Vent-Axia MFQ35014 Assembly instructions

Installation and Wiring Instructions

Vent-Axia controls must be used with this fan!

PLEASE READ ALL INSTRUCTIONS CAREFULLY BEFORE STARTING

INSTALLATION.

THESE INSTRUCTIONS SHOULD BE LEFT WITH THE END USER.

Square Mixed Flow Fans (MFQ)

MFQ35014

MFQ40014

MFQ45014

MFQ50014

MFQ40034

MFQ45034

MFQ50034

MFQ56034

MFQ56036

MFQ63034

MFQ63036

ORIGINAL INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

PLEASE READ ALL INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.

INSTALLATION AND WIRING INSTRUCTIONS SHOULD BE LEFT WITH END USER.

Air moving equipment may present mechanical, electrical or noise hazards. To minimize

risks associated with these potential hazards, it is essential that safety, installation,

operation and maintenance instructions are followed. Implementation of these

instructions should always be undertaken by technically competent personnel.

Potential mechanical hazards must be eliminated by guarding against access to the

rotating parts whilst the air moving equipment is operating. A range of guards are

available for this purpose from Vent-Axia.

Installation work, both mechanical and electrical, must be undertaken in accordance

with the safety and installation instructions before switching on the unit.

Maintenance work should not be attempted before first switching off and isolating the

fan and its control from the electrical supply and ensuring that it cannot be accidentally

turned back on again. It is essential to ensure that rotating parts have come completely

to rest before maintenance work commences.

Air moving equipment may generate unacceptable noise levels when in operation. It

may be necessary to take appropriate action to reduce sound levels. A range of products

are available for this purpose from Vent-Axia.

This appliance is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities or lack of experience and knowledge unless they

have been given supervision or instruction concerning use of this appliance by a person

responsible for their safety.

Young children should be supervised to ensure that they do not play with the appliance.

IMPORTANT

1. All electrical connections should be made by a properly qualified electrician. The fan

must be sited and connected in accordance with current I.E.E Wiring Regulations,

BS7671 (U.K.), or the appropriate standards in your country.

2. DO NOT use this appliance when the following are generated or present: Excessive

grease or oil laden air, corrosive or flammable atmospheres.

3. When the fan is installed in a room containing a fuel burning appliance, the installer

must ensure that the air replacement is adequate for both the fan and the fuel

burning appliance.

4. If a fan is used to supply air into a room, the installer must ensure that the fan

intake is located at least 600mm away from any flue outlet.

5. Site away from direct sources of heat. Ambient temperature range:

MFQ35014 -15oC to +60oC

MFQ40014 -15oC to +60oC

MFQ45014 -15oC to +60oC

MFQ50014 -15oC to +60oC

MFQ40034 -15oC to +60oC

MFQ45034 -15oC to +60oC

MFQ50034 -15oC to +60oC

MFQ56034 -15oC to +45oC

MFQ56036 -15oC to +60oC

MFQ63034 -15oC to +55oC

MFQ63036 -15oC to +60oC

6. When installing unit, take care not to damage electrical or other hidden utilities.

7. Check the details on the rating label for correct voltage, frequency, speed, phase

insulation class and IP rating.

8. Select the correct direction of rotation for the fan. Remove the rubber grommet fitted

in the sight port next to the terminal box to view rotation. Three phase units require

a trial connection. To change direction of rotation, interchange any two phase supply

leads.

9. It is the responsibility of the installer to ensure that all aspects of system design are

taken into consideration.

10. Due to the weight of units it is recommended that at least two people are involved in

the installation.

FAN MOUNTING

1. A duct mounted in-line fan. Short duct runs terminating close to the fan (i.e. within

1.5m) require suitable guards.

2. The fan can be mounted in a variety of ways and at any angle to suit the

application.

3. Plan the installation carefully, taking into consideration the safety points noted

above, before securely fixing the fan using appropriate screws, bolts, rubber

bushes, etc.

