Vents Simple 100 User manual

AXIAL FAN

USER’S MANUAL

www.ventilation-system.com

VENTS 100 Simple

CONTENTS

Delivery set............................................................................................................................................................................................................................................. 6

Brief description .................................................................................................................................................................................................................................. 6

Operation guidelines ....................................................................................................................................................................................................................... 6

Designation key................................................................................................................................................................................................................................... 7

Installation and setup ...................................................................................................................................................................................................................... 7

Fan setup ........................................................................................................................................................................................................................................... 8

Electronics operation algorithm .............................................................................................................................................................................................. 10

Technical maintenance................................................................................................................................................................................................................... 11

Storage and transportation regulations............................................................................................................................................................................... 11

Manufacturer’s warranty................................................................................................................................................................................................................ 12

This user’s manual is a main operating document, intended for technical, maintenance, and operating staﬀ.

The manual contains information about the purpose, technical details, operating principle, design, and installation of the

VENTS 100 Simple unit and all of its modiﬁcations.

Technical and maintenance staﬀ must have theoretical and practical training in the ﬁeld of ventilation systems and should

be able to work in accordance with workplace safety rules as well as construction norms and standards applicable in the

territory of the country.

The information in this user’s manual was correct at the time of the document’s preparation.

The Company reserves the right to modify the technical characteristics, design, or conﬁguration of its products at any time

in order to incorporate the latest technological developments.

No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means in any

information search system or translated into any language in any form without the prior written permission of the Company.

READ THE USER’S MANUAL CAREFULLY BEFORE PROCEEDING WITH INSTALLATION WORKS.

COMPLIANCE WITH THE MANUAL REQUIREMENTS ENSURES RELIABLE OPERATION AND LONG

SERVICE LIFE OF THE UNIT.

KEEP THE USER’S MANUAL AVAILABLE AS LONG AS YOU USE THE UNIT. YOU MAY NEED TO RE-READ

THE INFORMATION ON THE PRODUCT SERVICING.

FOLLOW THE USER’S MANUAL REQUIREMENTS TO ENSURE DURABLE AND

TROUBLE-FREE OPERATION OF THE UNIT.

Disconnect the unit from power supply prior to any connection, servicing, maintenance, and repair operations.

Only qualied electricians with a work permit for electrical units up to 1000 V are allowed

for installation and maintenance. The present user’s manual should be carefully read

before beginning works.

• Single-phase power mains must comply with the acting local electrical norms and standards.

• Fixed electrical wiring must be equipped with an automatic circuit breaker.

• The unit must be connected to power mains through a QF automatic circuit breaker integrated into the ﬁxed wiring

system. The gap between the circuit breaker contacts on all poles must be not less than 3 mm. Check the unit for any

visible damages of the impeller and the casing before starting installation. The casing internals must be free of any foreign

objects that can damage the impeller blades.

• While mounting the unit, avoid compression of the casing! Deformation of the casing may result in the motor jam and

noisy operation. Misuse of the unit and any unauthorised modiﬁcations are not allowed.

• Take steps to prevent ingress of smoke, carbon monoxide, and other combustion products into the room through open

chimney ﬂues or other ﬁre-protection devices. Suﬃcient air supply must be provided for proper combustion and exhaust

of gases through the chimney of fuel burning equipment to prevent back drafting. Transported air must not contain any

dust or other solid impurities, sticky substances, or ﬁbrous materials.

• Do not use the unit in a hazardous or explosive environment containing spirits, gasoline, insecticides, etc.

• Do not close or block the intake or exhaust vents in order to ensure eﬃcient air ﬂow.

• Do not sit on the unit and do not put objects on it.

• The unit is allowed to be used by children aged from 8 years old and above and persons with reduced physical, sensory,

or mental capabilities or no experience and knowledge provided that they have been given supervision or instruction

THE PRODUCT MUST BE DISPOSED SEPARATELY AT THE END OF ITS SERVICE LIFE.

DO NOT DISPOSE THE UNIT AS UNSORTED MUNICIPAL WASTE.

regarding safe use of the unit and understand the risks involved.

• Do not allow children to play with the unit.

DELIVERY SET

Fan — 1 pc.

Screws and dowels — 4 pcs.

Plastic screwdriver (only for the models with a timer) — 1 pc.

User’s manual — 1 pc.

Packing box — 1 pc.

BRIEF DESCRIPTION

The unit described herein is an axial fan for exhaust ventilation of small to medium-sized premises heated during winter.

The fan is made of white plastic. The fan design can also include a backdraft damper to prevent back ﬂow when the fan is

switched oﬀ. The fan ﬁts 100 mm air ducts.

OPERATION GUIDELINES

The fan is rated for connection to single-phase AC 230 V/50 Hz or 230 V/60 Hz power mains. Air motion direction in the

system must match the pointer on the fan casing.

Ingress protection rating against access to hazardous parts and water ingress is IP45.

The fan is rated for operation at the ambient temperature ranging from +1 °C up to +45 °C.

The unit is rated as a Class II electrical appliance.

DESIGNATION KEY

Vents 100 Simple X Х X

Motor and impeller modications:

L — motor on ball bearings

Turbo — high-powered motor

12 — motor with 12 V/50 Hz rated voltage

K — backdraft damper

Additional options:

V — built-in pull-cord switch

T — turn-oﬀ delay timer

T1 — turn-on and turn-oﬀ delay timer

TH — humidity sensor and turn-oﬀ delay timer

Fan series

Outlet duct diameter [mm]

INSTALLATION AND SETUP

The fan is designed for wall or ceiling mounting with direct air exhaust to the ventilation shaft or into the round air duct of

matching diameter (Fig. 2).

Fan installation sequence:

Step 1. Cut oﬀ power supply and make sure electricity has been turned oﬀ (Fig. 4).

Step 2. Run the power cable to the vent hole (Fig. 5).

Step 3. Remove the front panel from the fan. Then remove the terminal block cover (Fig. 6).

Step 4. Mark and drill holes for mounting the fan and then install the fan (Fig. 7-9).

Step 5. Connect the fan to power mains according to the wiring diagram (Fig. 13-16).

Step 6. Install the terminal block cover (Fig. 10) and the front panel on the fan casing (Fig. 11).

Step 7. Supply power voltage to the fan (Fig. 12).

FAN SETUP

on — interval timer turning on and adjustment is performed with the potentiometer Ton. To turn the interval timer oﬀ

set the potentiometer Ton into the leftmost position. Rotation of the potentiometer for 1/3 clockwise sets the interval timer

operation for 6 hours, rotation of the potentiometer for 2/3 clockwise sets the interval timer operation for 12 hours, and

rotation of the potentiometer clockwise in the rightmost position sets the interval timer operation for 24 hours.

oﬀ — To adjust the fan turn-oﬀ delay time, turn the control knob To clockwise to increase and counter-clockwise to

decrease the turn-oﬀ delay time respectively, adjustable from 2 up to 30 minutes.

— To adjust the humidity set point turn the control knob H clockwise to increase and counter-clockwise to decrease the

humidity sensor set point, adjustable from 60 % up to 90 %.

WARNING! If the switch is turned o or the indoor humidity falls below the set point within 60 seconds after

activation of the switch or the humidity sensor, the fan continues operation at low speed.

Terminal designations on wiring diagrams:

L — phase

N — 0

S — external switch

QF — automatic circuit breaker

CAUTION! The fans rated for 12 V power voltage (stated on the packing box and on the fan casing) connect to

12 V power mains only!

DO NOT USE A METAL SCREWDRIVER, KNIFE, ETC. FOR ADJUSTMENT

OPERATIONS NOT TO DAMAGE THE CIRCUIT BOARD.

60% 90%

Toﬀ

2 min 30 min

Ton

Oﬀ 24 hour

The fan delivery set includes a specially designed plastic

screwdriver for fan settings adjustments. Use it to change

the turn-on and turn-oﬀ delay time and the humidity set

point.

ELECTRONICS OPERATION ALGORITHM

The fan with the timerT — the fan is started after actuation of the external switch, e.g. the light switch. The control voltage

is supplied to the input terminal LT (ST). After the control voltage is oﬀ the fan continues to operate within the set time

period adjustable from 2 to 30 minutes by the timer.

The VT model is turned on and oﬀ by the pull-cord switch.

The fan with the timer T1 — after turning on the switch, for example, a light switch, the fan is switched on in a set turn-on

delay time period, adjustable from 0 to 2 minutes. After the switch is turned oﬀ the fan keeps operating for a set turn-oﬀ

delay time period, adjustable from 2 to 30 minutes.

The fan with the timer and the humidity sensor TH — the fan starts after the control voltage is supplied to the input

terminal S or if indoor humidity level Hexceeds the set point adjustable from ~60 % to ~90 %. After the control voltage is oﬀ

or the humidity level has decreased the fan will keep running within the time set by the timer ranging from 2 to 30 minutes.

To set the maximum humidity setpoint 90 % set the potentiometer to H max position.

To adjust the fan turn-on delay time, turn the control knob T clockwise to increase and counter-clockwise to decrease the

turn-on delay time respectively. To adjust the humidity set point turn the control knob Hclockwise to increase and counter-

clockwise to decrease the humidity sensor set point.

CAUTION!The timer circuit is live! Disconnect the fan from power mains prior to any adjustment operations. The

fan delivery set includes a specially designed plastic screwdriver for fan settings adjustments. Use it to change

the turn-on and turn-o delay time and the humidity set point.

DO NOT USE A METAL SCREWDRIVER, KNIFE, ETC. FOR ADJUSTMENT

OPERATIONS NOT TO DAMAGE THE CIRCUIT BOARD.

Table of contents

Other Vents Fan manuals

Vents

Vents VKMz 125 User manual

Vents

Vents D User manual

Vents

Vents VK Series User manual

Vents

Vents VK EC Series User manual

Vents

Vents TwinFresh Style Wi-Fi User manual

Vents

Vents VUT 180 P5 User manual

Vents

Vents VOX-M User manual

Vents

Vents D Series User manual

Vents

Vents VKV EC User manual

Vents

Vents TwinFresh Expert User manual

Vents

Vents TT PRO Series User manual

Vents

Vents VUT 300 WH EC Mounting instructions

Vents

Vents VKM 100 E User manual

Vents

Vents TwinFresh Expert RW1-50 V.2 User manual

Vents

Vents FB-K2 Series User manual

Vents

Vents Frigate HRV 120 SR User manual

Vents

Vents TwinFresh Comfo RA-50 User manual

Vents

Vents TT Silent-M 100 User manual

Vents

Vents VUE P3B EC A14 User manual

Vents

Vents TT PRO EC User manual

Vents

Vents TwinFresh Atmo Wi-Fi User manual

Vents

Vents Quiet-Mild Series User manual

Vents

Vents M1 Series User manual

Vents

Vents KSB315R1 User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual