VentAHood EUROLINE Operating instructions

Page 1

(Rev. 02/08)

L113

CUS

Read and Save These Instructions

All Hoods Must Be Installed By A Qualified Installer

INSTALLATION INSTRUCTIONS

EUROLINE/EUROLINE PRO

ISLAND RANGE HOOD

Read All Instructions Thoroughly Before Beginning Installation

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,

OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

A. Installation work and electrical wiring must be done by qualified

person(s) in accordance with all applicable codes and standards,

including fire-rated construction. Switch power off at service panel

and lock the service disconnecting means to prevent power from

being switched on accidentally during installation.

B. When cutting or drilling into wall or ceiling, do not damage

electrical wiring and other hidden utilities.

C. Ducted fans must always be vented to the outdoors.

D. Sufficient air is needed for proper combustion and exhausting of

gases through the flue (chimney) of fuel burning equipment to

prevent back drafting. Follow the heating equipment

manufacturer’s guideline and safety standards such as those

published by the National Fire Protection Association (NFPA), and

the American Society for Heating, Refrigeration and Air

Conditioning Engineers (ASHRAE), and local code authorities.

WARNING - TO REDUCE THE RISK OF FIRE, USE ONLY METAL

DUCTWORK

Page 2

(Rev. 02/08)

L113

Ducting Do’s and Don’ts

NEVER restrict the duct size. The island dual blower unit (T200) requires 8” round duct or

equivalent (50 square inches). The island cluster blower unit (T400) requires 12” round or

equivalent (113 square inches). Using the included Vent-A-Hood transition will ensure proper

efficiency.

Do not use flexible or corrugated duct. This type of duct will restrict airflow and reduce

performance. Only use smooth, galvanized, metal duct. Observe local codes regarding special

duct requirements and placement of duct against combustibles. Make the duct run as short and

as straight as possible with as few turns as possible. Avoid sharp-angled turns. Instead, use

smooth, gradual turns such as adjustable elbows or 45 degree angled turns. For duct runs over

20 feet, increase the duct diameter by one inch for every ten feet of duct. A 90 degree elbow is

equal to 5 feet of duct. Using Vent-A-Hood roof jacks or wall louvers (back page) will ensure

proper efficiency. Airflow must not be restricted at the end of the duct run. Do not use screen

wire or spring-loaded doors on wall louvers or roof jacks. Do not terminate venting into an attic

or chimney. Where possible, seal joints with duct tape. The hood must be ducted to the outdoors

without restrictions.

Blower Duct Size Sq. Inch Area Vent-A-Hood Transition

Island Dual (T200) 8” round or equivalent 50” VP565 (Included)

Island Cluster Blower (T400) 12” round or equivalent 113” VP564 (Included)

YES

Smooth Duct Smooth Gradual Turn

Flexible Duct Sharp Angled Turns

Page 3

(Rev. 02/08)

L113

36”

8’ Ceiling

30”

18”

Optional

Duct Cover

Installation Details

1) Read all instructions thoroughly before beginning installation. Note: These instructions apply to standard hoods only.

Custom hoods may require additional specification consideration.

2) When installing an island range hood, it is recommended that the bottom edge of the hood be located no more than 30”

above the cooking surface. Exceeding recommended mounting height may compromise performance.

3) Load-bearing framework in the ceiling is necessary for the installation of an island hood. Additional framework

construction may be required. Do not attach an island hood to a structure that cannot support twice the weight of the

hood.

If applicable, remove the duct cover from its packaging and remove the hood-mounting screws from the base of the

duct cover. Install the duct cover to the load-bearing framework in the ceiling using appropriate hardware through the

four inside corner mounting flanges on the top of the duct cover.

4) Install the duct from the outside of the home down to the location of the exhaust outlet on the top of the transition plus

1”. This will allow the transition to engage 1” inside of the duct. Consult the connection diagrams (on next page) for

further details on exhaust outlet placement.

Use duct tape to seal all joints. A complete listing of available Vent-A-Hood ducting materials is listed on the back page

of this instruction sheet.

Transition heights are as follows:

Island Dual Blower (T200): 8” round duct connects to 9” tall VP565 transition (included).

Island Cluster Blower (T400): 12” round duct connects to 11 1/4” tall VP564 transition (included).

5) Prepare a protective surface on the floor or countertop for the hood. Remove the hood from its packaging and place it

upside-down on the protective surface for access to the inside of the hood.

Shown with duct cover installed (sold separately).

Page 4

(Rev. 02/08)

L113

Centerline

Of Hood

5" x 16"

Exhaust

Opening

8" Transition

Opening

Centerline

Of Hood

Vent Holes

Electrical 7 ¾"

12" Transition

Opening 2 ¼”

Above Top of

Hood

8” Blower

Outlets Centerline

of Hood

Centerline

of Hood

Vent Holes

Electrical (2)

7 ¾”

10 ½”

16"5"

8" Round 8" Round

2 ¼”

18”

18"

12" Round 12" Round

11 ¼"

8" Round 8" Round 8" Round

Model Volts Amps RPM CFM

[email protected]” Equivalent CFM CFM

[email protected]”

CFM

[email protected]”

CFM

[email protected]”

Minimum Round

Duct Size

Square

Inches

T200 Island Dual

T400 Island Cluster

115

3.4

6.8

1550

600

1200

900

1800

572

1144

540

1080

480

960

8” (or equivalent)

12” (or equivalent)

113

Note: Add 0.5 amp for each halogen light.

Because the Magic Lung uses centrifugal filtration rather than conventional baffle or mesh filters, the Magic Lung blower can handle cooking equipment with higher cubic feet per minute (CFM) requirements and can deliver equivalent CFM much more efficiently

than other than other filtration systems. When comparing the Magic Lung with other blower units made by other manufacturers, use the “Equivalent CFM”.

Installation Details Continued

6) Remove the blower shields (A) by loosening the two brass screws on the bottom of the shield. Gently close the back

draft dampers from the top side of the hood. To remove the blower housings, unsnap the suitcase latches (B) (one on

each side of the housing). The housings should be pulled forward and gently “tipped” to clear the blower wheels and

then out of the hood.

Warning: Make sure power is off and locked at the service disconnecting

means on the service panel during installation.

Connection Diagram (48”- 66” Widths)

Connection Diagram (36”- 48” Widths)

600 CFM T200 Dual Blower

(Top View)

1200 CFM T400 Dual Blowers

(Top View)

7) Remove the blower deck assembly by removing the 12 screws around the blower mounting plate. Unplug the electrical

connector(s) and set the blower assembly aside, taking care not to damage the blower wheels.

8) Install an appropriate 1/2” UL listed electrical wire clamp through the electrical strap(s) on top of the hood deck. Install

electrical wiring from the service panel to the hood location for each blower assembly. Consult the connection diagrams

(above) for further details on electrical placement. Support the hood beneath the location where it will hang and feed

the electrical wire(s) into the wire clamp(s). Tighten the wire clamp(s).

Transition Installed

(Side View)

VP565 Standard Transition

(Included)

VP564 Standard Transition

(Included)

Transition Installed

(Side View)

Page 5

(Rev. 02/08)

L113

Installation Details Continued

9) Raise the hood to its final position and attach it to the load-bearing framework in the ceiling using appropriate hardware

or to the duct cover using the screws previously removed in Step 3.

10) From inside the hood, using UL listed wire nuts, attach the “neutral” wire(s) to the white lead(s), the “hot”

wire(s) to the black lead(s), and the ground wire(s) to the green lead(s).

Warning: Do not operate hood without proper ground connection.

11) Attach the transition to the blower deck assembly and seal with duct tape. The transition must fit inside the exhaust

collar on the blower deck assembly. Reconnect the electrical connector(s). For assemblies with two connectors, connect

the right harness to the front connector and the left harness to the back connector. While taking care to properly align

the duct connection between the transition and the duct in the ceiling, reinstall the blower deck assembly into the

hood using the 12 screws previously removed in Step 7.

12) Replace the blower housings and the blower shields. Make sure that the dampers open and close smoothly.

13) Refer to Owner Maintenance Guide Operating Instructions for proper hood operation. Test all blower and light functions

to ensure they are operating properly.

VENTINGVENTING

VENTING AA

ACCESSORIESCCESSORIES

CCESSORIESCCESSORIES

CCESSORIES

Page 6L113 Rev. 02/08

6” RECTANGULAR DUCT PIPE

MODEL DIM

VP507 6” x 8 ½”

24”

8 ½”

6”

ROUND DUCT PIPE

MODEL DIM

VP500

VP501

VP502

6” Round

7” Round

8” Round

36”

6”

7”

8”

3 ¼” RECTANGULAR DUCT PIPE

MODEL DIM

VP504

VP505

VP506

3 ¼” x 10”

3 ¼” x 12”

3 ¼” x 16”

30”

10”

12”

16”

3 ¼”

OFFSET L & R TRANSITION

FOR ISLAND BLOWERS

MODEL DIM

VP542

VP543

Top Left

Top Right

8”

12”

5”

16”

SIDE VENT TRANSITION L & R

FOR ISLAND BLOWERS

MODEL DIM

VP544

VP545

Left Side

Right Side

19”

8”

16” 5”

6” x 8 ½” COLLAR

MODEL DIM

VP537 6” x 8 ½”

11 ½”

6” x 8 ½”

Opening

9”

OFFSET KIT - RECTANGULAR

MODEL DIM

VP550 6” Rnd to 3 ¼”x 10”

16”

11”

6”

11”

3 ¼” 10”

STANDARD ISLAND TRANSITION

MODEL DIM

VP565 5” x 16” to 8”

8”

9”

16” 5”

CLUSTER BLOWER TRANSITION

MODEL DIM

VP564 8” & 8” to 12”

18 ½”

12”

11 ¼”

“Y”TRANSITION

MODEL DIM

VP517

VP518

VP551

8” & 8” to 12”

6” & 8” to 12”

6” & 8” to 10”

18”

10”

12”

