Uplus Lighting 20 MINI SPOT User manual

User manual

20 MINI SPOT

Please read the instructions carefully before use

TABLE OF CONTENTS

1. Safety Instructions……………………………………………………………………………3

2.Technical Specifications………………………………………………………………………4

3.Descriptions………………………………………………………………………………………5

4.Unpacking…………………………………………………………………………………………5

5.Control Menu ……………………………………………………………………………………6-8

6.DMX Channels ……………………………………………………………………………………8

7.Dimension …………………………………………………………………………………………9

8.Trouble Shooting…………………………………………………………………………………10

9.Fixture Cleaning………………………………………………………… ………………………10

STATEMENT

The product has well capability and intact packing when leave factory. All of the user should

comply with warning item and manual, any misuse cause of the damages are not included in our

guarantee, and also can not be responsible for any malfunction & problem owing to ignore the

manual.

1.Safety Instructions

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they also

receive this instruction booklet.

•Unpack and check carefully there is no transportation damage before using the unit.

•Before operating, ensure that the voltage and frequency of power supply match the power requirements of the

unit.

•It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

•The unit is for indoor use only. Use only in a dry location.

•The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent surfaces. Be sure

that no ventilation slots are blocked.

•Disconnect main power before replacement or servicing.

•Make sure there are no flammable materials close to the unit while operating as it is fire hazard.

•Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always by taking its

base.

•Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher than this Unit

surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand during its operation. Turn off

the power and allow about 15 minutes for the unit to cool down before replacing or serving.

•the event of serious operating problem, stop using the unit immediately.Never try to repair the unit by yourself.

Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest

authorized technical assistance center. Always use the same type spare parts.

•DO NOT touch any wire during operation as high voltage might be causing electric shock.

Warning:

•To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.

•The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.

Caution:

•There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any repairs yourself.

In the unlikely event your unit may require service, please contact your nearest dealer.

Installation:

•The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed to

avoid vibration and slipping while operating. And make sure that the structure to which you are attaching the unit

is secure and is able to support a weight of 10 times of the unit’s weight. Also always use a safety cable that can

hold 12 times of the weight of the unit when installing the fixture.

•The equipment must be fixed by professionals. And it must be fixed at a place where is out of the touch of

people.

2.Technical Specifications

Light Source:

LED POWER: 20W

LED Color: single WW / CW

Color Rendering Index(CRI): Ra≥90

LED Life Time: over 50,000 hours

Power supply:

Voltage: AC100-240V

Max.power: 20W

Optics:

Fixed Lens: 19°/26°/36°/50°(optional)

Iris: optional

Color Frame: optional

Features:

Focus: Can be adjusted by hand

Light body: Die-casting Aluminum

Body color: Black / White

Feature of housing: Small volume, lightweight

Control:

Control Protocol: DMX

Control System: DMX, Auto run and Master/Slave

DMX Channels: 1/3CH

Working Environment :

Working Temperature: -30~40℃

Cooling System: Fan-less no noise

IP Grade: IP20

Package :

Dimensions: 269.75*122*122mm

Net Weight: 2.0kgs

Gross Weight: 2.5kgs

Packing size: 34*17*15cm (1pc/carton)

54*37*32cm (6pcs/carton)

3.Descriptions

·Ease of use, superior optics, crystal-clear image projection

·High-quality dimming, and even beam field

·available in four field angles: 19°, 26°, 36° and 50°

·With DMX control

·You can choose to have a track-mounted design

·No fan totally silent operation for use in studio and theatre applications

·Using for museums, retail outlets, restaurants, light labs, children's theaters, and other small scale installations

where size matters.

4.Unpacking

Thank you for choosing our 20 MINI SPOT. For your own safety, please read this manual before installing the

device. This manual covers the important information on installation and applications. Please install and operate

the fixture with following instructions. Meanwhile, please keep this manual well for future needs.

The 20 MINI SPOT is made of a new type of high temperature strength of die-casting aluminum with nice outlook.

The fixture is designed and manufactured strictly following CE standards, complying with international standard

DMX512 protocol. It's available independently controlled and link able with each other for operation. And it is

applicable for useum, Retail store, Restaurant, Children theater, Gallery.

The 20 MINI SPOT adopts 1PCS 20W COB LED (CW Or WW) which features high brightness and stability. Please

carefully unpack it when you receive the fixture and check whether it is damaged during the transportation. And

please check whether the following items are included inside the box:

5.Control Menu

Main key

【MENU】Main menu or back the last menu

【UP】Choosing data value

【DOWN】Choosing data value

【ENTER】Enter, choose the vice menu or end edit.

Combination key

Combination by 2 or more key. Such as “UP+DOWN” Press UP and DOWN at the same time.

Combination key of “UP+DOWN” is different from “UP” or “DOWN”, it have its own function.

Long press

Press the button for long time then leave.

LED show

English word/function

key operation

description

Advanced DMX

UP/DOWN key to choose the

address code (1~512)

ENTER key to save

check “channel

data”

Advance DMX controller state

dMX

normal DMX controller state

SLAve

equal“d001”

Above is the slave mode, attention:

1、Make sure there is only a signal (controller or master light)

2、The light will be turn off if the signal is cut down. (turn off the controller or master light)

Cool white

(0~255)ENTER to choose the led

group

UP/DOWN to choose the bright of

the led group

Change color

Strobe

UP/DOWN key to choose the speed

(1~50)

ENTER to save.

Strobe

Sound

Sound model

Above is the master state, the light will send the data automatically. (the slave light should

set “d001” or “SLAv”)

MENU UP DOWN ENTER

Current adjustment

Keyboard current adjustment

Under any main menu item, press and hold the MENU, after about 3 seconds to enter the

"keyboard current adjustment" mode, Then can adjust the current . Proceed as follows:

1、First see the "r030". "R" stands for red, so only red will be lit at this time, and the other colors

will turn off automatically. "030" represents the current current value, use the UP button or DOWN

button to adjust from 0 to 255. Note that the slow increase, suitable for this: If the current is too

large, will lead to lamp beads burned!

2、After adjusting the red, press the "MENU" key to switch to "G030" began to adjust the green,

the same time it will only light green while the other colors will automatically shut down ... ... The

adjustment of other colors and the like.

3、Press "ENTER" key to save and automatically return to "A001" menu

DMX Current regulation

Through the console (or host) for multiple lights current regulation. The console for example, the

following steps:

1、For reduce the risk of burning lamp. before the completion of step 3, please do not connect the

light to the console.

2、First of all through the "keyboard current adjustment" to adjust the ideal current value in a light

and record it.

3、Set the channels 1, 2, and 3 of the console to recorded the current values (to represent red,

green, and blue, for example,then set the channel 2 value to 100 for a green current value of 100).

This step must be completed before starting step 4! Otherwise it may be caused by channel value is

too large led lamp burning!

4、After confirming that step 3 is no problem,then connect the light to the console. Press and hold

the MENU key and ENTER key at the same time in any main menu. After about 3 seconds, enter

"DMX current adjustment" mode. The screen will display "CSdA"(Color Scale dMX Adjustment),and

which will flicker if the DMX signal is not received

5、Wait for about 1 second, if "CSdA" is not flicker then it has correctly received the current value

passed by the console (also can through lamp brightness to be observed), the adjustment is

successful.

4、Press "ENTER" key to save and automatically return to "A001" menu

6、In step 5, the channel value of the console can also be changed to adjust again. Since it is the

ideal value that has already been adjusted, generally do not need to adjust again. If you want to

adjust, you must be conscious, careful! If the current is too large, will lead to lamp burned!

Set Menu

In the “dEMo” menu, long press “ENTER” to set the menu.

Press MENU to change the menu option.

LED show

English Word/function

key operation

Description

LED waiting time

UP/DOWN choose the waiting time

0 = no screen protect

Screen protect time

High Power

UP/DOWN choose high power or not

On = 100%

off = 33.3%

Power choose

dMX-controller delay

UP/DOWN choose use the controller

delay or not

controller delay

Synchronization

UP/DOWN choose usemulti-light

synchronization or not

Multi-light

synchronization

LoAd

Long press ENTER until it shows

“LdEd”(loaded)

reset

rEturn

Press ENTER to save the data and

back to main menu.

Back to function menu

6.DMX Channels

Model – CH3

Channel

Data

Function

0~255

Dimmer

0~5

No function

6~255

Strobe: 6 is slowest, 255 is fastest

0~25

Turn on “delay by controller”

26~200

Turn off “delay by controller”

251~255

Sound mode: the changing of the light depends on the MIC of each light

Model – CH1

Channel

Data

Function

0~255

Dimmer

7.Dimension

Size of the fixture: 269(D)*122(W)*122(H)mm

8.Trouble Shooting

ollo

ing

few

oble

occu

uring

ope

tion

leshooting

The

does

work

ght

Check

nect

ion of p

owe

eas

ure

ins

volt

Check

pow

LED

responding

LED

on.

che

nectors,

link

ope

espons

el,

che

ess

etti

ity

nter

ittent

oble

che

ins

onn

ecto

PCB

nit

the

iou

ntroller

Check

or run

lon

volta

les

terfer

ence

inter

face

circui

One

the

cha

ing

tep

moto

dam

the

nect

PCB

oken.

oto

’

ive

PCB

ndition

9.Fixture Cleaning

The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to

optimize light output. Cleaning frequency depends on the environment in which the fixture operates:

damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics.

Clean with soft cloth using normal glass cleaning fluid.

Always dry the parts carefully.

Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.

Table of contents

Other Uplus Lighting Lighting Equipment manuals

Uplus Lighting

Uplus Lighting 200 LED BSW User manual

Uplus Lighting

Uplus Lighting LED PROFILE FIX User manual

Uplus Lighting

Uplus Lighting 6 EYE RETRO BAR User manual

Uplus Lighting

Uplus Lighting 750 BSWF User manual

Uplus Lighting

Uplus Lighting IP MATRIX 5 User manual

Uplus Lighting

Uplus Lighting 230 BEAM User manual

Uplus Lighting

Uplus Lighting BAR 6 LASER User manual

Uplus Lighting

Uplus Lighting PF350 User manual

Uplus Lighting

Uplus Lighting IP-Z740 User manual

Uplus Lighting

Uplus Lighting 200 MZ-SPOT PR User manual

Uplus Lighting

Uplus Lighting 250 LED BEAM User manual

Uplus Lighting

Uplus Lighting BSW 350 User manual

Uplus Lighting

Uplus Lighting RETRO 360 User manual

Uplus Lighting

Uplus Lighting 400 IP BLINDER User manual

Uplus Lighting

Uplus Lighting LED PROFILE MZ User manual

Uplus Lighting

Uplus Lighting COB400 ZOOM User manual

Uplus Lighting

Uplus Lighting IP-L360 User manual

Uplus Lighting

Uplus Lighting MIX560 User manual

Uplus Lighting

Uplus Lighting 3010 IP PAR User manual

Uplus Lighting

Uplus Lighting BR360 User manual

Uplus Lighting

Uplus Lighting DUAD540 STROBE User manual

Uplus Lighting

Uplus Lighting IP 300Z SPOT-WW User manual

Uplus Lighting

Uplus Lighting 200 BLINDER User manual

Uplus Lighting

Uplus Lighting IP1000 Strobe User manual

Popular Lighting Equipment manuals by other brands

Brizo

Brizo 8SP-MU-4 manual

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 installation instructions

IKEA

IKEA BJÖRKSPIREA manual

Laserworld

Laserworld Evolution Series ES-400RGB manual

Alien

Alien RG STAR user manual

EuroLite

EuroLite LED B-40 user manual

Qazqa

Qazqa Suplux SL 3 Black 103062 instruction manual

Commercial Electric

Commercial Electric 54568141 Use and care guide

CREE LIGHTING

CREE LIGHTING 304 Series installation instructions

Goobay

Goobay 49867 user manual

ECOMAN ITALIA

ECOMAN ITALIA LED T8 instruction manual

Alkalite

Alkalite Krypton KT-81 user manual

Clas Ohlson

Clas Ohlson GU10 manual

DTS

DTS DELTA 10 F user manual

ring

ring Solar Steplight manual

One Stop Gardens

One Stop Gardens 57696 Owner's manual & safety instructions

Chauvet DJ

Chauvet DJ COREpar UV120 ILS user manual

SIREM

SIREM Swimeo A2 instructions