Vent-Axia PoziDry Compact Pro Assembly instructions

PLEASE READ INSTRUCTIONS IN CONJUNCTION WITH THE ILLUSTRATIONS.

PLEASE SAVE THESE INSTRUCTIONS

PoziDry

Compact Pro

Positive Input Ventilation Unit

Installation and Wiring Instructions

Stock Ref. N°

479188 –PoziDry Compact Pro

220-240V~50Hz



Installation and Wiring Instructions for the

PoziDry Compact Pro Positive Ventilation Unit.

INTRODUCTORY NOTES

The Unit is a positive input ventilation unit, designed to be installed on a wall of a dwelling to continually supply

filtered fresh air into the building. The system consists of a fan unit with heater.

The Unit has an adjustable speed settings. These speeds are set during installation; there are 4 pre-set speeds or an

option allowing the speeds to be chosen manually from 10 L/s - 30 L/s. The Unit uses a sensor to monitor the supply

temperature into the room. If the ambient room temperature exceeds 27°C (adjustable during commissioning), the

unit will automatically switch to standby (no airflow), unless installed in radon mode (selectable during

commissioning).

All models are supplied with a heater; the element is activated by default when the supply air temperature drops

below the adjustable threshold. The heater will try and maintain the supply air temperature at the threshold

temperature. The threshold temperature can be adjusted during commissioning.

The unit also incorporates a data logging function. This function will display total runtime of system, energy

consumption of the fan and energy consumption of the heater. This data is resettable (when in data logging menu,

hold the + and –button for 15 seconds until you see the word “RESET” on the display).

SAFETY AND GUIDANCE NOTES

IMPORTANT:

READ THESE INSTRUCTIONS BEFORE COMMENCING THE INSTALLATION

1.DO NOT install this product in areas where the following may be present or occur:

1.1. Excessive oil or a grease laden atmosphere.

1.2. Corrosive or flammable gases, liquids or vapours.

1.3. Ambient temperatures higher than 40°C or less than -10°C.

1.4. Possible obstructions which would hinder access or removal of the Fan.

1.5. Relative humidity above 90%

1.6. Sudden ductwork bends or transformations close to the Unit.

1.7. Unit must be mounted over 1.8m from floor level.

2. All wiring to be in accordance with the current I.E.E. Regulations, or the appropriate

standards of your country and MUST be installed by a suitably qualified person.

3. The fan must be provided with a 3A fused, isolator switch capable of disconnecting all

poles, having a contact separation of at least 3mm.

4. Ensure that the mains supply (voltage, frequency, and phase) complies with the fan’s

rating label.

5. The fan should not be used where it is liable to be subjected to direct water spray.

7. This appliance can be used by children aged from 8 years and above and persons

with reduced physical, sensory or mental capabilities or lack of experience and

knowledge if they have been given supervision or instruction concerning use of the

appliance in a safe way and understand the hazards involved. Children shall not play

with the appliance. Cleaning and user maintenance shall not be made by children

without supervision.

8. Precautions must be taken to avoid the back-flow of gases into the room from the

open flue of gas or other fuel-burning appliances.

9. Children of less than 3 years should be kept away unless continuously supervised.

10. Children aged from 3 to 8 years shall only switch on/off the appliance provided the

unit is installed as intended for normal operation and they have been given

supervision or instruction concerning safe use of the appliance and understand the

hazards involved.

11. Children aged 3 to 8 shall not plug in, regulate and clean the appliance or perform

user maintenance.

Caution - some parts of this product can become very hot and cause burns. Particular

attention has to be given where children and vulnerable people are present.

UNIT SIZE

UNIT MOUNTING

Unit to be mounted horizontally

Unit must be mounted over 1.8m from floor level.

INSTALLATION

The Unit is wall-mounted using the bracket and fixings supplied (or other suitable fasteners).

The wall should have sufficient strength to support the unit.

Take into consideration the routing of the cable and the ducting that must be fitted to the inlet spigot.

The unit can be mounted vertically or horizontally on a vertical wall.

Hand tighten these 2

screws, when fitting

the scroll assembly.

Feed power supply

through Base plate or

bottom left hand side

of unit, then through

the rear of the foam

before securing unit.

INLET OPTIONS

OPTION - 1

OPTION - 2

If installing the unit with the air supply

coming through the rear, the metal

plate cut-out will need to be removed from

base plate and the rear foam

case will need to be cut-out before mounting.

See next page for details.

Base Plate

Rear Foam

Using the centre mark, cut through the foam housing using a hole saw

Snip the three tabs to remove the insert

OUTLET OPTIONS

OPTION - 1

OUTLET OPTIONS

OPTION - 2

OUTLET OPTIONS

OPTION - 3

FILTER INSTALLATION

Please make sure the filter is fitted correctly and retained on top of the scroll. This will ensure that all the fresh air

entering the dwelling has passed through the filter first.

Slide filter on top of scroll

Push filter over retaining clip

to secure it in place.

Table of contents

Other Vent-Axia Fan manuals

Vent-Axia

Vent-Axia Lo-Carbon Tempra P Assembly instructions

Vent-Axia

Vent-Axia Solo Series User manual

Vent-Axia

Vent-Axia 45 90 49 (Pullcord) Assembly instructions

Vent-Axia

Vent-Axia Lo-Carbon Silhouette 100HT Assembly instructions

Vent-Axia

Vent-Axia Solo Pro Series Assembly instructions

Vent-Axia

Vent-Axia Lo-Carbon PureAir Home Series Assembly instructions

Vent-Axia

Vent-Axia Lo-Carbon iQ User manual

Vent-Axia

Vent-Axia PUREAIR SENSE User manual

Vent-Axia

Vent-Axia Lo-Carbon Square TM Assembly instructions

Vent-Axia

Vent-Axia Lo-Carbon Minivent Series Assembly instructions

Vent-Axia

Vent-Axia Lo-Carbon SOLO Plus SELV Series Assembly instructions

Vent-Axia

Vent-Axia HR400 User guide

Vent-Axia

Vent-Axia RMV 200 User manual

Vent-Axia

Vent-Axia Lo-Carbon PoziDry Pro Series Assembly instructions

Vent-Axia

Vent-Axia INTEGRA PLUS Assembly instructions

Vent-Axia

Vent-Axia LuminAir Kit L User manual

Vent-Axia

Vent-Axia Lo-Carbon Quadra SELV Series Assembly instructions

Vent-Axia

Vent-Axia Lo-Carbon Response 7 HTP Assembly instructions

Vent-Axia

Vent-Axia Sentinel Operating instructions

Vent-Axia

Vent-Axia Centrif Duo Series Assembly instructions

Vent-Axia

Vent-Axia ACM100 B Assembly instructions

Vent-Axia

Vent-Axia 17104010C Assembly instructions

Vent-Axia

Vent-Axia Lo-Carbon Quadra Assembly instructions

Vent-Axia

Vent-Axia Solo Plus P Assembly instructions

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual