
OneAdvisor-1000 Portable Network Tester
QUICK CARD
5
VIEW TRACE
1. Tap the Trace tab at the left screen top to select
Trace view.
2. Set the toggle switch at the screen top to Info.
3. Tap to auto-zoom.
4. View trace results:
►Trace information is shown in the upper
display.
►Graphical results (dB versus distance) are
shown in the center display.
►A color-coded Event table is shown in the
lower display. Swipe up and down to view
all events. Figure 13: Trace view
Figure 14: Table view
1. Tap the Table tab at the left screen top to
select Table view.
2. Set the toggle switch at the right screen top to
the center (off) position.
3. View table results:
►Distance, Loss, and Reflectance are
shown for each event.
►Tap the toggle switch to view All events or
Failed events.
VIEW TABLE
VIAVI//Public
OneAdvisor-1000 Portable Network Tester
OneAdvisor-1000 Portable Network Tester
QUICK CARD
© 2021 VIAVI Solutions, Inc,
Product specifications and descriptions in this
document are subject to change without notice.
Patented as described at viavisolutions.com/patents
Contact Us
To reach the VIAVI office nearest you,
visit viavisolutions.com/contact
+1 844 GO VIAVI
(+1 844 468-4284)
FAST REPORT
1. Tap the File soft key and tap the Project
folder.
2. Tap the Create Directory soft key and
enter a name for your new folder. All trace files
will be saved to this directory.
3. Tap the Exit soft key .
4. Tap the Fast Report soft key and enter
Cable ID, Fiber Number, Locations,
Direction, and Save Mode.
5. Tap Save.
6. Tap to accept the default filename and
save test results.
7. Tap the Fast Report soft key again to return to
the results display.
Figure 15: File Explorer
Figure 16: Fast Report
Other Viavi Test Equipment manuals
Viavi
Viavi RGS-2000NG User manual
Viavi
Viavi T-BERD MTS 5800 Parts list manual
Viavi
Viavi OneAdvisor 1000 User manual
Viavi
Viavi SmartClass Fiber OLTS-85 User manual
Viavi
Viavi 7200 Series Owner's manual
Viavi
Viavi HST-3000 User manual
Viavi
Viavi ComXpert CX100 User manual
Viavi
Viavi 3550 Owner's manual
Viavi
Viavi ALT-9000 User manual
Viavi
Viavi T-BERD/MTS 8000 Parts list manual
Viavi
Viavi 3900 Series User manual
Viavi
Viavi T-BERD/MTS 5800 User manual
Viavi
Viavi T-BERD/MTS-4000 v2 Parts list manual
Viavi
Viavi T-BERD/MTS 8000 User manual
Viavi
Viavi SmartClass FBP-OLP-82 User manual
Viavi
Viavi FIT-82P03-PRO User manual
Viavi
Viavi T-BERD 6000A V2 Parts list manual
Viavi
Viavi T-BERD MTS 5800 Parts list manual
Viavi
Viavi T-BERD MTS 5800 Parts list manual
Viavi
Viavi OneExpert DSL User manual
