VentAHood PYD18 User manual

FOR PYD18 EUROPA VENT-A-HOODS

INSTALLATION INSTRUCTIONS

A. Installation Work and Electrical Wiring Must Be Done By

Qualified Person(s) In Accordance With All Applicable

Codes And Standards, Including Fire-Rated Construction.

B. When cutting or drilling into wall or ceiling, do not

damage electrical wiring and other hidden utilities.

C. Ducted fans must always be vented to the out-

doors.

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

WARNING - TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.

D. Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of fuel

burning equipment to prevent back drafting. Follow the

heating equipment manufacturers guideline and safety

standards such as those published by the NationaI Fire

Protection Association (NFPA), and the American

Society for Heating, Refrigeration and Air Conditioning

Engineers (ASHRAE), and local code authorities.

Read and Save These Instructions

Turn Page For More Instructions

All Hoods Should Be Installed By A Qualified Installer

Step 1 . . .

Step 3 . . .

Step 2 . . .

Step 5 . . .

Step 4 . . .

Set hood on floor with

wood pallet still attached

to top.

Remove blower deck, light

assembly and transition from

hood.

Run 8 diameter duct and

wiring through ceiling with

section long enough to

reach transition on hood.

Install duct cover to load

bearing framing in

ceiling. For additional

stability in duct covers

over 24 tall, use 1/4 all-

threaded rods.

Attach hood to bottom of duct cover

and re-install blower and light units.

LOAD BEARING FRAMING

(furnished by others)

MOUNTING PLATES ON EACH CORNER

DUCT COVER

4 MOUNTING HOLES

LOCATED IN CORNERS

HOOD

LOAD BEARING FRAMING

CEILING

8 DUCT

TRANSITION

DECK

T200 BLOWER

5 x 16 to 8 DIAMETER

VP546

TRANSITION

FURNISHED

WITH HOOD

1000 N. Greenville Ave. = P.O. Box 830426 =Richardson, TX 75083 =(972) 235-5201

Methods of Ducting Your Vent-A-Hood

Venting Materials Available from Vent-A-Hood

- Step 6.  Connect ducting. 

1. Attach venting (before replacing deck if necessary). Do not restrict ducting anywhere

including roof jacks or wall louvers. Do not turn sharp turns with ducting. Make gradual turns

or 45°angles.

- Step 7.  Connect electrical. 

Follow label instructions and remove motor plate. Unplug motor and remove, being careful to not damage blower wheel. Connect electrical, black to

black, white to white and ground to lug provided. Replace motor(s) and dont forget to plug them back in. Replace blower front and be sure it is secured

properly and blower wheel(s) turn freely. Model T200, 3.4 Amps. Hoods with heat lamps and/or halogen lamps, 8.0 Amps.

Observe All Governing Codes and Ordinances

Proper transition is

furnished with hood.

dia.

Mounts under furr-down

Mounts to 8 ceiling

Standard Details

Transition to 8 round

duct furnished

Lip 3

Slope 6

Offset

1 

Blower

Minimum Round

Duct Size

Square

Inches

T-200 Dual 600 CFM 8 (or equivalent) 50

For use on all T-200

blowers with 8 duct

8 8

5 16

12

Other transitions by Special Order

Caution: To reduce the risk of fire or electrical shock, do not use this fan with any solid state variable speed control device.

Roof Jack

tape

8 LP Roof Jack

17 1

Round Vent Duct

6,7,8,9

8 Adjustable Elbow

8 Wall Louver

Offset L&R Transition

Side Vent Transition L & R

Island Transition

Wall Louver Venting

in 2-Story Dwelling

Hood

Floorline

(2nd floor)

Ceiling Line

(1st floor)

tape

Duct

Outside

Wall

Open

area --

screen

8 Roof Jack

161

specify

roof pitch

Europa Hoods

Motor Cooling Vent

Wiring Outlet

16

5

8

dia.

2 

7

2/25/99 II-PYD18

Table of contents

Other VentAHood Ventilation Hood manuals

VentAHood

VentAHood JCH/B1 Series User manual

VentAHood

VentAHood Ventilation Hood Models Equipped with K250... User manual

VentAHood

VentAHood K-SERIES User manual

VentAHood

VentAHood EUROLINE User manual

VentAHood

VentAHood CILH9 ISLAND RANGE HOOD User manual

VentAHood

VentAHood PYH302266 User manual

VentAHood

VentAHood VP526 User manual

VentAHood

VentAHood JCH/B1 Series User manual

VentAHood

VentAHood EUROLINE User manual

VentAHood

VentAHood EUROLINE User manual

VentAHood

VentAHood M600 User manual

VentAHood

VentAHood K250 ARS User manual

VentAHood

VentAHood EUROLINE User manual

VentAHood

VentAHood JPH/C1 DESIGNER series User manual

VentAHood

VentAHood B100 Single User manual

VentAHood

VentAHood Ventilation Hood Models Equipped with K250... Operating manual

VentAHood

VentAHood JPH DESIGNER SERIES User manual

VentAHood

VentAHood EUROLINE User manual

VentAHood

VentAHood DAH18 User manual

VentAHood

VentAHood K250 ARS User manual

VentAHood

VentAHood EUROLINE User manual

VentAHood

VentAHood SLH6-K User manual

VentAHood

VentAHood Equipped with Magic Lung Blower Operating manual

VentAHood

VentAHood V-Line K250 User manual

Popular Ventilation Hood manuals by other brands

emmeti

emmeti RECUPA MED A-140 Installation and use manual

Nibe

Nibe F135 user manual

Kuppersberg

Kuppersberg INTRO 60 Technical Passport

Zephyr

Zephyr Spruce AK9834BS Use, care and installation guide

Hisense

Hisense MH6INBG manual

Miele

Miele DA 1255 Operating and installation instructions

Broan

Broan 46000 Specification sheet

GE Profile PV977 Owner's Manual & Installation Instructions

FALMEC

FALMEC FFRIA24W5FS Instruction booklet

Whirlpool

Whirlpool RH2600XL-1 SERIES installation instructions

Küppersbusch

Küppersbusch DX ISLA instruction manual

ETNA

ETNA AV360RVS Instructions for use

JUNO

JUNO JDF603E6 installation manual

Miele

Miele DA 6708 D Operating and installation instructions

Tricity Bendix

Tricity Bendix LE 150 Installation & operating instructions

AEG

AEG X68163BV1 user manual

AEG

AEG 125 D operating instructions

Smeg

Smeg KSEV97X instruction manual