Unitech MS836 User manual

Barcode Scanner

User Manual

MS836

V1.0

... 17

........... 19

............ 28

CONTENTS

...............................................

................................

......................

.....................................

.............................................

.........................................

.....................................

...........................................

.....................................

......................................

.........................................

...............................

.............................

....................

..............................

......................................

.......................................

....................................

...............................

.................

....................

...........................

.........................................

...............................................

120

.........................................

124

sales of this manual are forbidden without our

company permission.

Responsibility Clause

We are not responsibility for errors,omissions and

variation without notice.

Chapter

1 System Setting

Enable/Disable Barcode Programming

Scanning the Enter Setup/Exit Setup barcode can

enable barcode programming. After barcode

programming is enabled, you can scan a number of

programming barcodes to configure your scanner.

Barcode programming is on by default.

In real application, programming barcodes hardly

progr

is unnecessary to disable programming each

time you finishthe configuration.

Programming Barcode Data

W010F01

W010F00

*Enter Setup

Exit Setup

W060F06

W060F00

Transmit Programming

Barcode Data

*Do Not Transmit

Programming Barcode Data

Factory Defaults

Scanning the following barcode can restore

the scanner to the factory defaults.

You may need to reset your scanner when:

scanner is not properly configured so that it

fails to decode barcodes;

you forget previous configuration and want

to avoid its impact;

functions that are rarely used have been

enabled for the time being.

WFFD980

Restore All Factory

Defaults

Scan Mode

Manual Mode:A trigger pull activates a decode

session. The decode session continues until the

barcode is decoded or the trigger is released or the

decode session timeout expires.

*Manual Mode

W030000

Decode Session Timeout: This parameter sets the

maximum time decode session continues during a

scan attempt. It is programmable in 1s increments

from 1s to 255s. The default timeout is 15s. If the

parameter is set to 0, the decode session timeout is

infinite.

Decode Session Timeout

M00031D

Example: Set the decode session timeout to 5s

Scan the Enter Setup barcode.

Scan the Decode Session Timeout barcode.

3. S

num

“

”.

(

e D

igi

Barcodes section in Appendix)

Scan the Save barcode. (See the Save/Cancel

Barcodes section in Appendix)

Scan the Exit Setup barcode.

Continuous Mode

Continuous Mode: A trigger press activates the

scanner to scan and decode at user-specified

intervals, i.e. the timeout between decodes. Each

decode session lasts until barcode is decoded or

the decode session timeout expires. To

suspend/resume the operation, simply press

the trigger. By default, the scanner rereads

same barcode with no delay.

Continuous Mode

W030002

Decode Session Timeout: This parameter sets the

maximum time decode session continues during a

scan attempt. It is programmable in 1s increments

from 1s to 255s. The default timeout is 15s. If the

parameter is set to 0, the decode session timeout is

infinite.

Decode Session Timeout

M00031D

Example: Set the decode session timeout to 5s

Scan the Enter Setup barcode.

Scan the Decode Session Timeout barcode.

3. S

num

“

”.

(

e D

igi

Barcodes section in Appendix)

Scan the Save barcode. (See the Save/Cancel

Barcodes section in Appendix)

Scan the Exit Setup barcode.

Timeout between Decodes:This parameter sets

the timeout between decode sessions. When a

decode session ends, next session will not

happen until the timeout between decodes

expires. It is programmable in 0.1s increments

from 0.0s to 25.5s. The default timeout is 1.0s.

Timeout between Decodes

M00031C

Example: Set the timeout between decodes to 5s

Scan the Enter Setup barcode.

Scan the Timeout between Decodes barcode.

3. S

num

“

”

“

”.

(SeetheDigitBarcodessectionin Appendix)

Scan the Save barcode. (See the Save/Cancel

Barcodes section in Appendix)

Scan the Exit Setup barcode.

Reread Delay sets the time period before the

scanner can read the same barcode a second time.

It protects against accidental rereads of the

same barcode. This parameter is programmable

in 0.1s increments from 0.1s to 25.5s. The default

delay is 3.0s. If the parameter is set to 0, the delay

is infinite.

Note: This parameter only applies when the Reread

Same Barcode with a Delay is enabled.

Reread Delay

M00031E

W100A00

*Reread Same Barcode

with No Delay

W100A10

Reread Same Barcode

with a Delay

Example: Set the reread delay to 5s

Scan the Enter Setup barcode.

Scan the Reread Delay barcode.

3. S

num

“

”

“

”.

(SeetheDigitBarcodessectionin Appendix)

Scan the Save barcode. (See the Save/Cancel

Barcodes section in Appendix)

Scan the Exit Setup barcode.

Sense Mode

Sense Mode: The scanner activates a decode

session every time when it detects a change in

ambient illumination and meets the requirement of

the image stabilization timeout. Decode session

continues until barcode is decoded or the decode

session timeout expires. A trigger pull can also

activate a decode session. By default, the scanner

rereads same barcode with no delay.

Sense Mode

W030003

Decode Session Timeout: This parameter sets the

maximum time decode session continues during a scan

attempt. It is programmable in 1s increments from 1s to

255s. The default timeout is 15s. If the parameter is set to

0, the decode session timeout is infinite.

M00031D

Decode Session Timeout

Example: Set the decode session timeout to 5s

Scan the Enter Setup barcode.

Scan the Decode Session Timeout barcode.

3. S

num

“

”.

(

e D

igi

Barcodes section in Appendix)

Scan the Save barcode. (See the Save/Cancel

Barcodes section in Appendix)

Scan the Exit Setup barcode.

Other manuals for MS836

Table of contents

Unitech MS836 User manual

Popular Barcode Reader manuals by other brands