3 ¼” x 10” BACK VENT ELBOW

MODEL DIM

VP559 3 ¼” x 10”

4 ¼” 10”

14”

3 ¼”

MULTI-BLOWER TRANSITION

MODEL DIM

VP562

VP563

6” & 8” to 10”

8” & 8” to 12”

VP562 - 17 ½”

VP563 - 16 ½”

10”

12”

VP562 - 23 ¼”

VP563 - 30 ½”

3 ¼” x 10”TO 7”TRANSITION

MODEL DIM

VP521 3 ¼” x 10” to 7”

7”

7 ½”

3 ¼”

10”

LOW PROFILE ROOF JACK

(MAXIMUM 4/12 PITCH)

MODEL DIM

6 ½”

VP539

VP540

VP541

6” Round

7” Round

8” Round

16 ¾”

LOW PROFILE ROOF JACK

(MAXIMUM 4/12 PITCH)

MODEL DIM

10 ½”

VP552

VP553

10” Round

12” Round

22 ½”

20 ¾”

ADJUSTABLE ELBOW

MODEL DIM

VP513

VP514

VP515

6” Round

7” Round

8” Round

6”

7”

8”

VP513 - 8 ½”

VP514 - 9 ⁄”

VP515 - 10 ⁄”

BACK/SIDE VENT ELBOW

MODEL DIM

VP561 8” to 6” x 8 ½”

12”

6”

16”

8” Round

8 ½”

WALL LOUVER

MODEL DIM

6”

7”

8”

8 ⁄”

VP526

VP527

VP528

6” Round

7” Round

8” Round

Back

View

1 ½” Flange

WALL LOUVER

MODEL DIM

11”

VP554 10” Round

Back

View

1 ½” Flange

WALL LOUVER

MODEL DIM

13”

VP555 12” Round

Back

View

1 ½” Flange

RECTANGULAR WALL LOUVER

MODEL DIM

3 ¼”

10”

VP538

VP560

6” x 8 ½“

3 ¼” x 10”

8 ½”

6”

1 ½” FLANGE

2” FLANGE

OFFSET KIT - ROUND

MODEL DIM

VP529 6” Rnd to 7”Rnd

16”

11”

6”

7”

10 ½”

6” & 8” COLLAR

MODEL DIM

VP533

VP535

6” Round

8” Round

2” Larger

Than Cutout

6” Dia.

8” Dia.

2” Larger

Than Cutout

This manual suits for next models

Table of contents

Other VentAHood Ventilation Hood manuals

VentAHood

VentAHood ZTH User manual

VentAHood

VentAHood AH12 User manual

VentAHood

VentAHood ISLAND User manual

VentAHood

VentAHood Ventilation Hood Models Equipped with K250... User manual

VentAHood

VentAHood JPH/C1 DESIGNER series User manual

VentAHood

VentAHood Magic Lung Blower Operating manual

VentAHood

VentAHood EUROLINE User manual

VentAHood

VentAHood K250 ARS User manual

VentAHood

VentAHood CWEH6-K User manual

VentAHood

VentAHood JCH/A1 DESIGNER SERIES User manual

VentAHood

VentAHood Ventilation Hood Models Equipped with K250... Operating manual

VentAHood

VentAHood M600 User manual

VentAHood

VentAHood B100 Single 300 CFM User manual

VentAHood

VentAHood Under Cabinet Range Hood SL6 User manual

VentAHood

VentAHood K250 ARS User manual

VentAHood

VentAHood WALL MOUNT HOOD User manual

VentAHood

VentAHood Retro Style Under Cabinet Rangehood CLH9 User manual

VentAHood

VentAHood 300 CFM B100 User manual

VentAHood

VentAHood JCH/B1 Series User manual

VentAHood

VentAHood EUROLINE User manual

VentAHood

VentAHood WALL MOUNT HOOD User manual

VentAHood

VentAHood M600 User manual

VentAHood

VentAHood SLH6-K User manual

VentAHood

VentAHood K-SERIES User manual

Popular Ventilation Hood manuals by other brands

emmeti

emmeti RECUPA MED A-140 Installation and use manual

Nibe

Nibe F135 user manual

Kuppersberg

Kuppersberg INTRO 60 Technical Passport

Zephyr

Zephyr Spruce AK9834BS Use, care and installation guide

Hisense

Hisense MH6INBG manual

Miele

Miele DA 1255 Operating and installation instructions

Broan

Broan 46000 Specification sheet

GE Profile PV977 Owner's Manual & Installation Instructions

FALMEC

FALMEC FFRIA24W5FS Instruction booklet

Whirlpool

Whirlpool RH2600XL-1 SERIES installation instructions

Küppersbusch

Küppersbusch DX ISLA instruction manual

ETNA

ETNA AV360RVS Instructions for use

JUNO

JUNO JDF603E6 installation manual

Miele

Miele DA 6708 D Operating and installation instructions

Tricity Bendix

Tricity Bendix LE 150 Installation & operating instructions

AEG

AEG X68163BV1 user manual

AEG

AEG 125 D operating instructions

Smeg

Smeg KSEV97X instruction manual