Vent-Axia SDX100B Assembly instructions

PLEASE READ INSTRUCTIONS IN CONJUNCTION WITH THE ILLUSTRATIONS.

PLEASE SAVE THESE INSTRUCTIONS

SDX

In-Line Centrifugal Duct Fans

Stock Ref. N°

SDX100B

SDX125B

SDX150B

SDX200B

SDX250B

SDX315B

SDX150HB

SDX200HB

SDX250HB

SDX315HB

Installation and Wiring Instructions

220-240V~50Hz

Installation and Wiring Instructions for the SDX IN-LINE CENTRIFUGAL DUCT FAN range.

IMPORTANT: READ THESE INSTRUCTIONS BEFORE COMMENCING THE INSTALLATION

DO NOT install this product in areas where the following may be present or occur:

•Excessive oil or a grease laden atmosphere.

•Corrosive or flammable gases, liquids or vapours.

• Ambient temperatures higher than 40°C or less than –5°C.

• Possible obstructions which would hinder the access or removal of the Fan.

•Sudden ductwork bends or transformations close to the Fan.

SAFETY AND GUIDANCE NOTES

A. All wiring to be in accordance with the current I.E.E. Regulations, or the appropriate standards of your country and MUST be

installed by a suitably qualified person.

B. The Fan should be provided with a local double pole isolator switch having a contact separation of at least 3mm.

C. Ensure that the mains supply (Voltage, Frequency, and Phase) complies with the rating label.

D. The Fan should only be used in conjunction with the appropriate Vent-Axia products.

E. It is recommended that the connection to the fan connecter terminals is made with flexible cable.

F. When the Fan is used to remove air from a room containing a fuel-burning appliance, precautions must be taken to avoid

back-flow of gases into the room from the open flue of gas or other appliance. Ensure that the air replacement is adequate

for both the fan and the fuel-burning appliance.

G. The Fan should not be used where it is liable to be subject to direct water spray for prolonged periods of time.

H. Where ducted Fans are used to handle moisture-laden air, a condensation trap should be fitted. Horizontal ducts should be

arranged to slope slightly downwards away from the Fan.

I. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities,

or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the

appliance by a person responsible for their safety.

J. Young children should be supervised to ensure that they do not play with the appliance.

K. Note:- This is a class 1 appliance and MUST be earthed.

A. INSTALLATION.

The unit is designed as an in-line duct fan to be positioned between lengths of ducting. Short duct runs terminating close to the

fan (i.e. within 1.5m) must incorporate suitable guards unless the fan is mounted higher than 2.1m above the floor. If flexible

ducting is used it should be fully extended to obtain the best results. Position the fan at the highest point on the system with both

ducting runs sloping downwards from this point. In circumstances where an excessive amount of moisture is present in the air

then a condensation trap should be installed. When siting the appliance ensure that there is sufficient space to allow access for

any servicing and maintenance.

Attaching the mounting feet

Select the image that relates to your fan.

For horizontal mounting

For horizontal mounting For Vertical mounting

For Vertical mounting

B. WIRING.

WARNING: THE FAN AND ANCILLARY CONTROL EQUIPMENT MUST BE ISOLATED FROM

THE POWER SUPPLY DURING THE INSTALLATION / OR MAINTENANCE.

THE SDX FANS ARE CLASS 1 AND MUST BE EARTHED.

1. Remove terminal box cover & screws and put to one side.

2. Select and follow the wiring diagrams.

3. Check all connections have been made correctly and ensure all terminal connections and cable clamps/gland

are securely fastened.

4. The cable entry must be made using the cable gland provided.

5. Replace terminal box cover & screws.

6. Ensure the impeller rotates and is free from obstructions

C. OVER-HEATING PROTECTION.

The fan motor is fitted with Thermal Overload Protection. This will automatically switch the fan off in the event of a

fault condition. If this occurs isolate the fan, check for and remove any obstruction, leave for a short time for the

motor to cool before reconnecting. If this recurs, Isolate and call your service engineer.

D. SERVICING AND MAINTENANCE.

WARNING: THE FAN AND ANCILLARY CONTROL EQUIPMENT MUST BE ISOLATED

FROM THE POWER SUPPLY DURING MAINTENANCE.

1. At intervals appropriate to the installation, the fan should be inspected and cleaned to ensure there is no build

up of dirt or other deposits.

The SDX fans have sealed for life bearings, which do not require lubrication.

230 Volt D.O.L. Starter

A suitable sized overload

relay must be fitted to

provide motor protection.

N.B. Links between

terminals 1 to A1 & 3 to 6,

must be fitted.

135

2395

96 24

N~ E

1 Phase Supply

(220-240V 50 Hz).

FAN TERMINALS

1 Phase Supply

(220-240V 50 Hz).

FAN TERMINALS

Switched spur

unit

Head Office: Fleming Way, Crawley, West Sussex, RH10 9YX. Tel: 01293 526062 Fax: 01293 551188

UK NATIONAL CALL CENTRE, Newton Road, Crawley, West Sussex, RH10 9JA

SALES ENQUIRIES: Tel: 0844 8560590 Fax: 01293 565169

TECHNICAL SUPPORT: Tel: 0844 8560594 Fax: 01293 539209

For details of the warranty and returns procedure please refer to www.vent-axia.com or write to Vent-Axia Ltd, Fleming Way, Crawley, RH10 9YX

446307A 0111

The abc Guarantee

Applicable only to products installed and used in the United Kingdom. For details of guarantee outside the United Kingdom contact your local

supplier.

Vent-Axia guarantees its products for two years from date of purchase against faulty material or workmanship. In the event of any part being found

to be defective, the product will be repaired, or at the Company’s option replaced, without charge, provided that the product:-

•Has been installed and used in accordance with the instructions given with each unit.

•Has not been connected to an unsuitable electricity supply. (The correct electricity supply voltage is shown on the product rating label

attached to the unit).

•Has not been subjected to misuse, neglect or damage.

•Has not been modified or repaired by any person not authorised by the company.

IF CLAIMING UNDER TERMS OF GUARANTEE

Please return the complete product, carriage paid to your original supplier or nearest Vent-Axia Centre, by post or personal visit. Please ensure

that it is adequately packed and accompanied by a letter clearly marked “Guarantee Claim” stating the nature of the fault and providing evidence of

date and source of purchase.

The guarantee is offered to you as an extra benefit, and does not effect your legal rights

This manual suits for next models

Table of contents

Other Vent-Axia Fan manuals

Vent-Axia

Vent-Axia Lo-Carbon Centra Series Assembly instructions

Vent-Axia

Vent-Axia Lo-Carbon iQ User manual

Vent-Axia

Vent-Axia Lo-Carbon Response 7 HTP Assembly instructions

Vent-Axia

Vent-Axia Azur 100B Assembly instructions

Vent-Axia

Vent-Axia eMF Series Assembly instructions

Vent-Axia

Vent-Axia FAN7200 User manual

Vent-Axia

Vent-Axia Lo-Carbon Scala Plus Assembly instructions

Vent-Axia

Vent-Axia EUROFLOW KDF Series Assembly instructions

Vent-Axia

Vent-Axia SOLO Plus 427477A Assembly instructions

Vent-Axia

Vent-Axia Lo-Carbon Sylph Series Assembly instructions

Vent-Axia

Vent-Axia PoziDry Compact Pro Assembly instructions

Vent-Axia

Vent-Axia 45 40 55B Assembly instructions

Vent-Axia

Vent-Axia MULTIVENT MV250 Assembly instructions

Vent-Axia

Vent-Axia Lo-Carbon Responce Series Assembly instructions

Vent-Axia

Vent-Axia MVDC-MS Assembly instructions

Vent-Axia

Vent-Axia NBR dMEV C 100 T Assembly instructions

Vent-Axia

Vent-Axia Response Series Assembly instructions

Vent-Axia

Vent-Axia MULTIVENT MV250H Assembly instructions

Vent-Axia

Vent-Axia HR300RW6 User guide

Vent-Axia

Vent-Axia VA 150 A Assembly instructions

Vent-Axia

Vent-Axia HR400 User guide

Vent-Axia

Vent-Axia Silhouette 439974 Assembly instructions

Vent-Axia

Vent-Axia ACM100 B Assembly instructions

Vent-Axia

Vent-Axia INTEGRA PLUS Assembly instructions

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual