Ubiquiti EdgePoint EP-S16 User manual

EdgePoint Switch Wall-Mount Bracket Metal Straps (Qty. 2)

Cable Sleeve Cable Ties (Qty. 20) S2 Hex Wrench

Wall-Mount Screws (Qty. 4) Wall-Mount Anchors (Qty. 4) Phillips Bolts (Qty. 2)

Gigabit PoE (54V, 1.5A) with

Mounting Bracket Power Cord PoE Screws (Qty. 2)

Package Contents

EP-S16 Quick Start Guide

PoE Anchors (Qty. 2)

Installation Requirements

7 mm socket wrench

S2 hex wrench

Ground wire – min. 10 AWG (5 mm ) and max. length: 1 m. As a safety precaution, ground

the EdgePoint to a grounded mast, pole, tower, or grounding bar.

Shielded Category 5 (or above) cabling should be used for all wired Ethernet connections

and should be grounded through the AC ground of the PoE.

We recommend that you protect your networks from harmful outdoor environments and

destructive ESD events with industrial-grade, shielded Ethernet cable from Ubiquiti. For

more details, visit:

ui.com/toughcable

Power Options

Either the VDC or PoE input type is used at any one time. If both are connected, only the input

type with the highest voltage will be used; the other can be used as a backup.

Both PoE inputs can be used at the same time. If there is a voltage diﬀerence, the higher-

voltage source will be used rst. The voltage from the initial source will drop as the load

increases. When the voltage drops to the same level as the lower-voltage source, then the

lower-voltage source will also start providing power.

Power Input Options

54VDC, 6A

54V, 1.5A on PoE In/1

54V, 1.5A on PoE In/2

Power Output Options

EdgePoint (required)

Passive 54/24V, 4-Pair PoE on 1-4

PoE+ or Passive 24V, 2-Pair PoE on 5-16

The number of devices that can be powered depends on the power consumption of the

specic devices and the power input option. Example: If you provide 54VDC, 1.5A, then you

have 81W of power. If the EdgePoint uses 40W (Max. Power Consumption), then you have

41W available for passive PoE output. Check product specications for the power

consumption values to use in your calculations.

Hardware Overview

EP-S16 Quick Start Guide

Reset Button

Console Port

DC Input

Ports PoE In / 1 - 2 (54/24V PoE Out)

Ports 3 - 4 (54/24V PoE Out)

Ports 5 - 16 (PoE+ or 24V PoE Out)

SFP+ 1 - 2 Ports

Click here

to learn how to reset the EdgePoint to factory defaults.

RJ45 serial console port for Command Line Interface (CLI) management.

Note:

Remove the protective plug from the Console port before use.

Terminal block connector uses auto-polarity detection and accepts +42 to +56VDC, 6A

input (including the Ubiquiti EdgePower™, model EP-54V-150W) to power the EdgePoint

and passive PoE output. -48V is NOT supported.

RJ45 ports support 10/100/1000 Ethernet connections and have PoE input or output

functionality:

PoE Input

Accepts 54V, 1.5A PoE input to power the EdgePoint and PoE output.

PoE Output

You can congure the ports for 54/24V 4-pair PoE output.

Do NOT congure port PoE In / 1 or 2 in PoE output mode if you are using it as a PoE input

power source.

RJ45 ports support 10/100/1000 Ethernet connections and passive 54/24V, 4-pair PoE

output for airFiber® devices.

RJ45 ports support 10/100/1000 Ethernet connections and PoE+ (IEEE 802.3af/802.3at) or

passive 24V, 2-pair PoE output for airMAX® or other devices.

SFP+ ports are hot-swappable and support 1/10 Gbps ber SFP/SFP+ modules.

Note:

For extreme temperatures, please use industrial-grade ber SFP/SFP+

modules.

EP-S16 Quick Start Guide

System LED

EP-S16 Quick Start Guide

Speed/Link/Activity LED (Ports 1 - 16)

PoE Input LED (Ports 1 - 2)

PoE Output LED (Ports 1 - 4)

PoE Output LED (Ports 5 - 16)

Speed/Link/Activity (SFP+ 1 - 2 Ports)

Note:

The System LED functionality has been updated with rmware v1.8.0. We

recommend that you update the device to the latest rmware.

Flashing White Bootup in progress.

White Ready for use, not connected to Ubiquiti® Network

Management System (UNMS™). See

"UNMS

Management"

Blue Ready for use, connected to UNMS.

Steady Blue with Occasional

Flashing Ready for use, unable to connect to UNMS, check

connection to UNMS server.

Quickly Flashing Blue Used to locate a device in UNMS.

Alternating Blue/White Firmware upgrade in progress.