4. A range of accessories are available from Vent-Axia to assist installation including

flexible connectors, mounting feet, anti-vibration mounts and attenuators.

Suggested fan mounting using mounting feet and anti-vibration mounts.

GENERAL WIRING INSTRUCTIONS

WARNING – THE FAN AND ANY ANCILLARY CONTROL EQUIPMENT MUST BE

ISOLATED FROM THE POWER SUPPLY DURING INSTALLATION AND/OR

MAINTENANCE. THE EQUIPMENT MUST BE EARTHED.

1. All electrical connections should be made by a properly qualified electrician.

2. All wiring and connections must be carried out in accordance with current

regulations.

3. To comply with safety standards, an all pole isolator switch with a contact gap of at

least 3mm must be fitted adjacent to the fan.

4. Remove the cover from the terminal box to expose the main terminal block and the

thermal protection block (TK). The thermal protection device fitted is an automatic

resetting type which must always be included in the circuit. For ducted applications a

manual reset is required, an ancillary circuit will be required with the TK switch

connected into the circuit. To comply with safety standards, this product must

be installed with Vent-Axia overload relays or controls.

5. Connect the power supply from the local isolator (via any appropriate controls if

fitted) to the terminal box via the supplied cable gland using between 4.0mm and

7.0mm diameter cable. Refer to the wiring diagrams and select the appropriate

connections for the fan, controller or other devices as being installed. If in doubt,

please ask.

6. CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal

cut-out, this appliance must not be supplied through an external switching device,

such as a timer, or connected to a circuit that is regularly switched on and off by the

utility

7. Ensure that all earth connections have been made.

8. After making connections inside the terminal box, replace the cover ensuring that the

sealing gasket is in place. Also ensure that all cable gland nuts, grommets etc. have

been used correctly to prevent the ingress of water.

NOTES ON RUNNING

Before Connecting the power supply and running the Fan Check…

Are all links and wiring complete as per wiring diagram?

Are all fixings secured?

Are all relevant guards fitted?

Are all Circuit protection devices fitted?

Are all Terminal box covers and sealing glands secured?

Are all Earth connections secured?

Check that no hazard exists for persons in the locality of the fan. Switch on the fan and

check that the fan rotation is correct as per the direction arrows on the fan plate/casing.

If not, isolate power supply and check wiring. For three phase fans interchange of any

two phase leads on the supply will change rotation.

Check that the current (amps) taken by the fan does not exceed the current shown on

the rating plate.

INSTALLER AND ELECTRICAL CONTRACTOR RESPONSIBILITY

Vent-Axia Ltd, as suppliers of the equipment cannot be responsible for the final

installation and electrical connection of the product on site. We have made reasonable

effort to offer guidance and assistance but the installer and electrical contractor on site

have a responsibility for ensuring the equipment is safely and securely installed and

electrically/mechanically safe in accordance with statutory requirements.

The fans are supplied as a component to be incorporated into a ventilation system. The

final complete system installation that includes the fans MUST meet the requirements

of:-

Low voltage Directive 72/23/CEE

Machinery Directive 89/392/CE

Electromagnetic Compatibility Directive 89/336/CE

If the fan is installed in an area where there is possible danger to safety or health then

guards MUST be fitted.

Guards suitable for many applications are available from Vent-Axia Ltd.

Please remember that fans need maintenance, cleaning and inspection. Allow for

reasonable access for these operations to be carried out safely.

If in doubt, please ask.

ROUTINE INSPECTION/MAINTENANCE

THIS MUST BE UNDERTAKEN BY A COMPETENT PERSON.

ISOLATE UNIT FROM ELECTRICAL SUPPLY AND ENSURE THAT IT CANNOT BE

ACCIDENTALLY TURNED BACK ON.

1. We recommend that after three months the fan should be inspected and

cleaned to remove deposits on the impeller or motor. Thereafter, it should be

checked and cleaned periodically as experience dictates, or at least twice a

year.

