Vents iFan Celsius User manual
AXIAL INTELLIGENT FAN
user's manual
model
iFan Celsius
Approval mark
Manufactured on (date)
Sold
(name and stamp of the trade company)
Date of sale
ACCEPTANCE CERTIFICATE
The fan is duly recognized
as serviceable.
F01EN-(iFan Celsius)-03
2
Disconnect the fan from power mains prior to any connection, servicing and repair operations.
Mounting and maintenance are allowed for duly qualified electricians with valid electrical work permit for electric operations
at the units up to 1000 V after careful study of the present user's manual.
The single-phase power mains must comply with the acting local electrical norms and standards.
The fixed electrical wiring must be equipped with an automatic circuit breaker.
The fan must be connected to power mains through an automatic circuit breaker QF integrated into the fixed wiring system
with the gap between the breaker contacts on all poles not less than 3 mm.
Check the fan for any visible damages of the impeller and the casing before starting installation.
The casing internals must be free of any foreign objects which can damage the impeller blades.
Misuse of the device or any unauthorized modification is not allowed.
The fan is not to be used by children and persons with reduced physical, mental or sensory capacities, without proper practical
experience or expertise, unless they are controlled or instructed on the product operation by the person(s) responsible
for their safety.
Do not leave children unattended and do not let them play with the product.
Take steps to prevent ingress of smoke, carbon monoxide and other combustion products into the room through open chimney
flues or other fire-protection devices.
Sufficient air supply must be provided for proper combustion and exhaust of gases through the chimney of fuel burning
equipment to prevent back drafting.
Transporting medium must not contain any dust or other solid impurities, sticky substances or fibrous materials.
Do not use the fan in the environment containing hazardous or explosive materials and vapours, i.e. spirits, gasoline,
insecticides, etc.
Do not close or block the fan intake or extract vents in order to ensure the most effective air passage.
Do not sit on the fan and do not put objects on the fan.
Fulfill the requirements stated in this user's manual to ensure long service life of the product.
WARNING
!
WARNING! Read the present user's manual carefully before proceeding with installation works.
Compliance with the manual requirements ensures reliable operation and long service life of the product.
Keep the user's manual available as long as you use the product.
You may need to re-read the information on the product servicing.
DELIVERY SET
The delivery set includes:
1. Fan - 1 pce;
2. Logo - 1 pce;
3. Remote controller - 1 pce;
4. Spigot Ø 100 mm - 1 pce;
5. Spigot Ø 125 mm - 1 pce;
6. Screws and dowels - 4 pcs;
7. User's manual - 1 pce.
DESCRIPTION
Due to constant improvements the design of some models may slightly differ from those ones described in this manual.
The product described herein is the axial fan made of high-quality plastic designed for extract ventilation of small and
medium-sized residential premises that are heated during winter period.
Table 1
Voltage [V]
Frequency [Hz]
Max. power [W]
Current [A]
-1
RPM [min ]
3
Max. air capacity [m /h]
Ingress Protection
Weight [kg]
100-240
50-60
3,8
0,03
2200
133
IP 44
0,35 3
WARNING
!
Recycle at the end of the service life.
Do not dispose the product with unsorted municipal trash.
Table 2
Overall dimensions
The fan has four ventilation modes:
1. Standby mode - standard operation mode for the fan in case of no signalling from the sensors or external switch.
In standby mode the fan does not run.
2. 24 Hours - the fan runs at low speed for minimum round-the-clock ventilation. As temperature set point is crossed, the fan
switches to MAX mode (by default) or to SILENT mode. The fan switches to SILENT mode when the external switch is closed.
3. SILENT - silent operation mode of the fan. This mode is may be activated by the external switch or after corssing the
temperature set point. For temperature sensor, this mode may be activated from the fan.
4. MAX - temperature-activated operation mode. It is switched on as temperature set point is crossed.
This mode is activated for the temperature sensor by default.
4
Speed
Spigot
dia.
Noise level at
3 m [dBA]
Max. air
3
capacity [m /h]
100
24 Hours 33 17
152
206
29 28
100/125
Silent 72 22
Max 106 31
125
24 Hours 40 17
Silent 83 21
Max 133 32
Air capacity,
3
factory settings [m /h]
33
72
82
40
83
97
Air capacity
3
control range [m /h]
-
33 ... 72
72 ... 106
-
40 ... 83
83 ... 133
PRODUCT MOUNTING
The fan is designed for mounting into round
Ø 100 or 125 mm air duct or installation into
the ventilation shaft.
