Vetek FCS Series User manual

Manual

FCS

NORmal USE

Buttons

ON/OFF

HOLD

UNIT

Starts and turns off scale

hold-funktion holds the value up to 2 minutes.

Switches between units kg and b.

ZERO/TARE Zeroes the scale during range 0 – 30,00 / 60,00 / 150.0 kg.

Indicators

auto power off (Scale turns of if the value is stable for 2 min and no buttons is pressed).

Scale is delivered with Auto power off activated. To deactivte it press and hold the HOLD

button , press ON and the scale should show A_ON. Press ZERO to change to A_OFF. Press OFF

and ON

Size of plate: 330 x 320 mm

Net / Gross Weight: 4,1 / 4,5 kg (Box 44,5x34,6x7 cm or 5 st 46x36x39 cm)

Optimally15-30°C

Working Temp. :

Input:

Output:

Adapter 230 VAC / 9 VDC, 100 mA, +center or 6 AA batteries (Not included).

RS232

TYPECAPACITYDIVITION

FCS 30kg/10g 30 kg 10 g

FCS 60kg/20g 60 kg 20 g

FCS 150kg/50g 150 kg 50 g up to 100 kg, 100 g between 100 och 150 kg

Shipping scale

kg, lb, batterysymbol for low battery, zero (stable zero), a dot to the left side of

the display indicates hold funtion active. Shows EEEEE if scale is overloaded

E-mail:

Info@vetek.com

Website

Adress

Vetek Weighing AB

Hantverksvägen 15

SE- 764 93 VÄDDÖ

Telefon:

+46 (0)176 208 920

Telefax:

+46 (0)176 208 929 www.vetek.com

Manual_FCS_V1

manual

www.vetek.com info@vetek.com 2

SAFETY PRECAUTIONS

All safety messages are identied by the words “WARNING” and “CAUTION”. These words mean

the following: WARNING Important information to alert you to a situation that might cause serious

injury and damage to your property if instructions are not followed.

Use only the correct AC adaptor with the scale. Other adaptors may cause permanent electrical

damage.

CAUTION

• Importantinformationthattellshowtopreventdamagetotheequipment.

• Whenusingthescale,thefollowingsafetyprecautionsshouldalwaysbefollowed.

• Avoidplacingthescaleindirectsunlight,thismaycausediscolorationormalfunction.

• Replaceallbatteriesatthesametime–Donotreplaceonlyaportionofthe6batteriesas

this may cause a malfunction.

• Ifthescaleisnottobeusedforalongperiodoftime,removeallbatteriesfromthebattery

compartment to avoid leakage, which may cause damage to this scale.

• Avoidoverloadingthescale,asthismaycausepermanentdamageandvoidyourwarranty

– do not EVER exceed the maximum capacity of the scale

• Keepthescaleawayfromwater–thisscaleisnotwaterresistant.Shock,injuryand

electrical damage can occur if used in a wet location!

• Matterchargedwithstaticelectricitycouldaectaccuracy.Dischargeallstaticelectricity.

For example, one method is to use Static-Guard spray, and spray it on both sides of the

weighing platform.

manual

Instruktion-FCS Rev 1.2006 Användarinstruktion Utskrift 2006-06-20

Vetek AB Box 79, Industriv. 3 760 40 Väddö Tel 0176 208 920 Fax 0176 208 929

e-mail: [email protected] www. vetek.se Sida 3

PARTS DESCRIPTION

AC adaptor

Socket

ON/OFF key

Turns the scale

power on/off.

Remain on the display for 120 seconds.

UNIT key

Changes weighing units, eg. kg or lb,.

ZERO key (for TARE)

Sets display to zero or

Subtracts weight of a container.

Negative value indicator Weighing unit

Stable indicator

Indicates when the A/D value reading is stable

Low battery indicator

Hold indicator ZERO indicator

Indicates when the reading is stable

HOLD (send data) FUNCTION

Once the hold key is pressed: 1). The CPU will send weight data into RS232 socket. 2)the weight will

remain on the display for 120 seconds after the item has been removed from the scale so the weight can

easily be read.

1) Place the item on the scale platform.

2) Wait for the stable weights to be displayed.

3) Press the hold key. The . hold indicator will turn-on.

4) Remove the item from the scale platform. The items weight reading will remain on the display for

120 seconds.

5) Quit to hold function: Once an item is weighed and the hold function is enabled; you want to quit to

hold function, Press the hold key again to cancel the . hold indicator and return the scale to weight

value.

PART DESCRIPTION

HOLD SEND DATA FUNCTION

Once the hold key is pressed: 1). The CPU will send weight data into RS232 socket. 2)the weight

will remain on the display for 120 seconds after the item has been removed from the scale so the

weight can easily be read.

1) Place the item on the scale platform.

2) Wait for the stable weights to be displayed.

3) Press the hold key. The “.” hold indicator will turn-on.

4) Remove the item from the scale platform. The item’s weight reading will remain on the display

for 120 seconds.

5) Quit to hold function: Once an item is weighed and the hold function is enabled; you want to

quittoholdfunction,Presstheholdkeyagaintocancelthe“.”holdindicatorandreturnthescale

to weight value.

www.vetek.com info@vetek.com

manual

FUNCTION SETTINGS

1. Enter function setting mode.

Press [ON/OFF] to turn the power o, Press [HOLD] rst, then press [ON/OFF], while keeping [HOLD]

pressed, the display will show A_ON or A_OFF.

2. Selection of auto shut o mode.

When the balance enter function setting menu. the display will show A_ON or A_OFF, Press [ZERO]

key, selection display A_ON, this means auto shut o function active. Press [ZERO] again, the

display will show A_OFF, this means auto shut o function inactive.

WEIGHING

Before weighing

Whenever possible, please allow the scale to warm up for several seconds after rst turning the

power on so that the scale will function properly and accurately.

Error messages

EEEE: Overload

Low battery

Weighing procedures

1. Press [ON/OFF] to turn on the scale.

When the power is turned on, all display segments appear for a few seconds and “0” will appear on

the display.

2. Select the weighing unit with [UNIT]. Press [UNIT] to select a weighing unit “kg”, “lb”. Once the

unit has been selected, the selected unit will be displayed next to the weight value.

3. Start weighing If you do not use a container for weighing, Verify the reading is “0”. If not, press

[ZERO/TARE] to display “0”. Place the items to be weighed on the platform. When the reading

becomes stable, the stable weighing is displayed. If you use a container for weighing,

Place an empty container on the platform. Wait for the stability indicator to be displayed and press

[ZERO/TARE]. Place the objects to be weighed in the container. When the reading becomes stable,

the stable weighing displayed.

CALIBRATION

Whentocalibrate-calibrationisalmostneverrequired.

If the scale is inaccurate, calibration may be desired when the scale is rst set up for use, or if the

scale is moved to a dierent altitude or gravitation. This is necessary because the weight of a mass

in one location is not necessarily the same in another location. Also, with time and use, mechanical

deviations can occur.

www.vetek.com info@vetek.com

manual

How to calibrate

**you must have an accurate the full load kilogram weight or combination of weights in order to

calibrate**

1. The scale must be powered OFF. Press and hold [ZERO] rst, then Press [ON/OFF] while keeping

the [ZERO] button depressed, then release both keys. The display will show the A/D value (a series

of random numbers).

2. Wait for the stable indicator to be displayed, Press [UNIT] the display will show “0SAVE”, then the

display will return to the random A/D value.

3. Place the full load kilograms weight(s) on platform. Wait for the stable indicator to display, then

press [UNIT], the display will show “0SAVE”. Calibration is complete, remove the weight(s).

4. Turn the scale OFF (Press the ON/OFF key) , then turn it back ON and check some weight readings.

If calibration is still incorrect, repeat calibration but try it more slowly.

If calibration is repeatedly incorrect then: 1) Replace the batteries, 2) Try a more stable surface or

vibration and interference free location, 3) Be sure there is no static electricity on the scale (use an

anti- static spray to remove static electricity)

FEATURES

 Auto shut o (optional)  Auto calibration

 Auto zero tracking  AC Power (optional)

 Removable display w/3ft cord  kg /lb conversion

 Large LCD (6digits 15 mm high)  hold function

␣Largesquareweighingtray.

SPECIFICATIONS

**SPECIAL WARNING**

Cell-Phones,Cordless-Phones,andanyradio-frequencydevicecancausetemporaryinterference

and cause the scale to temporarily not work properly. Please do not use any electronic device near

the shipping scale. Just like in an Airplane, do not use your cell-phone near the scale when it is in

use. While there is NO risk of permanent damage to the scale, interference can cause an incorrect

calibration or incorrect weight readings.

Model number Capacity Division

FCS-30 30kg 10g

FCS-60 60kg 20g

FCS-100 100kg 20g/50g

FCS-150 150kg 50g/100g

Platter / Tray 330×320mm

Net/gross weight 4.1kg/4.5kg

Package Standard carton: 44.5×34.6×7(cm3)

5 Units in one box: 46×36×39(cm3)

Operating

Temperature

Optimum: 15-30°C

Power source 6×AA Batteries or AC/DC

Adapter 9~12V/100mA (optional)

www.vetek.com info@vetek.com

Table of contents

Popular Scale manuals by other brands

AWS

AWS ZEO-50 user manual

Gima

Gima Glass Body Fat Analyzer Use and maintenance book

Seca

Seca 374 user manual

TEC

TEC TEC SL59 SERIES owner's manual

Axis

Axis B/E Series user manual

Alecto

Alecto ACW-40 user manual

Rice Lake

Rice Lake MSI-4260 IS Technical manual

IKA

IKA RCT basic safety control operating instructions

ADE

ADE M20011 operating manual

Duronic

Duronic KS3000 manual

Digi

Digi SM-720 Service manual

Cardinal

Cardinal CS Series Operation manual

Korona

Korona Kastella Instructions for use

A&D

A&D FC-50Ki instruction manual

BDA

BDA CAMARGUE installation guide

Tanita

Tanita HD-357 Instructions for use

Leifheit

Leifheit 03173 quick start guide

Lumme

Lumme LU-1340 user manual