2. If a build up of dirt/deposits is evident then this should be carefully cleaned off.

Please take care not to damage the fan or affect the balance of the impeller

motor assembly (balance weights may be fitted to the impeller).

3. The fan motors are fitted with ‘sealed for life’ bearings and should not require

maintenance under normal circumstances.

Wiring Diagrams:

Important Notes: - The electrical circuit must be protected with an all pole isolator

having a minimum of 3mm contact separation with suitable fuses or circuit breaker.

For ducted applications the Thermal Protector (TK) must be connected into a control

circuit in order to ensure that the fan cannot restart before the fault condition is cleared

and the circuit manually reset. To comply with safety standards, this product must

be installed with Vent-Axia overload relays or controls.

Vent-Axia D.O.L. Starter/Overload and Speed Controller stock reference

numbers:

Product Starter Overload Electronic

Controller

Auto

Transformer

Controller

MFQ35014 444744 444701 10303103A 10314103A

MFQ40014 444744 444702 10303103A 10314103A

MFQ45014 444744 444703 10303106A 10314105A

MFQ50014 444744 444705 10303110A 10314109A

MFQ40034 444747 444700 Not available 10314302A

MFQ45034 444747 444701 Not available 10314304A

MFQ50034 444747 444702 Not available 10314304A

MFQ56034 444747 444703 Not available 10314307A

MFQ56036 444747 444701 Not available 10314304A

MFQ63034 444747 444705 Not available 10314311A

MFQ63036 444747 444702 Not available 10314304A

Fig. 1

Single phase MFQ

Connected to a D.O.L. Starter

Fig. 2

Single phase MFQ

Connected to a D.O.L. Starter and an Auto Transformer Speed Controller with no TK

connections

Fig. 3

Single phase MFQ

Connected to an Electronic Speed Controller

Fig. 4

Three phase MFQ

Connected to a D.O.L. Starter

Fig. 5

Three phase MFQ

Connected to an Auto Transformer Speed Controller

Notes:-

This manual suits for next models

Table of contents

Other Vent-Axia Fan manuals

Vent-Axia

Vent-Axia Lo-Carbon Centra Series Assembly instructions

Vent-Axia

Vent-Axia Centrif Duo Assembly instructions

Vent-Axia

Vent-Axia Solo Pro Series Assembly instructions

Vent-Axia

Vent-Axia EMF35514 Assembly instructions

Vent-Axia

Vent-Axia VASF100B Assembly instructions

Vent-Axia

Vent-Axia Lo-Carbon Quadra Assembly instructions

Vent-Axia

Vent-Axia Lo-Carbon Scala Plus Series Assembly instructions

Vent-Axia

Vent-Axia LoWatt T Series Operating instructions

Vent-Axia

Vent-Axia Lo-Carbon Silhouette Series Assembly instructions

Vent-Axia

Vent-Axia SDX100B Assembly instructions

Vent-Axia

Vent-Axia 45 90 49 (Pullcord) Assembly instructions

Vent-Axia

Vent-Axia SDX Series Assembly instructions

Vent-Axia

Vent-Axia PUREAIR SENSE Instruction and safety manual

Vent-Axia

Vent-Axia SOLO Plus 427477A Assembly instructions

Vent-Axia

Vent-Axia T-Series Assembly Instructions

Vent-Axia

Vent-Axia MULTIVENT MVDCH Manual instruction

Vent-Axia

Vent-Axia Lo-Carbon SOLO Plus SELV Series Assembly instructions

Vent-Axia

Vent-Axia Sentinel Kinetic B Guide

Vent-Axia

Vent-Axia SUPRA 100 T Assembly instructions

Vent-Axia

Vent-Axia SUPRA 100 B Assembly instructions

Vent-Axia

Vent-Axia TX7WW Assembly Instructions

Vent-Axia

Vent-Axia Lo-Carbon iQ User manual

Vent-Axia

Vent-Axia SDX EC Series Assembly instructions

Vent-Axia

Vent-Axia Lo-Carbon SOLO Plus 427481A Assembly instructions

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual