Vent-Axia 45 40 55B Assembly instructions

Installation and Wiring Instructions

Stock Ref. N°

45 40 55B (100B)

44 51 61 (125B)

45 40 59B (150X)

45 40 56B (100T)

44 51 62 (125T)

45 40 60B (150XT)

45 40 57B (100HT)

44 51 63 (125HT)

45 40 61B (150XHT)

45 40 58B (100TM)

PLEASE READ INSTRUCTIONS IN CONJUNCTION WITH ILLUSTRATIONS.

PLEASE SAVE THESE INSTRUCTIONS.

Silhouette

IPX4

220-240V~50Hz

Vent- -

CE:

Installation and Wiring Instructions for the Silhouette Range of Extractor Fans.

IMPORTANT:

READ THESE INSTRUCTIONS

BEFORE COMMENCING THE

INSTALLATION

DO NOT install this product in areas where the following may be present or occur:

•Excessive oil or a grease laden atmosphere.

•Corrosive or flammable gases, liquids or vapours.

• Ambient temperatures higher than 40°C or less than –5°C.

• Possible obstructions which would hinder the access or removal of the Fan.

SAFETY AND GUIDANCE NOTES

A. All wiring to be in accordance with the current I.E.E. Regulations, or the appropriate standards of

your country and MUST be installed by a suitably qualified person.

B. The Fan should be provided with a local isolator switch capable of disconnecting all poles, having a

contact separation of at least 3mm.

C. Ensure that the mains supply (Voltage, Frequency, and Phase) complies with the rating label.

D. The Fan should only be used in conjunction with the appropriate Vent-Axia products.

E. The fan should only be used in conjunction with fixed wiring.

F. When the Fan is used to remove air from a room containing a fuel-burning appliance, ensure that

the air replacement is adequate for both the fan and the fuel-burning appliance.

G. The Fan should not be used where it is liable to be subject to direct water spray for prolonged

periods of time.

H. Where ducted Fans are used to handle moisture-laden air, a condensation trap should be fitted.

Horizontal ducts should be arranged to slope slightly downwards away from the Fan.

I. This appliance is not intended for use by persons (including children) with reduced physical, sensory

or mental capabilities, or lack of experience and knowledge, unless they have been given

supervision or instruction concerning use of the appliance by a person responsible for their safety.

J. Children should be supervised to ensure that they do not play with the appliance.

K. Stationary appliances not fitted with means for disconnection from the supply mains having a

contact separation in all poles that provide full disconnection under over voltage category III, the

instructions state that means for disconnection must be incorporated in the fixed wiring in

accordance with the wiring rules.

DESCRIPTION

The Silhouette 100mm & 125mm axial extract fans are suitable for domestic bathrooms and W.C’s. The

Silhouette 125mm & 150mm axial extract fans are suitable for domestic kitchens and utility rooms. They

are available as wall or panel mounted models with shutter timer, humidity and PIR combinations

(100mm model only).

ACCESSORIES (not supplied)

WALL FITTING KIT

A range of 100mm, 125mm and 150mm wall kits are

available for installing into most walls using telescopic

liners supplied.

Fan

Size

Stock Reference

White Brown

100mm 254102 254100

125mm 455226 N/A

150mm 140902A 140903A

A. INSTALLATION

IMPORTANT: The fan should only be used in conjunction with fixed wiring.

PANEL/CEILING MOUNTING

1. For panel/ceiling mounting the fan should be installed into a closed duct system of at least 1.2m

long or protected by an exterior air grille that must comply with the standard requirements of your

country to prevent access to the fans impeller.

2. Cut a 105mm diameter hole for 100mm fans, a 130mm hole for 125mm fans or a 155mm

diameter hole for 150mm fans.

3. Loosen the screw at the bottom of the grille and remove the front grille. Mark the screw centres

through the holes in the fan back plate. Drill, plug and screw into position.

4. Replace the grille and tighten the retaining screw.

5. After installation, ensure impeller rotates freely and the shutters can open.

WALL MOUNTING

1. For wall mounting either cut a 115mm diameter hole for 100mm fans, a 140mm hole for 125mm

fans or a 170mm diameter hole for 150mm fans, through the wall and insert the wall sleeve.

Slope the sleeve slightly downwards away from the fan. Cut to length and cement both ends into

position flush with the wall faces.

2. Loosen the screw in the bottom of the grille and remove the front grille. Mark the screw centres

through the holes in the fan back plate. Drill, plug and screw into position. Fix exterior grille into

position with the louvres positioned downwards. (Note:- The grille must comply with the standard

requirements of your country to prevent access to the fans impeller. The wall kit used in this

installation should provide a minimum ducting length of 60mm from the fans back plate to the

inside of the external grille).

3. Replace the grille and tighten the retaining screw.

4. After installation, ensure impeller rotates freely and the shutters can open.

B. WIRING.

WARNING: THE FAN AND ANCILLARY CONTROL EQUIPMENT MUST BE ISOLATED

FROM THE POWER SUPPLY DURING THE INSTALLATION / OR MAINTENANCE.

