Vanco Evolution EVEX2005 User manual
HDMI
Transmitter
Connect Power Supply
QUICK INSTALL GUIDE
Factory Setting EDID & EQ Dial - From Factory Settings are as Follows:
1. Transmitter Factory Default Setting is Set at EDID = “0” Supporting: HD (1080p@60) (1080p@30) (1080p@24)
(1080i@60)(720p@60) - 24bit 2D video & 7.1ch audio
2. Receiver E.Q. Dial Setting = “4” Supporting: 20M-25Meters (66 ft to 82 ft)
3. Proceed to Connect & Operate with Normal Installation (see reverse side). If there is no handshake or signal, Adjust EQ
Gain Control according to your CAT5e/CAT6 Cabling: from Minimum Dial Setting “0” to Maximum Setting “7”
Manual EDID Learning Mode
1. Set Learning (Copy) EDID Mode on the Transmitter (TX) unit = “7”
2. (SEE DRAWING) FIRST: Connect Transmitter (TX) unit directly to the Flat Panel Display using a HDMI cable. SECOND:
Connect the 5VDC Power Adapter. The “yellow” Status LED light must blink once for Learning (Copy) EDID to be
Successful. Now you can disconnect Transmitter (TX) from Flat Panel Display.
Note - Do not connect Receiver ( RX) unit during Learning (Copy) EDID Mode
If experiencing No Picture, Picture Flashing, or Drop-Signal then proceed to Manual Learning EDID Mode
NOTE - Recommended EDID setting for most cable and satellite set top boxes is
EDID “4” or “5”. If no signal is displayed after manual EDID learning mode, adjust
to another EDID setting by doing the following:
1. Unplug the 5VDC power supply and HDMI cable from the Transmitter (TX)
2. Adjust EDID to desired setting
3. Reconnect HDMI cable from the source into the Transmitter (TX)
4. Reconnect 5VDC power supply to the Transmitter (TX)
3. Change Transmitter back to Factory Default Setting EDID = “0”
4. Proceed to Connect & Operate with Normal Installation (see reverse side). Wait for Sync
Lights (on Transmitter & Receiver) to Stop Flashing
5. If no Picture or Signal is on the Flat Panel Display then Power OFF (both Units) & Power
ON (both Units). Simply remove the 5VDC Power supplies & reconnect
BluRay® Player
HDTV
HDMI HDMI
IR Transmitter IR Receiver
IR Transmitter
IR
Receiver
HDMI over Cat5e/6
Transmitter Receiver
Back
Front
Back
Front
1. Connect a source such as a Blu-Ray Player, game
console, A/V Receiver, Cable or Satellite Receiver, etc.
to the HDMI input on the Transmitting unit.
2. Connect a display such as an HDTV or HD Projector to
the HDMI output on the Receiving unit.
3. Connect a single Category 5e/6 up to 131ft/40m to
the output of the Transmitting unit, and the other end to
the input of the Receiving unit.
4. For power, plug both the Transmitting unit and Receiving
unit with the included power supplies.
CONNECT AND OPERATE
0 - EDID Full-HD (1080p@60) (1080p@30) (1080p@24)
(1080i@60 (720p@60) - 24bit 2D video & 7.1ch audio
1 - EDID Full-HD(1080p@60) - 24bit 2D video & 2ch audio
2 - EDID Full-HD(1080p@60) - 24bit 3D video & 7.1ch audio
3 - EDID Full-HD(1080p@60) - 24bit 3D video & 2ch audio
4 - EDID HD(1080p@30)(1080i@60)(720p@60) - 24bit 2D video
& 7.1ch audio
5 - EDID HD(1080p@30)(1080i@60)(720p@60) - 24bit 2D video
& 2ch audio
6 - EDID Full-HD(1080p@60) - 36bit 2D video & 7.1ch audio
7 - Auto EDID learning/ Manual EDID learning mode
EQ ROTARY DIAL
If you see ickering or blinking image on the display, adjust the EQ rotary
switch to improve the cable skew. MAX stands for the strongest HDMI
signal level for the longest possible transmission length while MIN stands
for the weakest HDMI signal level for short transmission length. Adjust the
signal level from MIN to MAX until desired video quality is displayed.
Recommended EQ settings
LENGTH
Position Cable Length
0 (MIN)-2 under 15m (49.5ft)
3-5 15-30m (49.5 ft - 99ft)
6-7 (MAX) 30-40m (99ft - 132ft)
EDID SETTINGS
Other manuals for Evolution EVEX2005
1
Table of contents
Other Vanco Extender manuals
Vanco
Vanco Evolution EVEX2330 User manual
Vanco
Vanco HDEX60 User manual
Vanco
Vanco Evolution EVEXHDB3 User manual
Vanco
Vanco IR-EXPKIT User manual
Vanco
Vanco EVEXHDB2 User manual
Vanco
Vanco VPW-280577 User manual
Vanco
Vanco Evolution EVMX44VW User manual
Vanco
Vanco Evolution EV4K2006 User manual
Vanco
Vanco Evolution EVEXHDB1 User manual
Vanco
Vanco EVOLUTION EVEXUSB2 User manual
Vanco
Vanco Evolution EVEV4K70 User manual
Vanco
Vanco EVEXHDARC User manual
Vanco
Vanco HDMIEX50 User manual
Vanco
Vanco Evolution EV4KWHDMI User manual
Vanco
Vanco Evolution User manual
Vanco
Vanco Evolution EVEXKVM2 User manual
Vanco
Vanco Evolution EVEXKVM1 User manual
Vanco
Vanco Evolution EVWP2006 User manual
Vanco
Vanco EVOLUTION EV4K2004 Instruction manual
Vanco
Vanco 280332 User manual