Oﬀ No Link

Amber 10/100 Mbps Link

Flashing Indicates Activity

Green 1000 Mbps (1 Gbps) Link

Flashing Indicates Activity

Oﬀ No PoE

Green 54V Passive

Oﬀ No PoE

Amber 54V Passive, 4-Pair

Green 24V Passive, 4-Pair

Oﬀ No PoE

Amber PoE+ Auto (IEEE 802.3af/802.3at)

Green 24V Passive, 2-Pair

EP-S16 Quick Start Guide

Lanyard Loop

Pole-Mount Bracket

PicoStation®M2HP Slot

Ground Bonding Point

Oﬀ No Link

Green 1000 Mbps (1 Gbps) Link

Flashing Indicates Activity

White 10 Gbps Link

Flashing Indicates Activity

Used for temporary support during installation.

Used for pole-mounting or in combination with the included Wall-Mount Bracket for wall-

mounting.

Used for mounting an optional PicoStationM2HP (not included) to the back of the

EdgePoint. (You can use the PicoStationM2HP for wireless management of the EdgePoint.)

Used to secure a ground wire (not included).

Attaching the Cable Sleeve

Note:

You have two options for using a 2.0-inch NPT (National Pipe Thread) male

conduit (not included):

Use the conduit instead of the Cable Sleeve.

Use the conduit to extend the Cable Sleeve.

Hardware Installation

EP-S16 Quick Start Guide

Mount the EdgePoint on a pole or to a wall:

"Pole-Mounting"

"Wall-Mounting"

Pole-Mounting

EP-S16 Quick Start Guide

3. Proceed to

"Grounding the EdgePoint"

Wall-Mounting

Note: The Wall-Mount Bracket must be anchored directly to a stud or other

structurally stable surface.

EP-S16 Quick Start Guide

Grounding the EdgePoint

EP-S16 Quick Start Guide

Connecting Ethernet



EP-S16 Quick Start Guide

Other Ubiquiti Switch manuals

Ubiquiti

Ubiquiti TouchSwitch Poe TS-5-POE User manual

Ubiquiti

Ubiquiti UniFi US-8-60W User manual

Ubiquiti

Ubiquiti US-48 User manual

Ubiquiti

Ubiquiti UBNT-US-8-150W-US User manual

Ubiquiti

Ubiquiti UniFi USW-Pro-24-POE User manual

Ubiquiti

Ubiquiti unifi switch 8 User manual

Ubiquiti

Ubiquiti UniFi USW-Pro-48-POE User manual

Ubiquiti

Ubiquiti ES-10X User manual

Ubiquiti

Ubiquiti UniFi USW-24-POE User manual

Ubiquiti

Ubiquiti UniFi USW-Industrial User manual

Ubiquiti

Ubiquiti UniFi USW-16-POE User manual

Ubiquiti

Ubiquiti EdgeSwitch 5XP User manual

Ubiquiti

Ubiquiti ES-5XP User manual

Ubiquiti

Ubiquiti EdgeSwitch 5XP User manual

Ubiquiti

Ubiquiti EdgeSwitch ES-16-XG User manual

Ubiquiti

Ubiquiti US-XG-6POE User manual

Ubiquiti

Ubiquiti EdgeSwitch 10 XP User manual

Ubiquiti

Ubiquiti NanoSwitch N-SW User manual

Ubiquiti

Ubiquiti UniFi US-8-60W User manual

Ubiquiti

Ubiquiti UniFi USW-Pro-24-POE User manual

Ubiquiti

Ubiquiti UniFi Switch Flex User manual

Ubiquiti

Ubiquiti US-8-150W User manual

Ubiquiti

Ubiquiti UniFi US-8-60W User manual

Ubiquiti

Ubiquiti UniFi US-48-500W User manual

Popular Switch manuals by other brands

URC

URC Total Control MFS-8 installation manual

Azbil

Azbil HPQ-D11 user manual

Sony

Sony DFS-900M operating instructions

SICK

SICK i17S operating instructions

F&F

F&F SZR-277 quick start guide

Shure

Shure UAMS/BK user guide

Dräger

Dräger X-zone Switch Off Instructions for use

Asco

Asco Joucomatic 349 Series manual

BT Mini Hub user guide

D-Link

D-Link DES-1226G manual

Johnson Controls

Johnson Controls FS80-C installation instructions

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Configuration guide

MicroNet

MicroNet SP1200A user manual

Ruijie

Ruijie RG-PF2920 Series Hardware installation and reference guide

Altinex

Altinex DA1914SX user guide

MiLAN

MiLAN MIL-SM2401M user guide

RJM

RJM MASTERMIND PBC/6X user manual

Atlas

Atlas MMK-KVM8 owner's manual