IMPORTANT

The fan should only be used in conjunction with fixed wiring.

The cross - sectional area of supply cord used should be ranged from 1 -1.5mm2.

Cable entry can only be made from the rear of the fan.

The extraction fan is suitable for connection to 220-240V 50Hz supply.

The fan is a class ll double insulated product and MUST NOT be earthed.

1. Select and follow the appropriate wiring diagram. (Fig. 2,3 or 4)

2. Check all connections have been made correctly and ensure all terminal connections and cable

clamps are securely fastened.

3. Ensure the impeller rotates and is free from obstructions.

C. SETUP

WARNING: THE FAN AND ANCILLARY CONTROL EQUIPMENT MUST BE ISOLATED

FROM THE POWER SUPPLY DURING THE INSTALLATION / OR MAINTENANCE.

NOTE

On all 150mm fans the shutter may take up to one minute to activate on start-up, and the same amount

of time to close when the fan is switched off.

SILHOUETTE 100B/125B/150X

Single speed fan. Controlled by remote switch (e.g. light switch or auto sensor) Fig.2.

SILHOUETTE 100T/125T/150XT

Single speed with overrun timer. The fan can be wired to a lighting circuit switch. Fig.4. or wired for a

basic on/off operation wire as Fig 3.

When switched ‘ON’, the fan will operate at full speed and will continue to run for a pre-set time after the

switch is turned ‘OFF’.

TIMER ADJUSTMENT

BEFORE ADJUSTING THE TIMER, SWITCH OFF THE MAINS SUPPLY. TIMER SHOULD

ONLY BE ADJUSTED BEFORE OR DURING INSTALLATION.

1. Remove the fan grille. The controller is factory set at 15 minutes approx. The overrun time

period can be adjusted from 5-25 minutes by altering the adjuster on the control PCB.

2. To REDUCE the operating time, use a small screwdriver to turn the adjuster Fig.5. ANTI-

CLOCKWISE.

3. To INCREASE the operating time, use a small screwdriver to turn the adjuster Fig.5.

CLOCKWISE.

4. Replace the fan grille.

SILHOUETTE 100HT/125HT/150XHT

The fan contains an integral humidity controller. In automatic mode the controller switches the fan on at

full speed when the room Relative Humidity (RH) reaches the set-point. The fan will continue to run until

the room RH falls below the set-point.

These fans also include a built in timer function. The timer can be activated by removing the Jumper

JP1, this will give the fan a fixed over run time of approx. 15 mins.

HUMIDITY SET-POINT ADJUSTMENT

BEFORE ADJUSTING THE CONTROLLER, SWITCH OFF THE MAINS SUPPLY. HUMIDISTAT

SHOULD ONLY BE ADJUSTED BEFORE OR DURING INSTALLATION.

1. Remove the fan grille. The controller is factory set to switch on at about 70% RH. The

humidity set point can be adjusted from 65-95%RH by altering the adjuster on the control

PCB.

2. To LOWER the set-point use a small screwdriver to turn the adjuster Fig.6. ANTI-

CLOCKWISE. This makes the controller MORE sensitive.

3. To RAISE the set-point use a small screwdriver to turn the adjuster Fig.6. CLOCKWISE.

This makes the controller LESS sensitive.

4. Replace the fan grille.

NOTE! DO NOT TOUCH HUMIDITY SENSOR.

SILHOUETTE 100TM

Single speed with PIR (passive infra-red) detector and overrun timer. The fan starts automatically when

a movement is detected and will continue to operate for the set overrun time period.

(See ‘Timer Adjustment’ section above) Fig. 2 and 5.

D. SERVICING AND MAINTENANCE.

WARNING: THE FAN AND ANCILLARY CONTROL EQUIPMENT MUST BE ISOLATED

FROM THE POWER SUPPLY DURING MAINTENANCE.

1. At intervals appropriate to the installation, the fan should be inspected and cleaned to ensure there is

no build up of dirt or other deposits.

2. Wipe the inlets and front face with a damp cloth until clean.

The fan has sealed for life bearings, which do not require lubrication.

Fig.2

Fig.3

Timer model wired as a Basic version (link between L & LS enables fan to switch on or off when power is put onto the fan).

Fig.1.

1 PHASE SUPPLY N

-+------s

:---+-----+------1

(220-240V 50Hz). -

L -

+---:

>--+-

----

-+--

-----<

SWITCH

SPUR Fan

PHASE

SUPP

-+----<

(220-24!0V 5GHz).

....,

L -

-1-----------,

ITCHED

SPUR

Fan

Fig.5. Fig.6.

Fig.4

Humidity

Adjustment

Timer

Adjustment

To activate the timer function remove jumper

JP1.

Once removed the fan will run on for a fixed

time period of approx. 15 mins.

To REDUCE the operating time, use a small

screwdriver to turn the adjuster ANTI-CLOCKWISE.

To INCREASE the operating time, use a small

screwdriver to turn the adjuster CLOCKWISE.

To LOWER the set-point use a small screwdriver to

turn the adjuster

ANTI-CLOCKWISE. This makes the controller

MORE sensitive.

To RAISE the set-point use a small screwdriver to

turn the adjuster CLOCKWISE. This makes the

controller LESS sensitive.

1 PHASE

(220-

240V

50Hz).

L- N

CEILING

JUNCTION

POLE

ISOLATOR

SWITCH

Fan



Head Office: Fleming Way, Crawley, West Sussex, RH10 9YX.

UK NATIONAL CALL CENTRE, Newton Road, Crawley, West Sussex, RH10 9JA

SALES ENQUIRIES: Tel: 0844 8560590 Fax: 01293 565169

TECHNICAL SUPPORT: Tel: 0844 8560594 Fax: 01293 532814

As part of the policy of continuous product improvement Vent-Axia reserves the right to alter specifications without notice.

449631C 0513

The Guarantee

Applicable only to products installed and used in the United Kingdom. For details of guarantee outside the United Kingdom contact your local

supplier.

Vent-Axia guarantees its products for two years from date of purchase against faulty material or workmanship. In the event of any part being found

to be defective, the product will be repaired, or at the Company’s option replaced, without charge, provided that the product:-

Has been installed and used in accordance with the instructions given with each unit.

Has not been connected to an unsuitable electricity supply. (The correct electricity supply voltage is shown on the product rating label

attached to the unit).

Has not been subjected to misuse, neglect or damage.

Has not been modified or repaired by any person not authorised by the company.

IF CLAIMING UNDER TERMS OF GUARANTEE

Please return the complete product, carriage paid to your original supplier or nearest Vent-Axia Centre, by post or personal visit. Please ensure

that it is adequately packed and accompanied by a letter clearly marked “Guarantee Claim” stating the nature of the fault and providing evidence of

date and source of purchase.

The guarantee is offered to you as an extra benefit, and does not effect your legal rights

••••••••••••••••••••••••••••••••••••••••

•

Vent-Axia :

•

•••••••••••••••••••••••••••••••••••••••••

Check out our full range of Bathroom Accessories

Bathroom Accessory Sets

Heated Towel Rails

Bathroom Extractor Fans

Bathroom Lighting

Shower Seats

Grab Rails

Shower Curtains

Toilet Brushes

Bathroom Cleaning Products

Wall Mounted Bathroom Accessories

Robe Hooks

Bathroom Tumblers

Toilet Roll Holders

Soap Dishes

Towel Rings

Shower Caddies

Bathroom Mirrors

Standard Bathroom Mirrors

LED Bathroom Mirrors

Shaving Mirrors

This manual suits for next models

Table of contents

Other Vent-Axia Fan manuals

Vent-Axia

Vent-Axia Lo-Carbon SOLO Plus 427481A Assembly instructions

Vent-Axia

Vent-Axia VA100/SELV Assembly instructions

Vent-Axia

Vent-Axia Lo-Carbon PoziDry Compact Series Assembly instructions

Vent-Axia

Vent-Axia LuminAir Kit T User manual

Vent-Axia

Vent-Axia Solo Pro Series Assembly instructions

Vent-Axia

Vent-Axia FAN7200 User manual

Vent-Axia

Vent-Axia Eclipse 100XP 427281 Assembly instructions

Vent-Axia

Vent-Axia PUREAIR SENSE Instruction and safety manual

Vent-Axia

Vent-Axia Lo-Carbon Silhouette SELV Series Assembly instructions

Vent-Axia

Vent-Axia EKF355E1 Assembly instructions

Vent-Axia

Vent-Axia VASF100B Assembly instructions

Vent-Axia

Vent-Axia Lo-Carbon Scala Plus Assembly instructions

Vent-Axia

Vent-Axia sentinel Kinetic MVHR series User manual

Vent-Axia

Vent-Axia Lo-Carbon Minivent B Assembly instructions

Vent-Axia

Vent-Axia VASF100BO Assembly instructions

Vent-Axia

Vent-Axia SDX100B Assembly instructions

Vent-Axia

Vent-Axia ATQ20012D Assembly instructions

Vent-Axia

Vent-Axia T-Series Assembly Instructions

Vent-Axia

Vent-Axia SOLO Plus SELV Assembly instructions

Vent-Axia

Vent-Axia Lo-Carbon NBR dMEV C Assembly instructions

Vent-Axia

Vent-Axia NBR HTP 473809 Assembly instructions

Vent-Axia

Vent-Axia Sentinel Kinetic V Guide

Vent-Axia

Vent-Axia HR400 User guide

Vent-Axia

Vent-Axia SDX EC Series Assembly instructions

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual