Unitech EA520 User manual
EA520 Vehicle Cradle
Quick Start Guide
609574G V1.0
Package
Please make sure the following contents are in the
EA520 vehicle cradle gift box.
If something is missing or damaged, please contact
your Unitech representative.
• EA520 Vehicle Cradle
• USB Type-C Cable (power input: 5V/2A)
*Note: The package does not include USB car charger
(cigarette charger). Please apply the car charger with
power output 5V/2A to match with EA520 vehicle cradle.
The Package Contents
Install EA520 into the Vehicle Cradle
Insert the Attached Cover into the Cradle
Optional Accessories
• Attached Cover (for EA520 without boot case)
• HD AMPs Bracket with 26mm Ball Joint Part
(with AMPs screws)
• Dashboard Mount Only
• HD AMPs Mount
Product View
Charging port
Insert EA520 from top to bottom until it reach the bottom.
Put the attached cover into the cradle and make
sure the arrows of the attached cover are pointing
upward and match with the cradle.
How to use the Vehicle Cradle
•Insert EA520 with boot case into the vehicle cradle
directly.
* It is suggested to charge EA520 without boot case
after putting the attached cover into the vehicle
cradle to prevent noise while shaking. The attached
cover is optional for securing EA520 without the boot
case more firmly.
• To ensure the unit working properly, please keep all
connectors away from the contaminants staying inside
of them such as dust, grease, mud, and water.
The negligence may cause the unit with no communication,
short circuited, overheated and so on.
• If the connector is damaged, please ensure the connector is
being fully repaired before using the unit to avoid causing
short circuited.
CAUTION!
Copyright 2022 Unitech Electronics Co., Ltd. All rights reserved.
Unitech is a registered trademark of Unitech Electronics Co., Ltd.
http://www.ute.com/
Remap the Volume Key
How to Remove Wearable Kit
Charging through Vehicle Cradle
Connect one end of the USB Type-C cable to the USB
port on EA520 vehicle cradle, and the other end to
USB car charger (cigarette charger).
The power key is not accessible while EA520 is in
the vehicle cradle, so it's suggest to “remapping” the
volume key to wake up the screen. Please follow the
directions below to remap the volume key to wake
up screen.
1. Enter StageGo from the Apps.
2. Scan the barcode on the right.
Note:This barcode is designated to be scanned by
StageGo. Scanning through USS is not effective.
3. The screen will show as below.
The number of success is “1”, meaning you have
successfully finish key remap setting.
Type-C
Go back to Original Setting
1. Click on KeyRemap in the Apps.
2. Click on VOLUME_UP.
3. Select Action, then select Default key: VOLUME_UP.
Other manuals for EA520
7
Other Unitech PDA manuals
Unitech
Unitech PA820 User manual
Unitech
Unitech PA500 User manual
Unitech
Unitech PA968 User manual
Unitech
Unitech PA600 User manual
Unitech
Unitech PA500 User manual
Unitech
Unitech PA500 User manual
Unitech
Unitech PA970 User manual
Unitech
Unitech PA500II User manual
Unitech
Unitech PA690 User manual
Unitech
Unitech EA502 User manual
Unitech
Unitech PA500 Owner's manual
Unitech
Unitech RH767 User manual
Unitech
Unitech RH767 User manual
Unitech
Unitech HT580 User manual
Unitech
Unitech PA962 User manual
Unitech
Unitech EA320 User manual
Unitech
Unitech PA600 User manual
Unitech
Unitech PA962 User manual
Unitech
Unitech PA700 Series User manual
Unitech
Unitech PA970 User manual
