U-tec Ultraloq UL3 User manual
Ultraloq UL3 Series
Fingerprint and Touchscreen Smart Lock
User Guide ( V2.1 )
Welcome
- 1 -
Ultraloq Terms & Policies
Before using all Ultraloq products, please read all applicable terms, rules, policies
and usage provisions found at www.u-tec.com/company/privacy. By using your
Ultraloq, you agree to be bound by the U-tec Privacy Policy.
Need Help?
For technical documents and information
Please visit www.u-tec.com/support
Email: [email protected]
www.u-tec.com/lock/ul3_2th/guide
Please watch our easy step by step operation video before attempting to operate
your Ultraloq UL3 Series Fingerprint and Touchscreen Smart Lock.
Operation Video
- 2 -
1.1 Exterior
1.2 Interior
Bluetooth LED Indicator
The LED light will show the Bluetooth status.
Reset Button
Used to reset the lock to factory default settings.
Battery Cover
Used to cover the batteries and product label.
1. Lock Parts
Touchscreen
Fingerprint Reader
Message Display Screen
Backup Key Hole
Restart Button
Battery Cover
Reset Button
Bluetooth LED Indicator
Touchscreen
Used to enter the code and unlock from the outside.
Fingerprint Reader
Used to verify your finger and unlock from the outside.
Message Display Screen
An OLED display with intuitive information will walk you through the whole operation.
Backup Key Hole
Used to insert the key to unlock from the outside.
Restart Button
Used to restart the process if the lock activation fails.
- Numbers Back Enter
0 9
- 3 -
2. Using Your Lock
Step 1. Touch the lock with the back of your hand or fingers to activate the lock.
Step 2. Enter the 4-8 digit code and press the Button to unlock.
Step 3. Rotate the handle to open the door.
①
Use a microfiber cloth and wipe across the fingerprint reader surface and the
touchscreen.
2.1 Clean the fingerprint reader and touchscreen
2.2 Open the door from the outside
Step 1. Place your finger on the Fingerprint Reader to unlock.
Step 2. Rotate the handle to open the door
②
User PIN code
Fingerprint
- 4 -
2.3 Open the door from the inside
③ Smartphone
· When you activate the lock and see the message “Low battery”, you should replace the batteries.
· Use 3 high-quality alkaline AA batteries for replacement.
· Please don’t use any rechargeable batteries.
Note: Lithium batteries may have a longer life, but when they begin to run outof battery, they drain
fast. U-tec doesn’t recommend them, as you will not have enought time to change them before
the lock becomes non-functional.
2.5 Replace the battery
Use your smartphone to unlock. Please refer to the guide in the U-tec App.
Note: All data will be erased if you reset the UL3 to factory default settings.
Step 1. Remove the Battery Cover.
Step 2. Use the Reset Needle and press the Reset Button for 3 seconds until you hear
one long beep and two short beeps. The message display will show No User
Step 3. If the UL3 is paired with the U-tec App, you must tap "Delete" from the Advanced
tab in the Settings section of the lock.
U-Bolt Pro
Rotate the handle to open the door.
2.4 Reset the Lock
- 5 -
· Emergency Key Override can be used when the battery is dead, or when no valid User Code is
known.
· The key hole is on the bottom of the exterior assembly of the lock, insert the key and rotate it
to unlock, just like any lock.
· Please take good care of your emergency keys.
2.6 Emergency Key Override
Ultraloq UL3 Series supports up to 16-digit Vague Code.Just enter any 16-digit code, as long as
a correct codeis included inwhat you entered, you canopen the door.
2.7 Vague Code
1. Your finger should cover the Reader completely with some pressure, touching the
whole reading area.
2. Make sure that your finger and the Fingerprint Reader are clean and dry, please note
that wet, oily, injured, peeled or dirty fingers may affect the fingerprint identification.
3. To clean the Fingerprint Reader, use a clean microfiber cloth to wipe off any dirt or debris.
4. While scanning your finger, you shouldn't tap too quickly or move your finger around.
5. In case of low recognition rate, please delete the original registered fingerprint and register
it again.
2.8 Finger Placement
1:
2:
3:
1 2 3 4 5 6
X X X X X X
1 2 3 4 5 6
X X X X X X
1 2 3 4 5 6
X X X X X X
Example
User Code: 123456
Vague Code Method
- 6 -
User ID is used to distinguish different users. It’s different from the Code. The User ID can be 1 to
8 numbers long. You can edit user’s fingerprint and code through User ID.
3.3 User ID
Factory Default Settings means that any fingerprint or code can unlock the UL3. The message
display shows “No User”.
3.1 Factory Default Settings
3.2 Owner, Admin and User
1. Activate the lock.
2. Press and hold for 3 seconds to enter the menu.
3. Input any number to select functions:
3.4 Basic programming steps
1Add User
6
3Delete Admin/User 4Edit Admin/User
Lockout Mode
2Add Admin
Passage Mode
5
2.9 Lock Status
Normal Mode
It’s the default mode, user must use the code, App access verification or scan the fingerprint
to unlock the UL3 from the outside.
Passage Mode
The UL3 will stay unlocked for convenient free passage.
Lockout Mode
The UL3 can only be operated manually by the backup Key. All electrical features are turned
off and only an Admin can disable it.
3. Basic Introduction
· The Owner is the person who owns the UL3 and registers it in U-tec App originally, the Owner
has all the privileges.
· The Admin can always unlock via fingerprint, code or App. Admin can add or delete other
Admins and Users, control all lock settings and view logs.
· The Normal User can always unlock via fingerprint, code or App.
· The Temporary User has limited access within a specific time range.
Edit Owner
7
- 7 -
4. Lock Setup
Scan the QR Code to download the U-tec App
Scan the above QR code to download the App, or search “U-tec”in App Store (iOS) and
Google Play (Android).
Open the App, register your U-tec account and log in the account.
Make sure the lock is in Factory Default Mode. Turn on Bluetooth on your smartphone,
stay near the lock (within 10 feet / 3 meters) and search the lock in the App.
Pair the lock in the App and start using it.
Note: Please refer to the guide in the U-tec App for more information.
Step 1
Step 2
Step 3
Step 4
Please go to page 8 for programming guide for Standalone Mode.
DON’T WANT TO USE THE APP?
- 8 -
Activate the Lock No User
Press and hold for 3 seconds
Press
Press
Operation Message Display
Enter a 4-8 Digit Code code then
Re-enter the Digit Code then
Success then Register finger2
Lift and place your finger covering the
whole area of the reader for 6 times
Success then Add User
Lift and place other finger covering the
whole area of the reader for 6 times
Add Owner
4-8 digit code
Enter again
Success then Register finger1
Welcome
5. Lock Programming by Touchscreen
Creating the Owner must be the first step prior to any other programming. Only one
Owner is available.
5.1 Create an Owner
Enter fingerprint or code from Owner or Admin,
then press
- 9 -
Note: It is recommended to keep track of the Users ID in case you want to update
any information later.
5.2 Add a Normal User
Activate the Lock, press and hold for 3 sec
Operation Message Display
Press
Enter a user ID, then press
Press to exit, or press to add a new user
Owner/Admin finger or code
Add User
Enter User ID
Register finger1
Lift and place your finger covering the whole
area of the reader for 6 times Success then Register finger2
Lift and place other finger covering the whole
area of the reader for 6 times Success then 4-8 digit code
Enter a 4-8 Digit Code code then Enter again
Re-enter the Digit Code then Success then Add User
Other manuals for Ultraloq UL3
6
Table of contents
Languages:
Other U-tec Door Lock manuals