The replaceable adapter of required size may be used
to facilitate mounting.
The fan is equipped with a removable grille.
Press the latches slightly to release the grille from the
front cover.
While installing the grille on the front cover back
match the latches and respective slots in the cover
and insert to click.
The pointer on the reverse side of the grille must be
directed to the shorter side close to the hole.
100
125
5
QF
The fan casing has three round lowered tabs for cable entry.
Cut out a hole at the most suitable place with a knife.
FAN MOUNTING SEQUENCE
6
4 5 6
1 2 3
7
7 8 9
10 11 12
8
The fan may be connected to power mains by four wiring diagrams. The fan is compatible with 100-240 V / 50-60 Hz
power mains.
Wiring diagram 1
L and N terminals are connected to live and neutral respectively. The fan is always in standby mode and does not run.
As 24 HOURS Mode is activated the fan runs permanently at low speed to ensure minimum round-the-clock ventilation.
After crossing the temperature set point the fan switches to MAX (by default) or SILENT mode.
After the indoor temperature falls 2 °C below the set point, the fan reverts to the previous mode.
N
L
LT
L
N
Standby mode
(fan does not run)
or
24 Hours mode
3
(fan operated at 40/33 m /h)
Temperature
rises
MAX (SILENT)
mode is activated
Temperature falls 2 °C below
the set temperature point
9
Wiring diagram 2
L and N terminals are connected to live and neutral respectively and L and LT terminals are joined by the jumper.
The fan is always in SILENT mode. 24 HOURS mode may not be activated.If the temperature rises above the set point,
the fan is switched to MAX (by default) or SILENT (if set) mode. After the indoor temperature falls 2 °C below the set
temperature point, the fan reverts to the previous mode.
Fan operates with air
3
flow 83/72 m /h (MAX)
40/33 m3/h (SILENT)
Temperature
rises
MAX (SILENT)
mode is activated
Temperature falls 2 °C below
the set temperature point
LT
L
N
N
L
10
Wiring diagram 3
L and N terminals are connected to live and neutral respectively. LT contact is connected to live through external switch,
light switch. The fan is always in standby mode. As 24 HOURS Mode is activated the fan runs permanently at low speed to
ensure minimum round-the-clock ventilation. As the external switch is closed the fan switches to SILENT mode. In some time
after the external switch is closed the fan reverts to the previous mode. If the temperature rises above the set point, the fan is
switched to MAX (by default) or SILENT (if set) mode. After the indoor temperature falls 2 °C below the set temperature point,
the fan reverts to the previous mode.
LT
L
N
S
N
L
Standby mode
(fan does not run)
or
24 Hours mode
3
(Fan operates at 40-33 m /h)
Fan operation in
Silent mode
Turn-off delay timer
starts (5-15-30 min)
Switch is
closed
Switch is off
Turn-on delay timer
starts (0-2-5 min) Switch is off
Temperature
rises
MAX (SILENT)
mode is activated
Temperature falls 2 °C below
the set temperature point
Table of contents
Other Vents Fan manuals
Vents
Vents 100 Style Eco User manual
Vents
Vents VKMI Series Mounting instructions
Vents
Vents VUT 300 E2V EC User manual
Vents
Vents CBF 110 DC TH User manual
Vents
Vents TT PRO EC User manual
Vents
Vents Solo RA1-35A-9 P User manual
Vents
Vents VCUN User manual
Vents
Vents Solo RA1-35A-9 P User manual
Vents
Vents VKM EC User manual
Vents
Vents FB-K2 Series User manual
Vents
Vents P2-1-300 Owner's manual
Vents
Vents TT User manual
Vents
Vents TwinFresh Atmo Wi-Fi User manual
Vents
Vents VCU(z) Series User manual
Vents
Vents VUT 180 P5 User manual
Vents
Vents Lumis 100 User manual
Vents
Vents TwinFresh Expert User manual
Vents
Vents TwinFresh Comfo RA1-25 User manual
Vents
Vents VPA 100 Series User manual
Vents
Vents VK Series User manual
Popular Fan manuals by other brands
ELTA FANS
ELTA FANS H03VV-F installation guide
Hunter
Hunter 20714 Owner's guide and installation manual
Emerson
Emerson CARRERA VERANDA CF542ORB00 owner's manual
Hunter
Hunter Caraway Owner's guide and installation manual
Panasonic
Panasonic FV-15NLFS1 Service manual
Kompernass
Kompernass KH 1150 operating instructions
