Vent-Axia ACM100 B Assembly instructions

PLEASE READ INSTRUCTIONS IN CONJUNCTION WITH THE ILLUSTRATIONS.

PLEASE SAVE THESE INSTRUCTIONS

ACM In-Line

MIXED FLOW FANS

Stock Ref. N°

ACM100 B 17104010D

ACM100 T 17104020F

ACM125 B 17105010D

ACM125 T 17105020C

ACM150 B 17106010C

ACM150 T 17106020D

ACM160 B 17107010B

ACM160 T 17107020B

ACM200 B 17108010C

ACM200 T 17108020B

Installation and Wiring Instructions

220-240V~50Hz

IP44

Installation and Wiring Instructions for the ACM IN-LINE MIXED FLOW FAN range.

IMPORTANT: READ THESE INSTRUCTIONS

BEFORE COMMENCING THE INSTALLATION

DO NOT install this product in areas where the following may

be present or occur:

•Excessive oil or a grease laden atmosphere.

•Corrosive or flammable gases, liquids or vapours.

• Ambient temperatures higher than 40°C or less than –5°C.

• Possible obstructions which would hinder the access or

removal of the Fan.

•Sudden ductwork bends or transformations close to the Fan.

SAFETY AND GUIDANCE NOTES

A. All wiring to be in accordance with the current I.E.E.

Regulations, or the appropriate standards of your country

and MUST be installed by a suitably qualified person.

B.The Fan should be provided with a local double pole isolator

switch having a contact separation of at least 3mm.

C.Ensure that the mains supply (Voltage, Frequency, and

Phase) complies with the rating label.

D.The Fan should only be used in conjunction with the

appropriate Vent-Axia products.

E.It is recommended that the connection to the fan connecter

terminals is made with flexible cable.

F.When the Fan is used to remove air from a room containing a

fuel-burning appliance, precautions must be taken to avoid

back-flow of gases into the room from the open flue of gas or

other appliance. Ensure that the air replacement is adequate

for both the fan and the fuel-burning appliance.

G. The Fan should not be used where it is liable to be subject to

direct water spray for prolonged periods of time.

H.Where ducted Fans are used to handle moisture-laden air, a

condensation trap should be fitted. Horizontal ducts should

be arranged to slope slightly downwards away from the Fan.

I. This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless they

have been given supervision or instruction concerning use of

the appliance by a person responsible for their safety.

J. Young children should be supervised to ensure that they do

not play with the appliance.

A. INSTALLATION.

The unit is designed as an in-line duct fan to be positioned between lengths of ducting. Short duct runs terminating close to the

fan (i.e. within 1.5m) must incorporate suitable guards unless the fan is mounted higher than 2.1m above the floor. If flexible

ducting is used it should be fully extended to obtain the best results. Position the fan at the highest point on the system with both

ducting runs sloping downwards from this point. The airflow direction is indicated on the rating label with an arrow pointing in the

direction of the airflow. In circumstances where an excessive amount of moisture is present in the air then a condensation trap

should be installed. (Refer to Fig 15 for overall fan dimensions and fixing hole positions). When siting the appliance ensure that

there is sufficient space to allow access for any servicing and maintenance.

To gain access to the mounting holes, proceed as follows: -

A. Using a cross-headed screwdriver, release the two blue plastic clips by undoing the two bolts as shown in Fig 1. Slide

out motor impeller assembly, see Fig 2.

B. The fan can now be mounted at any angle, using the holes provided Fig 3,4,5,6 & 15

C. Once the base is securely fixed, slide the motor impeller assembly back, as shown in Fig 7. Replace the screw and

tighten to lock the assembly together Fig 8.

1 3

5 6 8

11 - Timer Models

10 - Basic Models

Timer adjuster

WIRING.

WARNING: THE FAN AND ANCILLARY CONTROL EQUIPMENT MUST BE ISOLATED FROM

THE POWER SUPPLY DURING THE INSTALLATION / OR MAINTENANCE.

THE ACM FANS ARE DOUBLE INSULATED AND CARRY A MARK. THERE ARE NO EARTH TERMINALS

AND THESE FANS MUST NOT BE EARTHED.

1. Remove terminal box cover & screws and put to one side Fig. 9

2. Select and follow the appropriate wiring diagram (Fig. 10-11).

3. Check all connections have been made correctly and ensure all terminal connections and cable clamps are

securely fastened. (Fig 12)

4. The cable entry must be made using the cable grommet provided

5. Replace terminal box cover & screws Fig.13

6. Ensure the impeller rotates and is free from obstructions

(Timer models cannot be used with a speed controller)

Timer Adjustment.

The fan must be wired to a remote switch (e.g. light switch).

When switched ‘ON’, the fan will operate at the selected

speed, and will continue to run for a preset time after the fan

is switched ‘OFF’. The timer is factory set at 15 minutes

approx. The overrun time period can be adjusted from 3-25

minutes by altering the adjuster on the control PCB with the

use of a small flat bladed screwdriver. Fig 13

Before adjusting the timer, switch off the Mains Supply.

Remove the fan terminal box cover and retain screws

To INCREASE the operating time, turn the adjuster CLOCKWISE.

To REDUCE the operating time, turn the adjuster ANTI-CLOCKWISE.

Replace the fan terminal box cover.

1312

Speed adjustment jumper

Speed Adjustment

The fan has three speeds which are selectable by changing the position of the jumper. The fan is factory set to

Setting 3 - High speed. To change the speed setting, pull the jumper off the header pins and place back onto the

desired position, see Fig14.

Setting 1 is LOW SPEED

Setting 2 is MEDIUM SPEED

Setting 3 is HIGH SPEED

Variable Speed Controller

Speed adjustment for the basic version can also be achieved with the use of a speed controller (stock reference

W300310). If a speed controller is used then the speed setting on the fan unit should be setting 3 – High Speed.

Follow the Installation and wiring instructions for the speed controller unit to install the controller correctly. A

variable speed controller should NOT be used with the timer version.

OVER-HEATING PROTECTION.

The fan motor is fitted with Thermal Overload Protection. This is a one-shot thermal fuse. In the event of a fault

condition the fan will be automatically switched off. If this occurs isolate the fan, and call your service engineer.

SERVICING AND MAINTENANCE.

WARNING:

THE FAN AND ANCILLARY CONTROL EQUIPMENT MUST BE ISOLATED

FROM THE POWER SUPPLY DURING MAINTENANCE.

1. At intervals appropriate to the installation, the fan should be inspected and cleaned to ensure there is no build

up of dirt or other deposits.

The ACM In-Line Mixed Flow fan has sealed for life bearings, which do not require lubrication.

Dimensions(mm)

100 125 150 160 200

AØ 98 122 147 159 198

BØ 178 178 200 200 220

C 124 124 138 138 138

D 298 259 307 352 300

E 96 96 118 118 130

F 168 168 192 192 145

FIXING CTRS

120 120 162 162 100

FIXING CTRS

153.5 153.5 178 178 180

Setting 1

LOW SPEED

Setting 2

MEDIUM SPEED

Setting 3

HIGH SPEED

PRODUCT FICHE

For Residential Ventilation Units (Complying Commission Delegated Regulation (EU) No

1254/2014)

Basic Models:

Name: Vent‐Axi a Vent‐Ax i a Vent‐Ax i aVent‐Ax i aVent‐Axi a 

ModelID(StockRef.):ACM100‐

17104010D

ACM125‐

17105010D

ACM150‐

17106010C

ACM160‐

17107010B

ACM200‐

17108010C

Declaredas:RVUorNRVU/UVUorBVU NRVU/UVU NRVU/UVU NRVU/UVU NRVU/UVU NRVU/UVU

SpeedDrive MultiSpeed Mul ti Speed MultiSpeed Mu l ti Speed MultiSpeed

TypeHRS(Recuperati ve,Regenerative,None) None None None None None

Thermal Eff:[(%),NA(ifnone)] N/A N/A N/A N/A N/A

Nominal FlowRate(m3/s) 0.06 0.07 0.11 0.11 0.18

EffectiveElec.PowerInput(kW):(@Nom.FlowRate&Ext.Pressure) 0.02 0.03 0.05 0.05 0.10

