Unitech PA692A User manual
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co., Ltd.
Rugged Handheld Computer
- PA692A -
User's Manual
Version 1.1
Table of Contents
(QJOLVK
'HXWVFK
(VSDQRO
)UDQFDLV
7XUNFH
㖍㛔婆
㔯䷩橼
㔯ㆰփ««««««««««««««««««««««««««
1
1. Package
English
Please make sure the following contents are in the PA692A gift box.
If something is missing or damaged, please contact your unitech
representative.
Deutsch
The standard package contents
PA692A Terminal
Battery
Plugs + Power Adapter
Hand Strap
USB cable
Regulatory Compliance Statements
Optional accessory:
Vehicle Cradle (Car Kit)
Single slot USB Cradle
RS232 cable
Single Slot Ethernet cradle.
4 slot Multi-Bay Ethernet Cradle
4 slot battery charger
Gun grip
Earphone
Espanol Francais ѝ᮷ㆰփύЎ(ᕷᡏ)
2
English Deutsch Espanol Francais ѝ᮷ㆰփύЎ(ᕷᡏ)
8
1
3
2
5
4
1
2. Product Detail
PA692A Front and Rear View
13
1
7
8
9
10
11
12
13
6
LED indicators 8 Battery cover
2 LCD touch screen 9 Antenna
3 Keypads 10 Speaker
4 Receiver 11 5 megapixel / AF camera
5 Universal connector 12 LED flash light
6 Barcode scanner window 13 Battery cover tab
7 Earphone jack
PA692A Left and Right View
3
English Deutsch Espanol Francais ѝ᮷ㆰփύЎ(ᕷᡏ)
4
1
5
3
2
1 Scanner trigger button 4 Camera mode
2 Volume up/down 5 MicroSD card slot
3 Vibration/Mute mode
3. Getting Started
Installing the Battery
English
A backup battery cell is embedded into your device to prevent data loss when
the main battery pack is removed or completely discharged. This backup
battery will keep the data and system setting for up to 2 hours if the main
battery is removed.
Deutsch
1. Open the battery cover by sliding
the tabs on both sides in the
direction of the arrows shown and
lift the cover up.
Battery Cover Tab
Espanol
2. Push up the backup battery and
switch to the “ON” position by
using any tip of a pen to turn on
the backup battery.
4
Francais ѝ᮷ㆰփύЎ(ᕷᡏ)
3. Slide and position the battery
pack, making sure the battery
contacts are aligned with the
contacts in the compartment.
4. Use your thumb to snap the
battery in place.
5. Replace the battery cover by
pushing down on the tabs and
sliding them back into place as
shown.
Backup
Battery
Switch
Battery
Compartment
Contacts
Plastic Tab
5
English Deutsch Espanol Francais ѝ᮷ㆰփύЎ(ᕷᡏ)
NOTE: Make sure the battery cover is securely closed, or you may be unable to
turn ON the terminal.
NOTE: To enable the backup battery cell to provide backup power supply, charge your device
with the main battery pack for at least 24 hours.
NOTE: To power on the device properly, make sure to replace the battery cover
after installing the battery.
WARNING! There is a risk of fire and burns if the battery pack is handled improperly. DO
NOT disassemble, crush, puncture, short external contacts, or dispose the
battery pack in fire or water. DO NOT attempt to open or service the battery pack.
Dispose of used batteries according to local recycling guidelines in your area.
Charging the Battery
Before using the terminal for the first time, you need to charge it for about 24
hours. After that, you can charge the terminal for 3 hours to recharge the
battery to full capacity. Charge the terminal using the USB charging cable or
the docking station.
English
1. Press and hold the release button on both sides of the USB charging
cable and connect it to the PA692A
2. Plug the AC adapter cable into the power jack of the USB charging cable
3. Plug the AC adapter cord into an electrical outlet.
Deutsch
WARNING! Turn ON the backup battery switch before charging the battery.
Data you entered may not be properly stored until the built-in backup battery has
been adequately charged.
Espanol Francais ѝ᮷ㆰփύЎ(ᕷᡏ)
6
Turning on the terminal for the first time
After you have initially charged your device for about 24 hours, the device is
ready to be used. You can now start up your device. You can then set up the
languages, WiFi setting and date and time.
Power-On Button
Turn ON your device by pressing the power button on the front panel.
English Deutsch
Checking the LED status
Terminal LED indicators
Espanol
7
Francais
Status LED Description
Scan Green light blinks once Successful reading
Solid Red light Being charged
Terminal Power Solid Green light Fully charged
ѝ᮷ㆰփ
Checking the Battery Status
If the battery level becomes low in the course of normal use, a status icon
appears on the device screen indicating low or very low battery status. In both
cases, connect PC with USB to back up your data, and then recharge your
device as soon as possible.
ύЎ(ᕷᡏ)
Using the MicroSD Memory Card
The PA692A has an expansion slot compatible with a range of MicroSD
memory cards, which are primarily used to back up or transfer files and data.
English
Inserting a Memory Card
1. Remove the two screws on the
MicroSD slot shield and remove
the shield.
Deutsch
2. Insert the MicroSD card with the
notched corner as shown.
Espanol
3. Push the card into the slot until you feel the MicroSD card click into place.
4. Screw the MicroSD compartment cover back into place.
Francais
Removing the Memory Card
1. Remove the two screws from the MicroSD compartment shield and
remove the shield.
2. Press the card in and release. The card pops out.
ѝ᮷ㆰփ
3. Remove the card from the slot.
ύЎ(ᕷᡏ)
8
Other manuals for PA692A
1
Table of contents
Languages:
Other Unitech Handheld manuals
Unitech
Unitech PA970 User manual
Unitech
Unitech HT1 1D Batch User manual
Unitech
Unitech HT630 Installation and operation manual
Unitech
Unitech PA950 User manual
Unitech
Unitech PA968 User manual
Unitech
Unitech SRD650 User manual
Unitech
Unitech PA968 User manual
Unitech
Unitech HT660e User manual
Unitech
Unitech HT580 User manual
Unitech
Unitech HT 1 User manual
Unitech
Unitech PA968 User manual
Unitech
Unitech PT600 User manual
Unitech
Unitech PA600 II Standard User manual
Unitech
Unitech HT630 Instruction manual
Unitech
Unitech PA400 User manual
Unitech
Unitech HT730 User manual
Unitech
Unitech HT580L User manual
Unitech
Unitech PA520 User manual
Unitech
Unitech PA600 User manual
Unitech
Unitech HT630 User manual
