Uplus Lighting 4020 IP User manual

User manual

4020 IP

Please read the instructions carefully before use

TABLE OF CONTENTS

1. Safety Instructions……………………………………………………………………………3-4

Technical Specifications………………………………………………………………………4

Control Menu ……………………………………………………………………………………5-6

DMX Channels ……………………………………………………………………………………6

Trouble Shooting…………………………………………………………………………………7

Fixture Cleaning………………………………………………………… ………………………7

STATEMENT

The product has well capability and intact packing when leave factory. All of the user should

comply with warning item and manual, any misuse cause of the damages are not included in our

guarantee, and also can not be responsible for any malfunction & problem owing to ignore the

manual.

1.Safety Instructions

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that

they also receive this instruction booklet.

•Unpack and check carefully there is no transportation damage before using the unit.

•Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

•It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

•The unit is for indoor use only. Use only in a dry location.

•The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces. Be sure that no ventilation slots are blocked.

•Disconnect main power before replacement or servicing.

•Make sure there are no flammable materials close to the unit while operating as it is fire hazard.

•Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always

by taking its base.

•Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher

than this Unit surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand

during its operation. Turn off the power and allow about 15 minutes for the unit to cool down before

replacing or serving.

•the event of serious operating problem, stop using the unit immediately.Never try to repair the unit

by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please

contact the nearest authorized technical assistance center. Always use the same type spare parts.

•DO NOT touch any wire during operation as high voltage might be causing electric shock.

Warning:

•To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.

•The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.

Caution:

•There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any

repairs yourself. In the unlikely event your unit may require service, please contact your nearest

dealer.

Installation:

•The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly

fixed to avoid vibration and slipping while operating. And make sure that the structure to which you

are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Also

always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture.

•The equipment must be fixed by professionals. And it must be fixed at a place where is out of the

touch of people.

2.Technical Specificationst

Operating Conditions

Mains voltage: 100-240V AC / 50-60Hz

Power: 800W

Beam andle:25°（15°/45°/60°optional)

Light source:40x20w RGBW 4in1 LED

IP Rating:IP65

Lifespan:around 100,000hours

Control:DMX512,4/6/9CH

Control Mode:DMX,Auto,Master,Slave mode

Dimmer:0-100%

Strobe：0-20HZ

Housing: Die-casting aluminum, powder-coated finish

Display: LCD color display with 4 touch buttons

NW：17KG

3.Control Menu

Display:

MENU To select the programming functions (press to unlock screen)

DOWN To go backward in the selected functions

UP To go forward in the selected functions

ENTER To confirm the selected functions

Set DMX Address:

1. Press "MENU" to unlock screen, then select the “DMX Address” and press "ENTER".

2. Showing "Set DMX Address 001", Press the "UP or DOWN" key to increase or decrease the

DMX address value.

Press "ENTER" to save and Exit, Press "Cancel" does not save and Exit

Main Menu

Sub-Menu1

Sub-Menu

Instruction

Address

001-512

DMX addr es s,

001-512

Manu al

Red

000-255

Red Brig ht ness

000-255

Green

000-255

Green Brightnes s

000-255

Blue

000-255

Blue Br ightness

000-255

White

000-255

Whit e Brig ht ness

000-255

Dimm er

000-255

Dimm er,000-255

Strobe

000-255

Strobe, speed 000-255

Au to

7 color

000-099

7 colors cha nge

7 fade

000-099

7 colors fade

7 br eathe

000-099

7 color pulse

Strobe 1

000-099

St robe 1

Strobe 2

000-099

St robe 2

Se tting

DM X

Pe rso n

4C H/6C

9C H

Channel mode: 4CH

/6CH/9CH

Dis play

INV

Di splay Inverse ON

OF F

Di splay Inverse OFF

Ba ck light

OP EN

Ba ck light keep

opening

30S

Ba ck light 30S OFF

60S

Ba ck light 60S OFF

4.DMX Channels

4/6/9 Channel mode

Dim mer

Mode

DI M1

Di mmer mo de 1

DI M2

Di mmer mo de 2

DI M3

Di mmer mo de 3

DI M4

Di mmer mo de 4

Fan Mode

AU TO

Fan Au to

HI GH

Fan high spe ed

LO W

Fan low speed

KEY Loc k

OF F

Ke y Lock OF F

Ke y Loc k ON, Aft er

turn ON this fun ction,

enter the pas sword UP

DOWN UP DOW N UP

DOWN UP DOW N th en

pr ess EN TER to enable

key operation

De fau lt

Factory Reset NO

YE S

Factory Reset YES

Lang uage

En glish

Language English

Ch inese

Language Chinese

In fo

VER:02

So ftw are version

RUN TI ME

Ru nning time

Function

Value

Instruction

Dimmer

0-255

Dimmer, from dark to bright

Strobe

0-12

No function

13-255

Strobe from slow to fast

Red Dimming

0-255

Red Dimming, from dark to bright

Green

Dimming

0-255

Green Dimming, from dark to bright

Blue Dimming

0-255

Blue Dimming, from dark to bright

White

Dimming

0-255

White Dimming, from dark to bright

Color

Selection

0-31

No function

32-63

Red

64-95

Green

96-127

Blue

128-159

White

160-191

Red+Green

192-223

Red+Blue

224-255

Green+Blue

Macro

Function

0-50

No function

101-150

Color Change

151-200

Color Gradual

201-255

Color Pulse

Speed

0-255

Speed from slow to fast

5.Trouble Shooting

ollo

ing

few

oble

y occu

uring

ope

tion

. He

tion

leshooting

The

does

work

, no

ght

Check

nect

ion of p

owe

eas

ure

ins

volt

Check

pow

LED

responding

LED

on.

che

nectors,

link

ope

If th

nd no

espons

el,

che

ess

etti

s a

ity

nter

ittent

oble

che

ins

onn

ecto

PCB

nit

the

iou

ntroller

Check

or run

lon

volta

les

terfer

ence

inter

face

circui

. One

the

cha

ing

tep

moto

dam

the

nect

to th

PCB

oken.

oto

’

ive

PCB

ndition

6.Fixture Cleaning

The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to

optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp,

smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics.

Clean with soft cloth using normal glass cleaning fluid.

Always dry the parts carefully.

Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.

Table of contents

Other Uplus Lighting Lighting Equipment manuals

Uplus Lighting

Uplus Lighting RETRO 360 User manual

Uplus Lighting

Uplus Lighting IP-L360 User manual

Uplus Lighting

Uplus Lighting 460LED BSW User manual

Uplus Lighting

Uplus Lighting 37X15ZWASH User manual

Uplus Lighting

Uplus Lighting IR 1210 PAR User manual

Uplus Lighting

Uplus Lighting 200 BLINDER User manual

Uplus Lighting

Uplus Lighting IP MATRIX 5 User manual

Uplus Lighting

Uplus Lighting 150COBPAR User manual

Uplus Lighting

Uplus Lighting 200 LED BSW User manual

Uplus Lighting

Uplus Lighting 10X30 COB BAR User manual

Uplus Lighting

Uplus Lighting PIXEL IP20X15 BAR User manual

Uplus Lighting

Uplus Lighting 360 BEAM User manual

Uplus Lighting

Uplus Lighting BSW 350 User manual

Uplus Lighting

Uplus Lighting LED PROFILE MZ User manual

Uplus Lighting

Uplus Lighting 400 IP BLINDER User manual

Uplus Lighting

Uplus Lighting COB400 ZOOM User manual

Uplus Lighting

Uplus Lighting MINI740 User manual

Uplus Lighting

Uplus Lighting DUAD540 STROBE User manual

Uplus Lighting

Uplus Lighting W3725 User manual

Uplus Lighting

Uplus Lighting 280 LED BSW User manual

Uplus Lighting

Uplus Lighting PF350 User manual

Uplus Lighting

Uplus Lighting 250 BEAM User manual

Uplus Lighting

Uplus Lighting 300 MZ-SPOT PR User manual

Uplus Lighting

Uplus Lighting IP1000 Strobe User manual

Popular Lighting Equipment manuals by other brands

Brizo

Brizo 8SP-MU-4 manual

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 installation instructions

IKEA

IKEA BJÖRKSPIREA manual

Laserworld

Laserworld Evolution Series ES-400RGB manual

Alien

Alien RG STAR user manual

EuroLite

EuroLite LED B-40 user manual

Qazqa

Qazqa Suplux SL 3 Black 103062 instruction manual

Commercial Electric

Commercial Electric 54568141 Use and care guide

CREE LIGHTING

CREE LIGHTING 304 Series installation instructions

Goobay

Goobay 49867 user manual

ECOMAN ITALIA

ECOMAN ITALIA LED T8 instruction manual

Alkalite

Alkalite Krypton KT-81 user manual

Clas Ohlson

Clas Ohlson GU10 manual

DTS

DTS DELTA 10 F user manual

ring

ring Solar Steplight manual

One Stop Gardens

One Stop Gardens 57696 Owner's manual & safety instructions

Chauvet DJ

Chauvet DJ COREpar UV120 ILS user manual

SIREM

SIREM Swimeo A2 instructions