SFPint[W/(m3/s)] N/A N/A N/A N/A N/A

FaceVeloci ty(m/s)@DesignFlowRateN/A N/A N/A N/A N/A

Nominal External Pressure:(Δp

s,ext

)inPa 71 74 92 92 167

InternalPressureDropofVentilationComponents(Δp

s,int

)inPa; N/A N/A N/A N/A N/A

Addi tona l InternalPress.DropofNon‐VentilationComp.:Δp

s,add

(Pa) N/A N/A N/A N/A N/A

StaticEff.offansusedinaccordancewi thRegulation(EU)No

327/2011; TBCTBCTBCTBCTBC

Declared:‐MaxInternal&Externa l Leaka geRates(%)forBVUsor

carryover(forregenerativeheatexchangersonly),

‐&Ext.Lea kageRates(%)forDuctedUVUs;

N/A N/A N/A N/A N/A

EnergyPerformance,p refera bl yenergyclassification,oftheFilters

(declaredinformationaboutthecalculatedAEC) N/A N/A N/A N/A N/A

FilterWarning(RVU) NoNoNoNoNo

ForUVUs (InstructionsInstallGrillesFaçade) InF&W InF&W InF&W InF&W InF&W

InternetAddress(forDisassemblyIns tructions) www.vent‐axi a .com www.vent‐axi a.com www.vent‐axi a .com www.vent‐axi a.com www.vent‐axia.com

PRODUCT FICHE

For Residential Ventilation Units (Complying Commission Delegated Regulation (EU) No

1254/2014) - Continued

Timer Models:

Name: Vent‐Axi a Vent‐Axi a Vent‐Ax i aVent‐Ax i aVent‐Ax i a

ModelID(StockRef.):ACM100T‐

17104020F

ACM125T‐

17105020C

ACM150T‐

17106020D

ACM160T‐

17107020B

ACM200T‐

17108020B

Declaredas:RVUorNRVU/UVUorBVU NRVU/UVU NRVU/UVU NRVU/UVU NRVU/UVU NRVU/UVU

SpeedDrive MultiSpeed MultiSpeed Mul tiSpeed MultiSpeed Mu l ti Speed

TypeHRS(Rec uper a ti ve,Regenerative,None) None None None None None

Thermal Eff:[(%),NA(i fnone)] N/A N/A N/A N/A N/A

Nomi nalFlowRate(m3/s) 0.06 0.07 0.11 0.11 0.18

EffectiveElec.PowerInput(kW):(@Nom.FlowRate&Ext.Pressure)0.020.030.050.050.10

SFPint[W/(m3/s)] N/A N/A N/A N/A N/A

FaceVel oc i ty(m/s)@DesignFlowRateN/AN/AN/AN/AN/A

Nomi nalExternalPressure:(Δp

s,ext

)inPa 71 74 92 92 167

InternalPressureDropofVentilationComponents(Δp

s,int

)inPa; N/A N/A N/A N/A N/A

AdditonalInternalPress.DropofNon‐Venti l a ti onComp.:Δp

s,add

(Pa) N/AN/AN/AN/AN/A

StaticEff.offansusedinaccordancewithRegulation(EU)No

327/2011; TBCTBCTBCTBCTBC

Declared:‐MaxInternal&ExternalLeakageRates(%)forBVUsor

carryover(forregenerativeheatexcha ngers only),

‐&Ext.LeakageRates(%)forDuctedUVUs;

N/AN/AN/AN/AN/A

EnergyPerformance,preferablyenergyclassification,oftheFilters

(declaredinformationaboutthecalculatedAEC) N/AN/AN/AN/AN/A

FilterWarning(RVU) NoNoNoNoNo

ForUVUs (InstructionsInstallGrillesFaçade) InF&W InF&W InF&W InF&W InF&W

InternetAddres s(forDisassemblyInstructions ) www.vent‐a xia.com www.vent‐axi a.com www.vent‐axi a.com www.vent‐axi a.com www.vent‐axia.com



Head Office: Fleming Way, Crawley, West Sussex, RH10 9YX. Tel: 01293 526062 Fax: 01293 551188

UK NATIONAL CALL CENTRE, Newton Road, Crawley, West Sussex, RH10 9JA

SALES ENQUIRIES: Tel: 0344 8560590 Fax: 01293 565169

TECHNICAL SUPPORT: Tel: 0344 8560594 Fax: 01293 532814

For details of the warranty and returns procedure please refer to www.vent-axia.com or write to Vent-Axia Ltd, Fleming Way, Crawley, RH10 9YX

409945B 0716

The Guarantee

Applicable only to products installed and used in the United Kingdom. For details of guarantee outside the United Kingdom contact your local

supplier.

Vent-Axia guarantees its products for two years from date of purchase against faulty material or workmanship. In the event of any part being found

to be defective, the product will be repaired, or at the Company’s option replaced, without charge, provided that the product:-

Has been installed and used in accordance with the instructions given with each unit.

Has not been connected to an unsuitable electricity supply. (The correct electricity supply voltage is shown on the product rating label

attached to the unit).

Has not been subjected to misuse, neglect or damage.

Has not been modified or repaired by any person not authorised by the company.

IF CLAIMING UNDER TERMS OF GUARANTEE

Please return the complete product, carriage paid to your original supplier or nearest Vent-Axia Centre, by post or personal visit. Please ensure

that it is adequately packed and accompanied by a letter clearly marked “Guarantee Claim” stating the nature of the fault and providing evidence of

date and source of purchase.

The guarantee is offered to you as an extra benefit, and does not effect your legal rights

This manual suits for next models

Table of contents

Other Vent-Axia Fan manuals

Vent-Axia

Vent-Axia HR400 User guide

Vent-Axia

Vent-Axia Lo-Carbon Silhouette Series Assembly instructions

Vent-Axia

Vent-Axia Lo-Carbon Centra Series Assembly instructions

Vent-Axia

Vent-Axia VASF100B Assembly instructions

Vent-Axia

Vent-Axia HR100W User guide

Vent-Axia

Vent-Axia 496711 User manual

Vent-Axia

Vent-Axia ACQ10012D Assembly instructions

Vent-Axia

Vent-Axia SUPRA 100 T Assembly instructions

Vent-Axia

Vent-Axia 14120020 User manual

Vent-Axia

Vent-Axia Eclipse 100XP 427281 Assembly instructions

Vent-Axia

Vent-Axia Lo-Carbon Scala Plus Series Assembly instructions

Vent-Axia

Vent-Axia PoziDry Pro Assembly instructions

Vent-Axia

Vent-Axia Centra Lo-Carbon SELV Series Assembly instructions

Vent-Axia

Vent-Axia Slimpak EC Series Assembly instructions

Vent-Axia

Vent-Axia NBR DMEV 100 Assembly instructions

Vent-Axia

Vent-Axia T-Series Assembly Instructions

Vent-Axia

Vent-Axia sentinel Kinetic MVHR series User manual

Vent-Axia

Vent-Axia Lo-Carbon Quadra Series Assembly instructions

Vent-Axia

Vent-Axia PUREAIR SENSE Instruction and safety manual

Vent-Axia

Vent-Axia Lo-Carbon dMEV Unit T Assembly instructions

Vent-Axia

Vent-Axia MVDC-MS Assembly instructions

Vent-Axia

Vent-Axia PUREAIR SENSE User manual

Vent-Axia

Vent-Axia LoWatt Series Assembly instructions

Vent-Axia

Vent-Axia HR300RW6 User guide

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual