Verifi P2000 User manual

Veri P2000 User Manual.pdf

Page 2: Manual oriented for on-screen viewing.

Pages 3-4: Manual oriented for double-sided printing.

Rev B - May 2021

INSTALL DRIVER

See included disc or download from verifisafe.com/downloads.

1. Double-click “Verifi P2000 Driver Installer (Windows10 XXbit).msi”

to run the installer.

2. Click “Next” on the “Welcome to the AuthenTec WinBio Fingerprint

Software Installation Wizard” screen.

3. Click “Next” again to install the driver.

4. Click “Finish” when you see the message “AuthenTec WinBio

Fingerprint Software XX-bit has been successfully installed.”

PLUG IN DEVICE

5. Plug the Verifi P2000 Fingerprint Reader into your USB port.

ENROLL FINGERPRINT

6. Press Windows Key + “I” to access Windows Settings.

7. Click “Accounts.”

8. Click “Sign-in options” in the left side colum.

9. Click “Windows Hello Fingerprint” on the right.

10. Click “Set up.”

11. Click “Get started.”

12. Enter your PIN and click “OK”.

13 Follow the on-screen instructions to “Swipe your finger on the

fingerprint sensor.” See “Proper Fingerprint Enrollment” (next page).

14. Press “Close” when you see “All set!”

TEST FINGERPRINT

15. Press Windows Key + “L” to logoff your system.

16. Swipe your finger down across the fingerprint reader to logon.

CONGRATULATIONS! Your fingerprint reader has been installed!

Fingerprint verification performance depends

upon how well you enroll your fingerprint.

When enrolling fingerprints, be sure your finger

remains flat on the fingerprint reader. As you slide

your finger down and across the sensor, maintain

uniform pressure and speed.

How to Setup Your Verifi P2000 Fingerprint Reader Proper Fingerprint Enrollment

Finger Start

Position

Sensor

Finger End

Position

Sensor

Improper Finger Placement

Finger is not flat on surface.

VERIFI by ZVETCO

489 SR 436 #109, Casselberry, FL 32707 USA

REV B - MAY 2021

TROUBLESHOOTING TIPS

• Windows may ask for your PIN after first login with fingerprint.

• The message "Your device is having trouble recognizing you" is almost

always a false positive generated by Windows and not your reader.

• Connect reader directly to your PC, not through a USB hub.

• Keep sensor clean with a little rubbing alcohol and microfiber cloth.

• If your reader becomes unresponsive, adjust Power Management options:

1. Open Windows Device Manager

2. Right-click “AuthenTec Inc. AES2550” under “Biometric Devices”

3. Select "Properties"

4. Open "Power Management" tab (visible to admins only)

5. Uncheck "Allow the computer to turn off this device to save power"

6. Click "OK"

INSTALL DRIVER BEFORE PLUGGING INTO YOUR PC!

This device is not plug and play. Install the driver according to

the enclosed steps before plugging into your computer.

Administrator privileges and Windows PIN are required for install.

P2000

FINGERPRINT READER

by Zvetco

Casselberry, Florida, USA

WINDOWS

How can we help?

We know you’ll love your Verifi P2000 Fingerprint Reader as much

as we do. But we understand not every system is the same, and you

might need additional support to get you up and running. No

problem. We’re here to help!

Our USA-based team has supported thousands of our fingerprint

readers across the globe. Reach out to us today if you need any

help at all. You’ll be glad you did!

 (407) 567-7360

Mon-Fri, 9am-7pm EST

 support@verifisafe.com

365 days a year

 verifisafe.com

24/7

USA SUPPORT

VERIFI by ZVETCO

489 SR 436 #109, Casselberry, FL 32707 USA

REV B - MAY 2021

TROUBLESHOOTING TIPS

• Windows may ask for your PIN after first login with fingerprint.

• The message "Your device is having trouble recognizing you" is almost

always a false positive generated by Windows and not your reader.

• Connect reader directly to your PC, not through a USB hub.

• Keep sensor clean with a little rubbing alcohol and microfiber cloth.

• If your reader becomes unresponsive, adjust Power Management options:

1. Open Windows Device Manager

2. Right-click “AuthenTec Inc. AES2550” under “Biometric Devices”

3. Select "Properties"

4. Open "Power Management" tab (visible to admins only)

5. Uncheck "Allow the computer to turn off this device to save power"

6. Click "OK"

VERIFI by ZVETCO

489 SR 436 #109, Casselberry, FL 32707 USA

REV B - MAY 2021

TROUBLESHOOTING TIPS

• Windows may ask for your PIN after first login with fingerprint.

• The message "Your device is having trouble recognizing you" is almost

always a false positive generated by Windows and not your reader.

• Connect reader directly to your PC, not through a USB hub.

• Keep sensor clean with a little rubbing alcohol and microfiber cloth.

• If your reader becomes unresponsive, adjust Power Management options:

1. Open Windows Device Manager

2. Right-click “AuthenTec Inc. AES2550” under “Biometric Devices”

3. Select "Properties"

4. Open "Power Management" tab (visible to admins only)

5. Uncheck "Allow the computer to turn off this device to save power"

6. Click "OK"

INSTALL DRIVER BEFORE PLUGGING INTO YOUR PC!

This device is not plug and play. Install the driver according to

the enclosed steps before plugging into your computer.

Administrator privileges and Windows PIN are required for install.

P2000

FINGERPRINT READER

by Zvetco

Casselberry, Florida, USA

WINDOWS

INSTALL DRIVER BEFORE PLUGGING INTO YOUR PC!

This device is not plug and play. Install the driver according to

the enclosed steps before plugging into your computer.

Administrator privileges and Windows PIN are required for install.

P2000

FINGERPRINT READER

by Zvetco

Casselberry, Florida, USA

WINDOWS

How can we help?

We know you’ll love your Verifi P2000 Fingerprint Reader as much

as we do. But we understand not every system is the same, and you

might need additional support to get you up and running. No

problem. We’re here to help!

Our USA-based team has supported thousands of our fingerprint

readers across the globe. Reach out to us today if you need any

help at all. You’ll be glad you did!

 (407) 567-7360

Mon-Fri, 9am-7pm EST

 support@verifisafe.com

365 days a year

 verifisafe.com

24/7

USA SUPPORT

How can we help?

We know you’ll love your Verifi P2000 Fingerprint Reader as much

as we do. But we understand not every system is the same, and you

might need additional support to get you up and running. No

problem. We’re here to help!

Our USA-based team has supported thousands of our fingerprint

readers across the globe. Reach out to us today if you need any

help at all. You’ll be glad you did!

 (407) 567-7360

Mon-Fri, 9am-7pm EST

 support@verifisafe.com

365 days a year

 verifisafe.com

24/7

USA SUPPORT

INSTALL DRIVER

See included disc or download from verifisafe.com/downloads.

1. Double-click “Verifi P2000 Driver Installer (Windows10 XXbit).msi”

to run the installer.

2. Click “Next” on the “Welcome to the AuthenTec WinBio Fingerprint

Software Installation Wizard” screen.

3. Click “Next” again to install the driver.

4. Click “Finish” when you see the message “AuthenTec WinBio

Fingerprint Software XX-bit has been successfully installed.”

PLUG IN DEVICE

5. Plug the Verifi P2000 Fingerprint Reader into your USB port.

ENROLL FINGERPRINT

6. Press Windows Key + “I” to access Windows Settings.

7. Click “Accounts.”

8. Click “Sign-in options” in the left side colum.

9. Click “Windows Hello Fingerprint” on the right.

10. Click “Set up.”

11. Click “Get started.”

12. Enter your PIN and click “OK”.

13 Follow the on-screen instructions to “Swipe your finger on the

fingerprint sensor.” See “Proper Fingerprint Enrollment” (next page).

14. Press “Close” when you see “All set!”

TEST FINGERPRINT

15. Press Windows Key + “L” to logoff your system.

16. Swipe your finger down across the fingerprint reader to logon.

CONGRATULATIONS! Your fingerprint reader has been installed!

Fingerprint verification performance depends

upon how well you enroll your fingerprint.

When enrolling fingerprints, be sure your finger

remains flat on the fingerprint reader. As you slide

your finger down and across the sensor, maintain

uniform pressure and speed.

How to Setup Your Verifi P2000 Fingerprint Reader Proper Fingerprint Enrollment

Finger Start

Position

Sensor

Finger End

Position

Sensor

Improper Finger Placement

Finger is not flat on surface.

INSTALL DRIVER

See included disc or download from verifisafe.com/downloads.

1. Double-click “Verifi P2000 Driver Installer (Windows10 XXbit).msi”

to run the installer.

2. Click “Next” on the “Welcome to the AuthenTec WinBio Fingerprint

Software Installation Wizard” screen.

3. Click “Next” again to install the driver.

4. Click “Finish” when you see the message “AuthenTec WinBio

Fingerprint Software XX-bit has been successfully installed.”

PLUG IN DEVICE

5. Plug the Verifi P2000 Fingerprint Reader into your USB port.

ENROLL FINGERPRINT

6. Press Windows Key + “I” to access Windows Settings.

7. Click “Accounts.”

8. Click “Sign-in options” in the left side colum.

9. Click “Windows Hello Fingerprint” on the right.

10. Click “Set up.”

11. Click “Get started.”

12. Enter your PIN and click “OK”.

13 Follow the on-screen instructions to “Swipe your finger on the

fingerprint sensor.” See “Proper Fingerprint Enrollment” (next page).

14. Press “Close” when you see “All set!”

TEST FINGERPRINT

15. Press Windows Key + “L” to logoff your system.

16. Swipe your finger down across the fingerprint reader to logon.

CONGRATULATIONS! Your fingerprint reader has been installed!

Fingerprint verification performance depends

upon how well you enroll your fingerprint.

When enrolling fingerprints, be sure your finger

remains flat on the fingerprint reader. As you slide

your finger down and across the sensor, maintain

uniform pressure and speed.

How to Setup Your Verifi P2000 Fingerprint Reader Proper Fingerprint Enrollment

Finger Start

Position

Sensor

Finger End

Position

Sensor

Improper Finger Placement

Finger is not flat on surface.

Other Verifi Accessories manuals

Verifi

Verifi VM0214 User manual

Popular Accessories manuals by other brands

Hillco

Hillco 2810 Operator's manual

Siemens

Siemens QSA2700D Basic documentation

Contours

Contours ZY024 manual

Saivod

Saivod VS621 manual

Virtuox

Virtuox VirtuCLEAN 2.0 user manual

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS user manual

Z-Wave

Z-Wave HSD-200Z user manual

turck

turck FMX-IM-2UPLI63FX quick start guide

Decagon Devices

Decagon Devices 10HS manual

UPPAbaby

UPPAbaby Cup Holder user manual

Elko

Elko SmartSensor Leakage Wireless manual

Grizzly

Grizzly H8371 instructions

Panasonic

Panasonic HG-T Series user manual

IFM Electronic

IFM Electronic Efector 250 Series Brief instructions

DigiDesign

DigiDesign 888/24 I/O installation guide

PROZIS

PROZIS QUAY user manual

patagonia

patagonia PSI Vest user manual

SFC Energy

SFC Energy EFOY GO! manual