Vent-Axia Eclipse 100XP 427281 Assembly instructions

Models Ref No.

Eclipse 100X 42 73 10A

Eclipse 100XP 42 72 81A

Eclipse 100XT 42 72 82A

Eclipse 150X 42 72 83A

Eclipse 150XP 42 73 13A

220

240V~50Hz

Eclipse

Installation and Wiring Instructions

PLEASE READ INSTRUCTIONS IN CONJUNCTION WITH ILLUSTRATIONS. PLEASE SAVE THESE INSTRUCTIONS.

Installation and Wiring Instructions for the Eclipse Range of Extractor Fans.

IMPORTANT:

READ THESE INSTRUCTIONS

BEFORE COMMENCING THE

INSTALLATION

DO NOT install this product in areas where the following may be present or occur:

•Excessive oil or a grease laden atmosphere.

•Corrosive or flammable gases, liquids or vapours.

• Ambient temperatures higher than 40°C or less than –5°C.

• Possible obstructions which would hinder the access or removal of the Fan.

SAFETY AND GUIDANCE NOTES

A. All wiring to be in accordance with the current I.E.E.

Regulations, or the appropriate standards of your country

and MUST be installed by a suitably qualified person.

B. The Fan should be provided with a local isolator switch

capable of disconnecting all poles, having a contact

separation of at least 3mm.

C. Ensure that the mains supply (Voltage, Frequency, and

Phase) complies with the rating label.

D. The Fan should only be used in conjunction with the

appropriate Vent-Axia products.

E. The fan should only be used in conjunction with fixed wiring.

F. When the Fan is used to remove air from a room containing

a fuel-burning appliance, ensure that the air replacement is

adequate for both the fan and the fuel-burning appliance.

G. The Fan should not be used where it is liable to be subject

to direct water spray for prolonged periods of time.

H. Where ducted Fans are used to handle moisture-laden air, a

condensation trap should be fitted. Horizontal ducts should

be arranged to slope slightly downwards away from the Fan.

I. This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concerning

use of the appliance by a person responsible for their safety.

J. Children should be supervised to ensure that they do not

play with the appliance.

K. Stationary appliances not fitted with means for disconnection

from the supply mains having a contact separation in all

poles that provide full disconnection under over voltage

category III, the instructions state that means for

disconnection must be incorporated in the fixed wiring in

accordance with the wiring rules.

DESCRIPTION

The Eclipse 100mm axial extract fans are suitable for domestic bathrooms and W.C’s. The Eclipse

150mm axial extract fans are suitable for domestic kitchens and utility rooms. They are available as wall

or panel mounted models with shutter, pullcord & timer combinations.

ACCESSORIES (not supplied)

WALL FITTING KIT

A range of 100mm and 150mm wall kits are available

for installing into most walls using telescopic liners

supplied.

A. INSTALLATION

PANEL MOUNTING

1. Cut a 105mm diameter hole for 100mm fans or a 155mm diameter hole for 150mm fans through the panel.

2. Remove the Inner Grille [A]. Insert a small bladed screwdriver between the bottom blade of the Inner Grille and

the Outer Bezel [B]. Gently lever the bottom grille blade upwards and away from the Outer Bezel.

3. Remove Outer Bezel. Remove the two screws retaining the Bezel to the Base Housing [D]. Please note that

the Outer Bezel is also secured into position via the central section and will require a small force to remove it.

4. Remove the Cable Grommet [C], and push the cable through the grommet including the outer core secondary

insulation. Please ensure the correct cable is used as outlined in Section C WIRING.

5. Slide the Base Housing into the hole in the panel and secure into position using screws and fixings provided.

6. Ensure the fan blade rotates freely.

7. Select and follow the appropriate wiring diagram in Section C WIRING.

8. Replace the Outer Bezel ensuring the centre section positively clips into the Base Housing by carefully pushing

from the centre.

9. Switch the mains power supply on and check the fan is operating correctly.

WALL MOUNTING (For wall installations see accessories table for a suitable wall kit).

1. Cut a 115mm diameter hole for 100mm fans or a 170mm diameter hole for 150mm fans through the wall and

insert the wall sleeve and cement both ends into position flush with the wall faces. The wall sleeve should be

angled downwards away from the fan to allow any condensation to drain to the outside wall.

2. Fix the outer grille as required, ensuring the louvres are pointing downwards.

Fan

Size

Stock Reference

White Brown

100mm 254102 254100

150mm 140902A 140903A





3. Remove the Inner Grille [A]. Insert a small bladed screwdriver between the bottom blade of the Inner Grille and

the Outer Bezel [B]. Gently lever the bottom grille blade upwards and away from the Outer Bezel.

4. Remove the Outer Bezel. Remove the two screws retaining the Bezel to the Base Housing [D]. Note that the

Outer Bezel is also secured into position via the central section and will require a small force to remove it.

5. Remove the Cable Grommet [C], and push the cable through the grommet including the outer core secondary

insulation. Please ensure the correct cable is used as outlined in Section C WIRING.

6. Slide the Base Housing into the Wall Liner and secure into position by tightening the Quick Clip screws [F]

(fig. 2).

7. Ensure the fan blade rotates freely.

8. Select and follow the appropriate wiring diagram in Section C WIRING.

9. Replace the Outer Bezel ensuring the centre section positively clips into the Base Housing by carefully pushing

from the centre.

10. Switch the mains power supply on and check the fan is operating correctly.

SETUP

WARNING: THE FAN AND ANCILLARY CONTROL EQUIPMENT MUST BE ISOLATED FROM

THE POWER SUPPLY DURING THE INSTALLATION / OR MAINTENANCE.

TIMER ADJUSTMENT (T model)

The overrun time period is factory set to 15 minutes. The overrun time period may be adjusted from 5-30

minutes by altering the adjuster on the control PCB.

i. To REDUCE the operating time, turn the adjuster (fig. 3.) CLOCKWISE.

ii. To INCREASE the operating time, turn the adjuster (fig. 3.) ANTI-CLOCKWISE.

C. WIRING.

WARNING: THE FAN AND ANCILLARY CONTROL EQUIPMENT MUST BE ISOLATED FROM

THE POWER SUPPLY DURING THE INSTALLATION / OR MAINTENANCE.

This product is designed for fixed wiring installations only. Flexible cord should not be used.

1. 1mm

or 1.5mm

solid/rigid core flat cable should be used.

2. Select and follow the appropriate wiring diagram (fig. 4/5).

3. Check all connections have been made correctly and ensure all terminal connections are securely fastened.

4. Ensure the integrity of the seal between the cable outer insulation and grommet and replace in the Base

Housing. THERE MUST BE NO GAPS BETWEEN THE GROMMET AND CABLE.

5. Ensure the impeller rotates and is free from obstructions.

D. SERVICING AND MAINTENANCE.

WARNING: THE FAN AND ANCILLARY CONTROL EQUIPMENT MUST BE ISOLATED

FROM THE POWER SUPPLY DURING MAINTENANCE.

1. At intervals appropriate to the installation, the fan should be inspected and cleaned to ensure there is no build

up of dirt or other deposits.

2. Wipe the inlets and front face with a damp cloth until clean.

The fan has sealed for life bearings, which do not require lubrication.

Base Housing

Quick Clip

Wall Liner

Wall

Fig. 3

Fig. 1.

A B C D E

A Grille

B Outer Bezel

C Cable Grommet

D Base Housing

E Shutter Assembly

F Quick Clip

Fig. 2.

1. 2.

Fig. 4.

Pull Cord (if applicable)

1 Phase Supply

(220-240 V 50 Hz)

Switched Fused Spur

Fan

Eclipse 100/150 X/XP

Fig. 5.

1 Phase Supply

(220-240 V 50 Hz)

Fuse

3 Pole Isolator Switch

Ceiling Junction

Eclipse 100 XT

Fan

L ~ N

Head Office: Fleming Way, Crawley, West Sussex, RH10 9Y

UK NATIONA CA CENTRE, Newton Road, Crawley, West Sussex, RH10 9JA

SALES ENQUIRIES: Tel: 0844 8560590 Fax: 01293 565169

TECHNICAL SUPPORT: Tel: 0844 8560594 Fax: 01293 539209

For details of the warranty and returns procedure please refer to www.vent-axia.com or write to Vent-Axia Ltd, Fleming Way, Crawley, RH10 9Y

403639B 0916

The Guarantee

Applicable only to products installed and used in the United Kingdom. For details of guarantee outside the United Kingdom contact your local

supplier.

Vent-Axia guarantees its products for two years from date of purchase against faulty material or workmanship. In the event of any part being found

to be defective, the product will be repaired, or at the Company’s option replaced, without charge, provided that the product:-

•Has been installed and used in accordance with the instructions given with each unit.

•Has not been connected to an unsuitable electricity supply. (The correct electricity supply voltage is shown on the product rating label

attached to the unit).

•Has not been subjected to misuse, neglect or damage.

•Has not been modified or repaired by any person not authorised by the company.

IF CLAIMING UNDER TERMS OF GUARANTEE

Please return the complete product, carriage paid to your original supplier or nearest Vent-Axia Centre, by post or personal visit. Please ensure

that it is adequately packed and accompanied by a letter clearly marked “Guarantee Claim” stating the nature of the fault and providing evidence of

date and source of purchase.

The guarantee is offered to you as an extra benefit, and does not effect your legal rights

Other manuals for Eclipse 100XP 427281

This manual suits for next models

Table of contents

Other Vent-Axia Fan manuals

Vent-Axia

Vent-Axia RMV 200 User manual

Vent-Axia

Vent-Axia Slimpak EC Series Assembly instructions

Vent-Axia

Vent-Axia INTEGRA PLUS Assembly instructions

Vent-Axia

Vent-Axia Lo-Carbon iQ User manual

Vent-Axia

Vent-Axia LoWatt T Series Operating instructions

Vent-Axia

Vent-Axia ATQ10012D Assembly instructions

Vent-Axia

Vent-Axia JUPITER315 Assembly instructions

Vent-Axia

Vent-Axia Centrif 179 User manual

Vent-Axia

Vent-Axia VA 150 A Assembly instructions

Vent-Axia

Vent-Axia ACM100 B Assembly instructions

Vent-Axia

Vent-Axia HR400 User guide

Vent-Axia

Vent-Axia 478075 User manual

Vent-Axia

Vent-Axia Advance S User manual

Vent-Axia

Vent-Axia Lo-Carbon Svelte Series Assembly instructions

Vent-Axia

Vent-Axia Azur 100B Assembly instructions

Vent-Axia

Vent-Axia T Series Assembly Instructions

Vent-Axia

Vent-Axia Lo-Carbon Scala Plus Series Assembly instructions

Vent-Axia

Vent-Axia PUREAIR SENSE Instruction and safety manual

Vent-Axia

Vent-Axia Lo-Carbon Scala Plus Assembly instructions

Vent-Axia

Vent-Axia VASF100B Assembly instructions

Vent-Axia

Vent-Axia Lo-Carbon VA150P Assembly instructions

Vent-Axia

Vent-Axia LuminAir Kit T User manual

Vent-Axia

Vent-Axia Sentinel Operating instructions

Vent-Axia

Vent-Axia T-Series Assembly Instructions

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual